Hifonics Brutus Elite BE40-2000.1D Manual

Hifonics Modtager Brutus Elite BE40-2000.1D

Læs gratis den danske manual til Hifonics Brutus Elite BE40-2000.1D (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Hifonics Brutus Elite BE40-2000.1D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Power cable size

and fusing

It is critical to use the proper power

and ground cable. Select the size

listed here for your amplier model.

Always use high quality copper

cable. Visit our website for multi amp

system cable recommendations.

Be sure to use the proper fuse size

for each model.

Attach the chassis ground

cable to the amplier

negative terminal. It is

important to make sure this

connection is very tight.

Bare metal

Attach the main power cable

to the amplier +12V. The

cable must run directly to

the battery and be properly

fused and be very tight.

Attach the remote turn on

wire to the amplier remote

output of the source unit.

Connect the RCA cables to the

coordinating RCA input number

that will match the speaker

outputs number.

Connect the power cable to the

positive battery terminal. The

power cable must be fused

within 18 inches of the battery

terminal.

Re-connect the negative

battery terminal making sure it

is securely tightened.

The chassis ground connection

is critical to the performance

of the amplier. Choose a

location that is close to the

amplier. Completely scrape

away the paint and use a nut

and bolt if possible.

DO NOT USE AN EXISTING

FACTORY BOLT!

Negative Power

Connection

Positive Power

Connection

Remote Turn-on

Connection

Signal Input

Connection

Positive Battery

Connection

Re-connect

Negative Battery

Terminal

Chassis Ground

Be prepared to disarm your vehicle’s alarm and

to enter your radio / source unit code.

Before you start

CAUTION

Many new and factory radios require a reset code when

disconnected from battery power. This is an anti-theft

feature. Before unplugging power, you must determine if

your radio/source unit requires a reset code. Check the

operation manual for your vehicle or contact the dealer.

High Level Input

- DC turn on

- Music Sense

Low Level Input

- REM turn on

(Remote wire turn on)

Please scan QR code below or go to

Hifonics.com/product-manuals for the

Auto-Sense Technical Guide.

Turn on Mode

Model Fuse Size Cable Size

4ga

0ga

Using spade terminals,connect

the speaker cables to the speaker

output connectors. Follow the

diagram below that best ts your

speaker conguration.

Speaker

Connections

Stereo

Monoblock single woofer multiple woofersMonoblock

Bridged

MUSIC SENSE

DC SENSE

REMOTE

TURN ON MODE

NOTE - When using low level input and the RCA’s are plugged into the amplier and the TURN ON

MODE is in the DC ON position, the amplier will NOT turn on. Please re-read QR document above

or hire a professional installer.

BE40-1000.1D

BE40-1500.1D

BE40-2000.1D

BE40-3000.1D

BE40-1500.2D

BE40-1500.4D

BE40-2000.5D

2x60A

External 150A

External 200A

External 300A

External 150A

External 200A

Place terminal in a secure

position so that it won’t

accidentally contact the

negative battery post

Properly route power,

speaker and RCA cables

through the vehicle.

Choose a mounting location

that will provide adequate air

ventilation. Mount the amplier to

a secure surface. Do not mount

the amplier upside down.

Disconnect

Negative Battery

Terminal

Run Cables

Mount Amplier

Installation

CH1 CH2

Common System Setup

4ch - Full Range

4ch - Mixed Mono

Mono

5ch

CH1 CH2

2ch - Full Range

Quick Start

Installation Guide

Congratulations on your choice of a Hifonics amplier.

This “Quick Start Installation” guide is meant to help you

“hook up” and play music. For more detailed information,

on system setting, speaker and subwoofer conguration

and full specications by model visit the website,

http://hifonics.com/manuals.html

BE40-1000.1D

BE40-1500.1D

BE40-2000.1D

BE40-3000.1D

BE40-1500.2D

BE40-1500.4D

BE40-2000.5D

Adjusting your input level

Gives you the ability to ne tune the output signal

using the WIDTH and SWEEP knobs

Width Control

Controls how wide the frequency

range that is centered on the

sweep frequency

Sweep Control

Allows you to select the center

frequency

Input Level

Adjusting your input level

adjust your range switch to match your input range

level from your source unit, either High level(speaker

connections) or low-level inputs (RCA connection)

Disconnect speaker outputs

Play test tone (available on Hifonics.com

under the products support tab.)

Turn input clockwise until clip indicator LED (behind

level control dial) until it illuminates and then turn down

counterclockwise until LED turns off.

Once this is done you can stop the test tone track and

turn amplier off and reconnect the speakers leads to the

amplier.

While playing music you can now adjust and ne tune the

Effect levels: Bass, width and sweep controls.

WARRANTY

Maxxsonics, LLC. warrants this product, to the original consumer purchaser, to be free from

defects in material and workmanship for a period of one (1) year from the date of purchase.

Maxxsonics, LLC. will, at it’s discretion, repair or replace defective products during the warranty

period. Components that prove to be defective in materials and workmanship under proper

installation and use must be returned to the original authorized Maxxsonics, LLC. retailer from

where it was purchased. A photocopy of the original receipt must accompany the product being

returned. The costs associated with removal, re-installation and freight are not the responsibility of

Maxxsonics, LLC. This warranty is limited to defective parts and specically excludes any incidental

or consequential damages connected therewith. To view the full warranty, please visit the website.

The information contained within this document is intended to offer some basic guidelines for a few

of the most common installations. More complex audio systems should be installed by a professional.

Additional installation information available at

www.maxxsonics.com

HIFONICS products are designed and engineered in the USA by

www.maxxsonics.com HF BE40 QSG 01 - rev1

5CH2CH 4CH

MODE

4CH 2CH

MODE

Dual concentric bass knob to

adjust the bass level (A) and

output level (B)

Select between different LEDcolors and

sequences with the “RGB Color Selector”

button located on the end panel.

Remote Level

Control

RGB Controls

Effect Level

2CH - Input: CH1/CH2

Output: CH1/CH2/CH3/CH4

4CH - Input: CH1/CH2/CH3/CH4

Output: CH1/CH2/CH3/CH4

2CH - Input: CH1/CH2

Output: CH1/CH2/CH3/CH4/CH5

4CH - Input: CH1/CH2/CH3/CH4

Output: CH1/CH2/CH3/CH4/CH5

5CH - Input: CH1/CH2/CH3/CH4/CH5

Output: CH1/CH2/CH3/CH4/CH5

Input Mode

Setup

The illustrations below describe the various controls. Refer to

the illustration that matches your amplier.

The level control purpose is to match the output of your source signal to the

amplier. Refer to the section C & D for detailed instructions.

This switch will set the amplier to have a full frequency output or to lter out high

or low frequencies.

The Bass EQ control will increase the power output at 45Hz for more pronounced

bass. Exercise caution when using this control. Increase the level in small

amounts until distortion is noticed, then back off a little.

• Adjustable Bass Level Output

• Adjustable Bass Width and Sweep Adjustments

Refer to section F for detailed instructions.

Settings

LEVEL Adjustment

Mono-Block

4-Channel 5-Channel

2-Channel

X-OVER Switch

BASS BOOST

Effect Level

The Low Pass Filter will cut off the frequencies above the setting. The High Pass

Filter will cut off the frequencies below the setting.

The Subsonic control will cut off the frequencies between 15Hz-35Hz

Frequencies Adjustment

SUBSONIC Control

To gain access to the BE40

amplier series top mount setting

control panel carefully remove

the four screws and lift the face

plate up.

Open Control

Panel

3 4 5 51

1 1

3 3 3 51 4

3 3

3 52

Produkt Specifikationer

Mærke:	Hifonics
Kategori:	Modtager
Model:	Brutus Elite BE40-2000.1D

Har du brug for hjælp?

Hvis du har brug for hjælp til Hifonics Brutus Elite BE40-2000.1D stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Hifonics Manualer

Hifonics Zeus Street ZXS900/6 Manual

18 Juli 2025

Hifonics Zeus Evolution ZXE1000/2 Manual

16 Juli 2025

Hifonics Zeus Evolution ZXE4000/1 Manual

10 Juli 2025

Hifonics Zeus Evolution ZXE3000/1 Manual

10 Juli 2025

Hifonics Brutus BRX1116.1D Manual

4 Juli 2025

Hifonics Zeus Expansion ZXR750/1E Manual

17 Juni 2025

Hifonics Zeus Expansion ZXR7002 Manual

8 Juni 2025

Hifonics Zeus Power ZXR900/2 Manual

8 Juni 2025

Hifonics Zeus ZXR1200.4 Manual

8 Juni 2025

Hifonics Zeus Power ZXR500/4 Manual

7 Juni 2025

Modtager Manualer

Nyeste Modtager Manualer

Albrecht HAE75 Manual

1 August 2025

CYP AU-A220 Manual

30 Juli 2025

Sirus I-Amp 8.150T Manual

30 Juli 2025

AER Colourizer 2 Manual

30 Juli 2025

Sirus I-Amp 1.300T Manual

30 Juli 2025

PAC AP4-FD32 Manual

30 Juli 2025

CYP PUV-1540S-RX Manual

30 Juli 2025

ART USB Dual Pre Manual

29 Juli 2025

SSL Pure Drive Quad Manual

29 Juli 2025

SSL Pure Drive Octo Manual

29 Juli 2025