Honeywell HD4D9S Manual

Honeywell Overvågningskamera HD4D9S

Læs gratis den danske manual til Honeywell HD4D9S (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Honeywell HD4D9S, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Document 800-08065 – Rev E – 05/11
4-Inch Dome Camera
Quick Install Guide
Document 800-08065 – Rev E – 05/11
Regulatory Notices
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
Canadian Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential protection requirements of the EMC directive 2004/108/EC and the General Product Safety Directive
(GPSD) 2001/95/EC, conforming to the requirements of standards EN 55022 for emissions, EN 50130-4 for
immunity, and EN60950 for Electrical Equipment safety.
Package Contents
Fully assembled camera
Hardware kit
Mounting templates
This guide
Operating Notes
Warnings
• Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
• The use of CSA Certified/UL Listed Class 2 power adapters is required to ensure
compliance with electrical safety standards.
Power Supply This dome camera can operate on 24 V AC or 12 V DC.
Operating Conditions • Avoid viewing bright objects (for example, light fixtures) for
extended periods.
• Avoid operating or storing the unit in the following locations:
• Extremely humid, dusty, hot, or cold environments (where
the operating temperature is outside the recommended
range of
−
40°F to 131°F [
−
40°C to 55°C] with heater on)
• Close to sources of powerful electromagnetic radiation,
such as radio or TV transmitters
• Close to fluorescent lamps or objects reflecting light
• Under unstable light sources (may cause flickering)
WEEE (Waste Electrical and Electronic Equipment).
Correct disposal of this product (applicable in the European Union and other
European countries with separate collection systems)
This product should be disposed of, at the end of its useful life, as per
applicable local laws, regulations, and procedures.
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
Document 800-08065 – Rev E – 05/11
© 2011 Honeywell International Inc.
All rights reserved. No part of this
publication may be reproduced by any
means without written permission from Honeywell Systems. The information in this publication is believed to
be accurate in all respects. However, Honeywell Systems cannot assume responsibility for any
consequences resulting from the use thereof. The information contained herein is subject to change without
notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Flush mount Surface mount
Model Numbers
HD4D3S(X)
HD4D9S(X)
HD4DAFS(X)
HD4DIRS(X)
HD4US(X)
Adapter plate
Zoom lever
(bottom)
Legend
A = Tilt rotation
B = Horizontal rotation*
C = Pan rotation
* If necessary, loosen the
screw that locks the gimbal
assembly in place before
adjusting the camera.
OSD controller
To access the OSD menu,
press the OSD controller.
Use the joystick to navigate
through the menu.
Monitor out (2nd Video)
To verify that the view angle
and camera settings are
correct, you can connect to a
portable monitor using the
supplied adapter cable.
Note For detailed information regarding OSD menu options, refer to your model’s
user guide.
Legend
A =
Power connector
B =
BNC connector
C =
UTP connector
Do not touch or damage
the black vent.
Preparation Installation Setup
3. Connect the Wiring
Surface Mount
1. Disassemble the Camera
2. Prepare the Mounting Surface (Surface or Flush Mount)
a. Using the supplied 5/32-inch Allen key,
loosen the three security screws and
carefully remove the dome cover.
b. Gently pull the inner liner off of the base.
c. Remove the three M4×10 screws
connecting the base to the skirt, and
then lift the base off of the skirt.
4S Electrical Junction Box (Optional)
a. Attach the adapter plate to the electrical
box using appropriate screws (not
supplied).
b. Attach the base to the adapter plate
using the supplied M4×10 screws.
Electrical box
(not supplied)
Base
Flush Mount
•
With adapter plate:
Attach the base to the
mounting surface using the supplied M4×14
screws.
•
Without adapter plate:
Attach the base to the
mounting surface using appropriate screws
(not supplied).
Skirt
To reattach the dome cover after you
have mounted the camera and adjusted
the settings (
➋
,
➌
):
a. Push the inner liner onto
the base until it snaps into place.
b. Push the dome cover onto the base
and tighten the security screws.
Base
Base
Screws
(not supplied)
M4×14 screws
(supplied)
M4×10 screws
(supplied)
Screws
(not supplied)
M4×10 screws
(supplied)
Inner liner
Dome cover
a. Using the appropriate
mounting template, mark
the holes as required.
b. Insert screw anchors (not
supplied) into the holes.
Base
Skirt
Flush MountSurface Mount
a. Attach the skirt to the electrical box
using appropriate screws (not supplied).
b. Attach the base to the skirt using the
supplied M4×10 screws.
M4×10 screws
(supplied)
Screws
(not supplied)
Skirt
Base
a. Attach the skirt to the mounting surface
using appropriate screws (not supplied).
b. Attach the base to the skirt using the
supplied M4×10 screws.
1 2 3
Note Surface mount preparation shown.
Adapter plate
(optional)
Adapter plate
Focus lever
(top)
2. Configure the Camera Settings Using the OSD
1. Adjust the View Angle
A
C
B
A
B
C
a. Connect the video connector:
• BNC: Connect to a mating BNC
connector.
• UTP: Connect the blue wire to
Video+. Connect the white wire
to Video−.
b. Connect the 24 V AC/12 V DC
power connector.
c. Route wiring behind posts
(grayed area).
Electrical box
(not supplied)
To use the side conduit, remove the security
screw with the supplied 1.5 mm Allen key, and
then unscrew the conduit plug.

Produkt Specifikationer

Mærke: Honeywell
Kategori: Overvågningskamera
Model: HD4D9S

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell HD4D9S stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Honeywell Manualer

Honeywell

Honeywell Performance H4W8PER2V Manual

21 December 2024
Honeywell

Honeywell HC35WE5R3 Manual

21 December 2024
Honeywell

Honeywell HD3C Manual

23 September 2024
Honeywell

Honeywell iPCAM-PT Manual

24 August 2024
Honeywell

Honeywell Equip HD4HDIH Manual

20 August 2024
Honeywell

Honeywell HN30160200 Manual

16 August 2024
Honeywell

Honeywell HDZ30A Manual

13 August 2024
Honeywell

Honeywell Performance HD31H Manual

12 August 2024
Honeywell

Honeywell HD50 Manual

11 August 2024
Honeywell

Honeywell Equip HDZ30 Manual

10 August 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Arecont Vision

Arecont Vision SurroundVideo Omni SX AV12976DN-08 Manual

17 Juni 2025
Arecont Vision

Arecont Vision MegaDome G3 AV10355PMTIR-SH Manual

17 Juni 2025
Arecont Vision

Arecont Vision ConteraIP Indoor Dome AV05CID-201 Manual

17 Juni 2025
Arecont Vision

Arecont Vision ConteraIP Bullet AV5426PMIR-S Manual

17 Juni 2025
Arecont Vision

Arecont Vision ConteraIP Omni LX Remote Setup AV20476RS Manual

17 Juni 2025
Arecont Vision

Arecont Vision MegaDome G3 AV3355PMIR-SH Manual

17 Juni 2025
Arecont Vision

Arecont Vision MegaDome G3 AV2356PMIR-S Manual

17 Juni 2025
Arecont Vision

Arecont Vision SurroundVideo Omni SX AV12975DN-08 Manual

17 Juni 2025
Arecont Vision

Arecont Vision MicroDome Duo AV10655DN-NL Manual

17 Juni 2025
Arecont Vision

Arecont Vision MicroDome Duo AV4655DN-NL Manual

17 Juni 2025