Honeywell HED1PR3 Manual

Honeywell Overvågningskamera HED1PR3

Læs gratis den danske manual til Honeywell HED1PR3 (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Honeywell HED1PR3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

HED1PR3 HED3PR3/ True Day/Night

Indoor/Outdoor IR Ball IP Camera

Quick Installation Guide

Document - — A — 800 21229V1 Rev 10/2015

Thank you for purchasing a HED1PR3/ HED3PR3

camera. Follow the

instructions in this guide to

install and log in to

your instructions camera. For

on configuring the

camera, refer to the

Performance Series IP

Cameras User Guide on

the andsoftware

documentation CD that came

with your camera. If

you require additional

assistance, please call the

number shown

below.

Cautions and Warnings

WARNING To ensure compliance with electrical safety standards this product is

intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,

on the unit, output rated 12 V DC, minimum 0.33A, Tma=60Deg.C or from Power over

Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE

802.3af PoE standard.

The Ethernet connection is not intended to be connected to exposed (outside plant)

networks. Do not connect two power sources to the camera at the same time.

Invisible LED radiation (850 nm). Avoid exposure to beam.

Regulatory Statements

Information to the User: This has equipment been and tested found to comply with the limits afor

Class B digital device, pursuant to part 15 of the FCC are Rules. These limits designed to provide

reasonable against protection harmful interference a in residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that a particular interference will not occur in installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment is and off on, the user encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the the separation between equipment and receiver.

•

Connect the equipment into an outlet the a that on circuit different from to which receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Note Changes or modifications not expressly approved by party the responsible for compliance

could void the user’s authority to operate the equipment.

This B Class digital apparatus complies Canadian with ICES- 003.

Cet appareil numérique de du B à - la Classe est conforme la norme NMB 003 Canada.

Important Safeguards

•

Read and keep these instructions.

•

Do not aim the camera toward a bright light source for extended periods to prevent damage to

the imager. Avoid operating the unit under or close to unstable light sources (may cause

flickering), or close to fluorescent lamps or objects reflecting light.

•

Do not touch the camera lens.

•

Do not drop the camera or subject it to physical shock.

•

Do not use a strong or abrasive detergent when cleaning the camera.

•

Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the

operating temperature is outside the recommended range of - 4°F to 140°F (– 20°C to 60°C).

Note Do not apply power to the camera before completing installation.

Note Confirm the installation surface can support at least three times the weight of the camera.

Document - – A – 5 1 800 21229V1 Rev 10/201

Before You Begin

Before you begin, that check you have received all of the parts If any parts are listed below. missing

or your damaged, contact dealer immediately.

HED1PR3/HED3PR3 True Day/Night Indoor/Outdoor IR Ball IP Camera

Mounting the Camera

Route the cables through the camera base.

Align base the screw holes on the camera with the plastic wall anchors.

Insert - the three self tapping screws through the holes the in camera base, into the wall

•

Camera

•

Documentation CD

•

Quick install guide

Required tools:

•

A Phillips screwdriver

•

Self- tapping screws (×3)

•

Plastic 3) wall anchors (×

•

Mounting template

anchors, and then tighten them to secure camera the base in place.

Installing and Adjusting the Ball Camera

Connect the 45 port on the ball camera.Ethernet cable to the RJ-

If the other end of the Ethernet cable is NOT connected to a PoE (Power- -over Ethernet)

switch or NVR, connect the power connector of the camera to a 12- V DC power source.

Reattach the cover to the base, and then move the ball camera body to the desired position.

Installation and servicing should be performed only by qualified

and

experienced technicians to conform to all local codes and to maintain your

warranty.

Installing the Decorative Ring

Ceiling or wall

Wall anchor

Camera base

ST3x18 self

Gland cover

Decorative ring

Ball camera body

When you have achieved the desired field with the camera’s web viewer or a NVRof view ’s display,

install the decorative ring.

Align tabs the three on the decorative ring the the with slots on camera base.

Turn the decorative ring clockwise until it securely clicks into place.

Logging On to the Camera

Camera connected to a PoE port of the Honeywell Embedded NVR can be configured with the NVR

directly.

To log on to the camera with a PC, install the Honeywell Config Tool from the software and

documentation CD, find the camera and open the web browser with the Honeywell Config Tool. The

default user name is admin (case-sensitive) and the default password is 1234.

Removing the Ball Camera from the Base

Turn the clockwise out of the decorative ring camera base and separate the gland cover from

the camera base. Set the ball camera body aside.

Preparing the Mounting Surface

Place the mounting template on the mounting surface where you want to install the camera.

Drill three (3) holes in the mounting surface for the wall anchors. Insert the wall anchors.

Drill an appropriately sized and hole pull the cables through the mounting surface.

Document - – A – 5 800 21229V1 Rev 10/201

© 5 this publication 201 Honeywell International Inc. All rights reserved. No part of may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,

Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to Revisions editions change without notice. or new to this publication may be issued such to incorporate changes.

www.honeywell.com/security

+1 800 323 4576

(North America only)

www.honeywell.com/security/uk

+1 44 (0) 1928 754 028

(Europe only)

www.asia.security.honeywell.com

+86 21 22196888

(Asia Pacific only)

•