Honeywell Performance H4W8PR2 Manual

Honeywell Overvågningskamera Performance H4W8PR2

Læs gratis den danske manual til Honeywell Performance H4W8PR2 (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Honeywell Performance H4W8PR2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

H4W8PR2 WDR 8 MP IR Rugged Dome Camera

Quick Installation Guide

Thank you for purchasing a Honeywell Performance Series

IP camera. Follow the instructions in this guide to install

and log in to your camera. For instructions on configuring

the camera, refer to the user guide on the CD that came

with your camera. If you require additional assistance, call

the number listed for your region on the back cover.

Warnings and Cautions

WARNING

To ensure compliance with electrical safety standards, this product is

intended for use with a Listed Power Adapter marked “Limited Power

Source” or “LPS” on the unit, output rated to 12 VDC, minimum 0.33 A,

TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed

Information Technology Equipment meeting IEEE 802.3af PoE standard.

CAUTION

The Ethernet connection is not intended to be connected to exposed

(outside plant) networks. Do not connect two power sources to the camera at

the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam.

Important Safeguards

•

Read and keep these instructions

•

Confirm the installation surface can support at least three times the weight of the camera.

•

Do not apply power to the camera before completing installation.

•

Do not aim the camera toward a bright light source for extended periods to prevent damage to

the imager.

•

Avoid operating the unit under or close to unstable light sources (may cause flickering), or close

to fluorescent lamps or objects reflecting light.

•

Do not touch the camera lens.

•

Do not drop the camera or subject it to physical shock.

•

Do not use a strong or abrasive detergent when cleaning the camera.

•

Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where

the operating temperature is outside the recommended range of - (-22°F to 140°F 30°C to

60°C).

Before You Begin

Before you begin, check that you have received all the parts listed below. If any parts are

missing or damaged, contact your dealer immediately.

•

Camera

•

Installation CD

•

Quick installation guide

•

Allen key - (L wrench)

•

Self-tapping screws (×4)

•

Plastic anchors (×4)

•

Mounting template

CAUTION Installation and servicing should be performed only by qualified and

experienced technicians to conform to all local codes and to maintain your

warranty.

Mounting surface

Mounting template

Anchors

Camera assembly

Self-tapping screws

Dome cover

Locking screw

Allen key

Preparing the Mounting Surface

Apply the mounting template to the mounting surface.

Using the mounting template as a guide, drill three pilot holes in the mounting surface,

then hammer the supplied anchors into the holes.

Drill a cable entry hole in the mounting surface, then pull the required cables through the hole.

CAUTION

THIS SYMBOL INDICATES THAT

DANGE OUSR VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

WITHIN THE UNIT.

CA : TUTION O REDUCE THE RISK OF ELECTRIC

SHOCK, DO N T REM THE CO OVE OVER.

NO USER-SERVICEABLE PAR .TS INSIDE

REFER SER TO QUVICING ALIFIED SERVICE

PERSONNEL.

THIS SYMBOL INDICATES THAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANY THIS UNIT.

RISK OF ELECTRIC

SHOCK

DO N T OPENO

© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell

cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such changes.

Mounting and Aiming the Camera

Remove the dome cover from the camera assembly using the supplied Allen key.

If you using microSD with are a card the install it before continuing. See below for camera,

details.

1. Push and

slide metal

shell to

unlock

position.

2. Open

metal

shell.

3. Insert microSD

card.

4. Close metal

shell and

slide to lock

position.

Connect the cable to the RJ 45 port on theEthernet - camera.

If the other end of Ethernet cable is connected to a PoE (Powerthe not -over Ethernet) -

switch or NVR, connect the power connector of the camera to a 12 VDC power source.

Fix the camera assembly to the mounting surface using the supplied screws.

Aim screw the camera lens in the desired direction, then tighten the s on the camera

assembly.

Reattach the dome cover.

Logging On to the Camera

If the camera is connected to the PoE port of a Honeywell Embedded NVR, it can be configured

using the NVR.

To log on remotely from a PC, install the Honeywell Config Tool from the software and

documentation CD, find the camera on the network, and then open the web browser with the

Honeywell Config Tool. The default user name is admin (case sensitive) the- and default password

is . 1234

Note

• Only Internet Explorer 11 (or later) is supported.

• IP address of the device is assigned automatically by server. If the DHCP server DHCP

is not available, the device will acquire as the default IP 192.168.1.108 address.

Adjusting the Zoom and Focus Settings

After you have logged on to the camera, go to Setup > Camera > Conditions > Zoom and

Focus to fine tune the camera’s zoom and focus settings.-

Recommended Recorders

HEN*4

-8/16/32/64 channel Focus 4K NVRs (H.264 and H.265)

HEN*3 - ) 4/8/16/32 channel Performance Series NVRs (H.264 and H.265

Regulatory Statements

FCC Compliance

This equipment has been tested and found to comply with the for a limits Class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the interference at his

own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

This Class A digital apparatus complies with Canadian ICES- 003.

Manufacturer’s Declaration of Conformance

North America The equipment supplied with this guide conforms to UL 60950 1 and CSA C22.2 No. 60950- -1.

Europe The manufacturer declares that the equipment supplied is compliant with the European Parliament

and Council Directive on the of restriction the use of certain hazardous substances in electrical and electronic

equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and the essential of requirements

the EMC directive (2014/30/EU), conforming to the requirements of standards EN 55032 for emissions, EN

50130-4 for immunity, and EN -1 for 62368 electrical equipment safety.

CAUTION This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

WEEE (Waste Electrical and Electronic Equipment)

Correct disposal of this product (applicable in the European Union and other European countries with

separate collection systems).This product should be disposed of, at the end of its useful life, as per

applicable local laws, regulations, and procedures.

2700 Blankenbaker Pkwy, Suite 150

Louisville, KY, 40299, USA

www.honeywell.com/security

+1 800 323 4576

(North America only)

Aston Fields Road, Whitehouse Industrial

Estate Runcorn, Cheshire, WA7 3DL, UK

www.honeywell.com/security/uk

+1 44 (0) 1928 754 028

(Europe only)

Building #1, 555 Huanke Road, Zhang

Jiang Hi- Tech Park

Pudong New Area, Shanghai, 201203,

China www.asia.security.honeywell.com

+400 840 2233

(Asia Pacific only)

Document 800-24595 09– – Rev A /2018

Produkt Specifikationer

Mærke:	Honeywell
Kategori:	Overvågningskamera
Model:	Performance H4W8PR2

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell Performance H4W8PR2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Honeywell Manualer

Honeywell HC35W25R3 Manual

11 Juli 2025

Honeywell Performance H4W8PER2V Manual

21 December 2024

Honeywell HC35WE5R3 Manual

21 December 2024

Honeywell HD3C Manual

23 September 2024

Honeywell iPCAM-PT Manual

24 August 2024

Honeywell Equip HD4HDIH Manual

20 August 2024

Honeywell HN30160200 Manual

16 August 2024

Honeywell HDZ30A Manual

13 August 2024

Honeywell Performance HD31H Manual

12 August 2024

Honeywell HD50 Manual

11 August 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Elro CC40RXX Manual

31 Juli 2025

Elro CI5000 Manual

31 Juli 2025

Elro CZ40RIPS Manual

31 Juli 2025

FLIR ioi HD CB-5222 Manual

30 Juli 2025

Eufy Cam S3 Pro Manual

30 Juli 2025

Telycam Vision+ 4KN 30X Manual

30 Juli 2025

Marshall Electronics CV630-BI Manual

30 Juli 2025

Telycam Vision+ SE Manual

30 Juli 2025

FLIR Ariel CC-3405 Manual

29 Juli 2025

FLIR Ariel CM-3505 Manual

29 Juli 2025