Honeywell ST9520C Manual

Honeywell Temperaturkontrol ST9520C

Læs gratis den danske manual til Honeywell ST9520C (34 sider) i kategorien Temperaturkontrol. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Honeywell ST9520C, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/34
User Guide
Y9520Z Sundial RF2 Pack 5
How to use:
ST9520C Wireless Enabled 2 zone Programmer
DT92E Wireless Room Thermostats
BDR91T Wireless Enabled Relay Box (if installed)
System Components
Energy Efficiency and the Environment
Home energy use is responsible for more than ¼ of the total UK carbon emissions
which contribute to climate change. Heating and hot water systems based on
boilers account for of this figure, so it is important to understand how your
controls can help to maximize energy efficiency while maintaining your comfort.
Your Programmer should be used in conjunction with appropriate temperature
controls. In order to save energy the following general points should be observed:
1. Ensure your system contains room thermostats in 2 seperate zones, and that
both are set to appropriate temperature levels: typically 20°C for the main
occupied zone and 18°C for the less occupied zone (typically the bedrooms).
2.
Programme your heating and hot water to be off when you are not in the house. If
you are concerned about possible frost damage to any exposed pipe work, it is
advisable to fit a frost protection system – your installer can advise you about this.
3. Think about how you use your domestic hot water – if you have a storage
system, it is not necessary to have this switched on all the time, even when you
are in the house.
4. Consider the heat up times required for your central heating. Every home
responds differently when the heating is switched on. Adjust the start time so
that you are not cold when you get up in the morning. A shorter heat up time is
required for other heating periods.
5. In the evening, when the house is up to temperature, it is often possible to
switch off the heating up to an hour before you go to bed, without any noticeable
reduction in comfort.
This document is to be left with the user
and forms part of a Home Information Pack
This section is to be completed by the Installer
Honeywell Control Systems Ltd.
Arlington Business Park,
Bracknell
Berkshire
RG12 1EB
Technical Help Desk: 08457 678999
www.honeywelluk.com
50047645-006 A
© 2011 Honeywell International Inc.
PLEASE RESPECT YOUR ENVIRONMENT!
Take care to dispose of this product and any
packaging or literature in an appropriate way
WHAT IS A PROGRAMMER?
...an Explanation for Householders (as recommended by the Energy Savings Trust)
Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and
domestic hot water on and off at the same time, while others allow the domestic hot water and heating to
come on and go off at different times. Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle. On some
programmers you must also set whether you want the heating and hot water to run continuously, run under
the chosen ‘On’ and ‘Off’ heating periods, or be permanently off. The time on the programmer must be
correct. Some types have to be adjusted in spring and autumn at the changes between Greenwich Mean
Time and British Summer Time. You may be able to temporarily adjust the
heating programme, for example, ‘Override’, ‘Advance’, or ‘Boost’. These
are explained in the manufacturer’s instructions. The heating will not work
if the room thermostat has switched the heating off. And, if you have a hot-
water cylinder, the water heating will not work if the cylinder thermostat
detects that the hot water has reached the correct temperature.
WHAT IS A ROOM THERMOSTAT?
...an explanation for Householders (as recommended by the Energy Savings Trust)
A room thermostat simply switches the heating system on and off as necessary. It works by sensing
the air temperature, switching on the heating when the air temperature falls below the thermostat
setting, and switching it off once this set temperature has been reached. Turning a room thermostat to
a higher setting will not make the room heat up any faster. How quickly the room heats up depends on
the design of the heating system, for example, the size of boiler and radiators. Neither does the setting
affect how quickly the room cools down. Turning a room thermostat to a lower setting will result in the
room being controlled at a lower temperature, and saves energy. The heating system will not work if
a time switch or programmer has switched it off. The way to set and use your room thermostat is to
find the lowest temperature setting that you are comfortable with, and then leave it alone to do its job.
The best way to do this is to set the room thermostat to a low temperature – say 18ºC – and then turn
it up by one degree each day until you are comfortable with the temperature. You won’t have to adjust
the thermostat further. Any adjustment above this setting will waste energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only one room thermostat to
control the whole house. But you can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t have TRVs, you should choose
a temperature that is reasonable for the whole house. If you do have TRVs, you can choose a slightly
higher setting to make sure that even the coldest room is comfortable, then prevent any overheating
in other rooms by adjusting the TRVs.
Room thermostats need a free flow of air to sense the temperature, so they must not be covered by
curtains or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the
thermostat from working properly.
Location
ST9520C
DT92E
Zone 1
(typically in living room or hallway)
DT92E
Zone 2
(typically in bedroom or upstairs hallway)
BDR91T
(If installed, typically next to boiler)
ZONE 1 ZONE 2
EXTRA HOUR
OVERRIDE
EXTRA HOUR
OVERRIDE
NEXT
DAY
COPY
DAY
HOLIDAY
OK
NEXT
DAY/TIME
ZONE 1
ZONE 2
RUN
Zone 1 ‘ON’ period indicator
Time Display
LoT™ Technology Display
Programme Time Markers
Day of Week Indicator
RF Symbol
Zone 2 ‘ON’ period indicator
Zone 2 Extra Hour Button
Zone 2 Indicator Lamp
Zone 2 Override Button
Boiler Status Indicator
Slider
ECO Mode Active
Frost Protect Indicator
ECO Countdown Indicator
Heating Demand Indicator
Setpoint Change Buttons
ECO Button
OFF/Standby Button
OFF/Standby Indicator
RF Communications Indicator
Battery Low Indicator
Fault Indicator
Setpoint Indicator
Temperature Display
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
9
10
11
12
13
8
14
9
15
10
16
11
17
12
18
13
19
21
20
Zone 2 Operating Mode Indicator
Zone 2 Operating Mode Button
OK/Next Button
Clock – and + Buttons
Zone 1 Operating Mode Button
Zone 1 Operating Mode Indicator
Holiday Button
Copy Day Button
Next Day Button
Zone 1 Override Button
Zone 1 Indicator Lamp
Zone 1 Extra Hour Button
22
23
24
23
22
21
20
19
24
1 2 3 54 6 7
9
10
8
16 15
12
14 131718
35
Keep this document in a Home Information Pack
1234
5
6
8
7
9
13
11
12
10
ZONE ID NUMBER
DT92E CONTROLS LAYOUTST9520C CONTROLS LAYOUT
11
ST9520C
This product and its associated documentation and packaging are protected by various intellectual
property rights belonging to Honeywell Inc. and its subsidiaries and existing under the laws of the UK
and other countries. These intellectual and property rights may include patent applications, registered
designs, unregistered designs, registered trade marks, unregistered trade marks and copyrights.
Honeywell reserves the right to modify this document, product and functionality without notice. This
document replaces any previously issued instructions and is only applicable to the product(s) described.
This product has been designed for applications as described within this document. For use outside of
the scope as described herein, refer to Honeywell for guidance. Honeywell cannot be held responsible
for misapplication of the product(s) described within this document.
Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell
Technologies Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle, Switzerland by its Authorised
Representative Honeywell Inc.
CONFIGURATION & SERVICE DATA
Boiler & System Service Log
The space below can be used to provide a record of boiler & system services and
the names and contact numbers of the Installer and Service Personnel.
This information is important for a Home Information Pack.
Service/Installation
Date
Installation/Service
Engineer
Telephone Number /
Contact Details
Configurable Features Options Factory
setting
Installer configured
(note value)
DT92E Configuration Zone 1 Zone 2
Measurement offset -3.0°C to 0 to 3.0°C 0
Upper setpoint limit 21 to 35°C 35°C
Lower setpoint limit 5 to 21°C 5°C
Energy saving ECO setpoint 5 to 35°C 18°C
Zone ID number

Produkt Specifikationer

Mærke: Honeywell
Kategori: Temperaturkontrol
Model: ST9520C

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell ST9520C stil et spørgsmål nedenfor, og andre brugere vil svare dig


Temperaturkontrol Honeywell Manualer

Honeywell

Honeywell Y9420S Sundial RF2 Pack 3 Manual

7 Juli 2024
Honeywell

Honeywell ST6400S Manual

6 Juli 2024
Honeywell

Honeywell THR928SRT Manual

5 Juli 2024
Honeywell

Honeywell F74C Manual

4 Juli 2024
Honeywell

Honeywell ST9500C Manual

4 Juli 2024
Honeywell

Honeywell THR092HRT Evohome Manual

4 Juli 2024
Honeywell

Honeywell ST9520C Manual

4 Juli 2024
Honeywell

Honeywell ST6200A Manual

4 Juli 2024
Honeywell

Honeywell ST9400S Manual

4 Juli 2024
Honeywell

Honeywell ST9100A Manual

28 Juni 2024

Temperaturkontrol Manualer

Nyeste Temperaturkontrol Manualer

Atag

Atag MadQ Brain Manual

15 Januar 2025
ACV

ACV HeatMaster Manual

15 Januar 2025
Nefit

Nefit TA 250 Manual

14 Januar 2025
Viessmann

Viessmann Trimatik - 7450 286B Manual

14 Januar 2025
Viessmann

Viessmann Trimatik - 7450 286 Manual

14 Januar 2025
Viessmann

Viessmann Trimatik - 7450 365 Manual

14 Januar 2025
Viessmann

Viessmann Trimatik - 7450 285B Manual

14 Januar 2025
Samson

Samson 5312-2 Manual

14 Januar 2025
Viessmann

Viessmann Trimatik MC-B2 - 7450 362 Manual

14 Januar 2025
Samson

Samson EB 5207 Manual

14 Januar 2025