Hoymiles HMT-1800-6T Manual

Hoymiles Batterioplader HMT-1800-6T

Læs gratis den danske manual til Hoymiles HMT-1800-6T (2 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Hoymiles HMT-1800-6T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

2. Installation Steps

1. Accessories

Step 1. Plan and install the Microinverter

All accessories above are not included in the package and should be purchased separately.

Note:

1. Install the microinverter and all DC connections under the PV module to avoid direct sunlight, rain exposure, snow buildup, UV, etc.

2. Leave at least 2 cm of space around the microinverter enclosure to ensure ventilation and heat dissipation.

3. Mounting torque of the 8 mm screw should be 9 N·m. Please do not over-torque.

The order of Step 1 and Step 2 can be reversed according to your planned needs.

Item Description

A 3P-AC Trunk End Cap

B 3P-AC Trunk Connector

C 3P-AC Trunk Port Disconnect Tool

D 3P-AC Trunk Connector Unlock Tool

E 3P-AC Trunk Port Cap

DC Extension Cable,1m

3P-AC Trunk Cable, 12/10 AWG Cable

- Use the 3P-AC Trunk Connector Unlock Tool

to unlock the connector upper cover.

1 ) Disassemble the AC Trunk Connector and remove the cable.

2 ) Install the 3P-AC Trunk End Cap at one side of 3P-AC Trunk Cable (The end of 3P-AC Trunk Cable)

3 ) Install AC end cable on the other side of 3P-AC Trunk Cable (connected to the distribution box)

- Loosen the three screws with screwdriver.

Untighten the cap and remove the cable.

*Note:

HMT-2250/1800-6T Quick Installation Guide

A ) Mark the position of each microinverter on the rail, according to the PV module layout.

Step 2. Plan and Build the 3P-AC Trunk Cable

B ) Fix the screw on the rail.

C ) Hang the microinverter on the

screws, and tighten the screws. The silver

cover side of the microinverter should be

facing the panel.

- Insert the 3P-AC Trunk End Cap and screw

the cap back to port, then tighten the cap.

- Unlock the port upper cover, loosen the screws

with screwdriver and remove the extra cable.

(Skip this step if there is no cable at this side.)

- Plug the upper cover back to the Trunk

connector.

5.5±0.5N·m

Mounting Torque : 9 N·m

click

B C D E F GHA

M8*25 screws (Prepared by the installer)

3P-AC Trunk Cable is used to connect the microinverter to distribution box.

A ) Determine how many microinverters you plan to install on each AC branch and prepare AC Trunk Connectors

accordingly.

B ) Take out segments of AC Trunk Cable as you need to make AC branch.

Step 5. Connect PV Modules

Step 6. Energize the System

A )

Mount the PV modules above the

microinverter.

B )

Connect the PV modules’ DC cables to the

DC input side of the microinverter.

Note:

1. Tightening torque of the cap: 5.5±0.5 N·m. Please do not over-torque.

2. Torque of locking screw: 0.4±0.1 N·m.

3. Do not damage the sealing ring in the 3P-AC Trunk Connector during disassembly and assembly.

Step 4. Create an Installation Map

A )

Peel the removable serial number label from

each microinverter.

B )

Affix the serial number label to the respective

location on the installation map (please refer

to the appendix).

Note:

1. Make sure that the 3P-AC Trunk Connectors are kept away from any water-channeling surface.

2. In case you need to remove the microinverter AC cable from 3P-AC Trunk Connector, please use

the 3P-AC Trunk Port Disconnect Tool and insert the tool into the side of AC Sub Connector to

complete the removal.

Product information is subject to change without notice. (Please download reference manuals at www.hoymiles.com).

C ) Repeat the above steps to make all the 3P-AC Trunk Cables you need, then lay out the cable on the rail in the suitable

position so that the microinverters can be connected to the Trunk connectors.

Step 3. Complete the AC Connection

Note: Please use DC extension cables.

- Prepare a segment of AC cable with suitable

lengthto connect to the distribution box, with

stripping requirements fulfilled.

- Insert the cable into the cap in a way that

theL1, L2, L3, PE and N lines are in correspond-

ing slots.

- Tighten the screws: and tighten the cap back

to the port.

- Plug the upper cover back to the Trunk

connector.

B ) Connect the AC end cable to the distribution box, and wire it to the local grid network.

A) Turn on the AC breaker for the branch circuit.

B) Turn on the main AC breaker for the house. Your

system will start to generate power in about two

minutes.

Step 7. Set up Monitoring System

Please refer to the DTU User Manual or DTU Quick Install Guide,

and Quick Installation Guide for S-miles Cloud to install the DTU

and set up monitoring system.

D ) Attach the 3P-AC Trunk Cable to the

mounting rail and fix the cable with tie wraps.

A ) Push the AC Sub Connector from

microinverter to the 3P-AC Trunk Connector

until it clicks.

C ) Please plug the 3P-AC Trunk Port Cap in

any vacant AC Trunk Port to make it water and

dust-proof.

5.5±0.5N·m

0.4±0.1N·m

click

8±1mm

70±5mm

138264700571

To sheet ______

Sheet_____of_____

Hoymiles Microinverter Installation Map

Please Make N for North

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

COLUMN

ROW

AP040228 V1.3

Customer Information: DTU Serial Number

Azimuth:

Tilt:

Panel type:

Produkt Specifikationer

Mærke:	Hoymiles
Kategori:	Batterioplader
Model:	HMT-1800-6T

Har du brug for hjælp?

Hvis du har brug for hjælp til Hoymiles HMT-1800-6T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Hoymiles Manualer

Hoymiles HMT-1800-6T Manual

2 September 2024

Hoymiles HMT-2250-6T Manual

2 September 2024

Hoymiles HMS-1600 Manual

31 August 2024

Hoymiles HMS-1800 Manual

31 August 2024

Hoymiles HYS-4.6LV-EUG1 Manual

31 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Ansmann Powerline 5 LCD Manual

10 Oktober 2025

Ansmann XC 3000 Manual

10 Oktober 2025

Ansmann APS1500 Manual

10 Oktober 2025

Joy-It SBC-Buck04-5V Manual

8 Oktober 2025

Ansmann APM1 Manual

8 Oktober 2025

Ansmann USB-C Wall Charger 130PD Manual

8 Oktober 2025

Kress KAC877E Manual

5 Oktober 2025

Socket Mobile DuraCase Manual

3 Oktober 2025

Gardol 20V/30 Manual

3 Oktober 2025

Toolcraft ALG-1000 Manual

2 Oktober 2025