Hozelock Cascade 700 Manual

Hozelock Vandpumpe Cascade 700

Læs gratis den danske manual til Hozelock Cascade 700 (2 sider) i kategorien Vandpumpe. Denne vejledning er vurderet som hjælpsom af 75 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 38 anmeldelser. Har du et spørgsmål om Hozelock Cascade 700, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The Hozelock Cyprio Cascade 700 pump is

designed for submersible use only. The pump

does not use oil or grease for lubrication and

can be used safely in ponds containing ﬁsh or

plants. The motor consists of a sealed stator

and water-cooled permanent magnet rotor.

All electrical components are isolated from

the water.

IMPORTANT

1. WARNING: ALWAYS UNPLUG OR

DISCONNECT ALL APPLIANCES IN THE

POND FROM THE ELECTRICITY SUPPLY

BEFORE PUTTING YOUR HANDS IN THE

WATER WHILST EQUIPMENT IS BEING

INSTALLED, REPAIRED, MAINTAINED OR

HANDLED.

2. Do not use the supply cable to lift the

pump, as this may cause damage. We

recommend ﬁtting a lifting cord to the

handle eye on the top of the strainer cage

when the pump is installed in deep water.

See ﬁg 1.

3. Do not operate or leave the pump in

freezing conditions.

4. Do not allow the pump to run dry.

5. Check that the voltage marked on the

pump corresponds to the mains supply.

6. A 10MA OR 30 MA RESIDUAL CURRENT

DEVICE MUST BE FITTED TO THE MAINS

SUPPLY.

7. DO NOT OPERATE THIS PUMP WITHOUT

THE STRAINER CAGE ATTACHED. USING

THE PUMP WITHOUT A STRAINER MAY

INVALIDATE YOUR WARRANTY.

Safety Information

The appliance is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

they have been given supervision or

instruction concerning use of the

appliance by a person responsible

for their safety. Children should be

supervised to ensure that they do

not play with the appliance.

( ) This applianceAustralia & NZ only

is not intended for use by young

children or inﬁrm persons unless

they have been adequately

supervised by a responsible person

to ensure that they can use the

appliance safely.

Young children should be supervised

to ensure that they do not play with

the appliance.

WARNING: SAFETY AND

ELECTRICAL

CONNECTIONS

1. The pump is supplied with 10m of 3 core

electric cable which is permanently

connected and sealed to the motor.

The supply cable cannot be replaced. If the

cable is damaged, the pump should be

discarded.

This product is designed to be

permanently wired to the mains supply in

a dry weatherproof enclosure through a

Double-Pole Switched Fused Spur -

(Disconnector) to BS 3676, with a

minimum contact separation of 3mm in

each Pole - Fitted with a 3 or 5 Amp fuse.

The installation must conform to the

national and local wiring regulations

which could include the use of plastic or

metal conduit to protect the cable.

2. A 10MA OR 30MA RESIDUAL CURRENT

DEVICE (RCD) MUST BE FITTED TO THE

MAINS SUPPLY.

3. WARNING: THIS APPLIANCE MUST BE

EARTHED AND IT IS ESSENTIAL THAT THE

CONNECTIONS ARE MADE USING THE

FOLLOWING CODE;

Brown - Live

Blue - Neutral

Green/Yellow - Earth

The BROWN lead should be connected to

the LIVE terminal which may be marked

with an ‘L’ or coloured brown or red.

The BLUE lead should be connected to the

NEUTRAL terminal which may be marked

with an ‘N’ or coloured blue or black.

The GREEN/YELLOW lead should be

connected to the EARTH terminal which

may be marked with an ‘E’ or coloured

green or green/yellow.

4. If an extension cable is required, this

should be connected to the end of the

pump cable using a weatherproof cable

connector. The joint must be positioned in

a suitable weatherproof housing. The

extension cable should be of 3 core

0.75mm2Polychloroprene rubber insulated

cable (ref: HO5 RN-F) and permanently

wired to the mains supply with a 3 or 5

Amp fuse.

5. The pump cable (and extension cable)

should be positioned and adequately

protected against damage especially

where contact with gardening equipment

(lawn mowers, forks etc..) children and

domestic animals may occur.

6. CONSULT A QUALIFIED ELECTRICIAN OR

LOCAL AUTHORITY IF IN ANY DOUBT

ABOUT WIRING TO THE MAINS SUPPLY.

ACCESSORY ASSEMBLY

Telescopic Stem Assembly.

Take the outer telescopic stem ‘A’ and slide

the inner stem ‘B’ into it, as shown. See Fig 2.

Bell Fountain

1. Locate the Bell Support (D) to the Bell

Main Body (E) and push fully home.

2. Position the Bell (F) to the Body Assembly

and press into the central location.

See ﬁg 3.

PUMP INSTALLATION

Position

Construct a solid and level platform on which

to place the pump. Which using spray

fountains, the top of the platform should be

240-330mm (10-13”) below the water surface.

When using the bell fountain, the top of the

platform should be 100mm (4”) below the

water level.

A typical installation is shown for guidance in

ﬁg 4.

Flow Control

The ﬂow from the pump can be regulated to

meet your needs by rotating the ﬂow

controller wheel (G) near the outlet of the

pump. See Fig 5.

Fountain Only

1. Place the pump next to the pond and route

the cable back to the mains supply.

2. Select the desired fountain accessory. The

2 and 3 tier fountainheads simply snap

onto the fountain stem (See Fig 6). The

fountain stem pushes onto the narrower

tube section of the telescopic fountain

stem (See Fig 6). Then place the pump in

the desired position. Note: Check that the

inner stem of the telescopic tube has not

been pushed inside the outer tube.

3. a). 3 tier fountain – Creates a wide and

attractive fountain spray.

b). 2 tier fountain – Creates a higher and

narrower display.

c). Bell fountain – Creates a decorative

water bell. Adjust the telescopic stem to

the required height and regulate the bell

by rotating the ﬂow controller by the

outlet of pump.and by sliding the inner

bell in and out of the bell assembly.

4. The ball joint - See Fig 5 (H), ﬁts onto the

Cascade 700

INSTALLATION AND OPERATING INSTRUCTIONS. READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING INSTALLATION.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

3352

ATTENTION

AUTOMATIC CUT-OUT. To help ensure

your pump’s long life and to prevent

damage, it is ﬁtted with automatic

thermal overload protection. This

switches off the pump if it overheats. If

this occurs, switch off the power at the

mains supply to the pump. Check for the

cause. Usually it will be debris blocking

the inlets of the pump or obstructing the

impeller. Remove the obstruction and

wait 15 minutes for the pump to cool

down and automatically reset. Then

switch on the pump again.

NOTE: YOU MUST SWITCH OFF THE

MAINS SUPPLY BEFORE THE PUMP WILL

RESET.

From installing this1st January 2005

product in the garden is classed as

'notiﬁable' in the revised Building

Regulations for England and Wales. The

Regulations now require you to tell

your local authority building control

department that you intend to install

this product before installation. Your

local authority will let you know how

you can get your installation approved.

Produkt Specifikationer

Mærke:	Hozelock
Kategori:	Vandpumpe
Model:	Cascade 700
Type:	Brøndpumpe
Produktfarve:	Sort
Produkttype:	Vandpumpe
Strøm:	13 W
Pakkevægt:	1450 g
Pakkedybde:	103 mm
Pakkebredde:	208 mm
Pakkehøjde:	190 mm
Maksimalt driftstryk:	- bar
Materiale:	Metal,PVC
Normal brug:	Vandforsyning
Maksimal sugehøjde:	0.75 m
Maksimal leveringshøjde:	1.2 m
Gennemstrømningshastighed:	700 l/t
Leveringshoved:	1.2 m
Immersion, dybde (maks.):	- m