Hughes & Kettner BassBase 400 Manual

Hughes & Kettner Ikke kategoriseret BassBase 400

Læs gratis den danske manual til Hughes & Kettner BassBase 400 (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Hughes & Kettner BassBase 400, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/9
BEDIENUNGSANLEITUNG
400 WATTS
MANUAL
B A S S T E C H N O L O G Y
BASSBASE
400
-
MANUAL
SIGNAL LED:
Indicates the presence of an
instrument signal at the tube stage.
-10 db SWITCH: Lowers the
BASSBASE'S
input
impedance (e.g. for active instruments).
DIRECT: Press this button to send the original
instrument signal (unaffected by gain settings,
voicing controls, FX loop and notch filter)
directly to the DI OUT jack, at MIC level.
GROUND LIFT: Removes
the ground from the chassis
at the DI OUT jack.
I
,/’
,_‘.
,/,’
GRND DIR
0 0
-10
dB
0
CLIP LED: Indicates all types of clipping in the
BASSBASE’s
preamp (including post-EQ section and
FX loop distortion). In other words, an illuminated
CLIP LED does not necessarily mean the GAIN
control is set too high, it may also indicate the FX
signal level is not adjusted properly.
TUBE SATURATION LED: Indicates the
preamp is in tube overdrive mode.
MUTE: Switches all of the
BASSBASE
400’s outputs
except for the TUNER OUT off. Use this button for
breaks between sets, switching instruments, or
when tuning. The RED MUTE LED will illuminate
to indicate the amp is muted.
DI OUT: Use this jack to send signals to a
mixing console or additional power amp.
INPUT
-
Connect your bass to this jack.
CAIN: Controls the input sensitivity and drive
level of the
BASSBASE
preamp.
BASS: This EQ control defines the bottom end. At the 12 o’clock
position, the signal remains completely unaffected.
0
10
-5
-5
+5 -15
+15
FREQ
HZ
LEVEL
dB
t
TREBLE: Use this control to adjust the high end,
particularly the sizzle and overtone range.
FREQ HZ: Defines
the center frequency
for the
VARIMETRIC
-
EQ's
LOW RANGE
section. Please refer
to Section 3.2!
LEVEL: This control adjusts
the level of the frequency
you selected via the FREQ
HZ control. Turn
clockwise to increase,
counter-clockwise to
decrease.

Produkt Specifikationer

Mærke: Hughes & Kettner
Kategori: Ikke kategoriseret
Model: BassBase 400

Har du brug for hjælp?

Hvis du har brug for hjælp til Hughes & Kettner BassBase 400 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Hughes & Kettner Manualer

Hughes & Kettner

Hughes & Kettner ATTAX Manual

4 Juli 2025
Hughes & Kettner

Hughes & Kettner Attax 100 Manual

4 Juli 2025
Hughes & Kettner

Hughes & Kettner Edition 1 Manual

4 Juli 2025
Hughes & Kettner

Hughes & Kettner Edition Blue 15 Manual

4 Juli 2025
Hughes & Kettner

Hughes & Kettner BassKick 515 Manual

3 Juli 2025
Hughes & Kettner

Hughes & Kettner BassKick 111 Manual

3 Juli 2025
Hughes & Kettner

Hughes & Kettner Access Manual

3 Juli 2025
Hughes & Kettner

Hughes & Kettner Edition Silver 50 Manual

3 Juli 2025
Hughes & Kettner

Hughes & Kettner Tube Rotosphere MKII Manual

18 Juni 2025
Hughes & Kettner

Hughes & Kettner Switchblade 50 Combo Manual

18 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite

Tripp Lite TLM406NC Manual

31 Juli 2025
Tripp Lite

Tripp Lite Protect It! TLP76RBTEL Manual

31 Juli 2025
Tripp Lite

Tripp Lite N286-40G-ESR4-J Manual

31 Juli 2025
Emos

Emos H5011 Manual

31 Juli 2025
Emos

Emos ZM6145 Manual

31 Juli 2025
Oppo

Oppo Find X7 Manual

31 Juli 2025
Intellinet

Intellinet 713191 Manual

31 Juli 2025
Emos

Emos DCFW01 Manual

31 Juli 2025
AIC

AIC RSC-3ET Manual

31 Juli 2025
Tone City

Tone City King Of Blues Overdrive Manual

31 Juli 2025