Hughes & Kettner Switchblade 50 TSC Combo Manual

Hughes & Kettner Ikke kategoriseret Switchblade 50 TSC Combo

Læs gratis den danske manual til Hughes & Kettner Switchblade 50 TSC Combo (64 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Hughes & Kettner Switchblade 50 TSC Combo, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/64
english
deutsch
français
español
italiano
Switchblade TSC
Head 100, Combo 100, Combo 50
Manual 1.1
2
S w i t c h b l a d e T S C
Foreword
The installed Tube Safety Control (TSC) safeguards your tubes, amp, and sound.
Beyond that, for the first time it puts into your hands a tool that helps you
manage and check your old and new EL34 and even 6L6GC tubes at any time.
Players have long wished for a tube amp that is as low-maintenance as a solid-state
amps, and TSC has made that wish come true.
Best wishes from the Hughes & Kettner® team. We hope you enjoy playing your
SWITCHBLADE TSC as much as we enjoyed designing and refining it!
Things to Do Before Operating the Amp
Please read the safety instruction on page 64!
A word of warning before you fire up your SWITCHBLADE TSC: It’s loud!
High volume levels can cause hearing damage. Ensure plenty of air can circulate
around your amp‘s ventilation surfaces. Place the amp on a sturdy, secure base
and avoid exposing it to mechanical shocks and extreme temperatures that could
endanger the device or your and others‘ safety. The manufacturer disclaims any
liability or responsibility whatsoever for any damage or defect to this and other
devices resulting from misuse.
Powering Up
Ensure SWITCHBLADE TSC’s MAINS and STANDBY switches are off (with
the toggle switch pointing down) and that the voltage rating indicated next to the
MAINS INPUT (alongside the Voltage Setting arrow as depicted the illustration)
matches your local Mains current before you plug the amp in.
The illustration shows the 100/120 volt version as
an example. The voltage rating 100V is indicated
next to the arrow, meaning that the amp may be
powered with 100V Mains voltage only. If the
rating indicated next to the arrow does not match
the local Mains voltage, do not plug your SWITCHBLADE TSC’s Mains cord
into an outlet! More on this in chapter 9.
Head Only
First plug the speaker cord into the
appropriate output on the Head. Do
not use more than one of these outputs
simultaneously! That is, use either 1x4 Ω,
2x16 Ω, 1x8 Ω, or 1x16 Ω. Don’t mix and match cabinets either, say by plugging
a 4-Ω cabinet into the 4-Ω output and a 16-Ω cabinet into the 16-Ω output. For
more on this, see chapter 6.5.
Plug the other end of the cord into the speaker cabinet’s Input. This is vital
to every all-tube amp’s life! Power amps may be damaged when tube amps are
operated without a connected speaker load or at an insufficient impedance level!
Combo Only
Check to ensure the wire to the internal speaker is connected properly to the
power amp (see figure). Note that on the 50W Combo, the internal speaker is
connected to the 8-Ω output. On the 100W Combo, it is connected to the 16-Ω
output.
Head and Combo
To avoid very unpleasant surprises, make a habit of always twisting the MASTER
knob to the far left-hand position before turning on the amp.
Input
Connect your guitar to this Input. Please use suitable shielded cords only – no
speaker cords allowed.
Mains
This switch opens the flow of main current supply, and the blue PILOT LAMP
lights up. Ensure the STANDBY switch is set to OFF and allow the tubes plenty
of time to warm up. They’ll thank you for your patience with a longer service life.
Standby
The STANDBY switch breathes life into those glowing tubes. It controls the
anode voltage, not the heating. When taking a short break from playing, please
use STANDBY rather ON/OFF so the tubes remain at operating temperature.
If you can’t wait to get to it, go ahead and play your SWITCHBLADE TSC
now. The patient reader is well advised to continue reading before letting it rip.
Particularly chapters 1 (Handling) and 7 (Programming) are mandatory, even for
seasoned players.
Standard Setup and Cable Connections







Produkt Specifikationer

Mærke: Hughes & Kettner
Kategori: Ikke kategoriseret
Model: Switchblade 50 TSC Combo

Har du brug for hjælp?

Hvis du har brug for hjælp til Hughes & Kettner Switchblade 50 TSC Combo stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Hughes & Kettner Manualer

Hughes & Kettner

Hughes & Kettner ATTAX Manual

4 Juli 2025
Hughes & Kettner

Hughes & Kettner Attax 100 Manual

4 Juli 2025
Hughes & Kettner

Hughes & Kettner Edition 1 Manual

4 Juli 2025
Hughes & Kettner

Hughes & Kettner Edition Blue 15 Manual

4 Juli 2025
Hughes & Kettner

Hughes & Kettner BassKick 515 Manual

3 Juli 2025
Hughes & Kettner

Hughes & Kettner BassKick 111 Manual

3 Juli 2025
Hughes & Kettner

Hughes & Kettner Access Manual

3 Juli 2025
Hughes & Kettner

Hughes & Kettner Edition Silver 50 Manual

3 Juli 2025
Hughes & Kettner

Hughes & Kettner Tube Rotosphere MKII Manual

18 Juni 2025
Hughes & Kettner

Hughes & Kettner Switchblade 50 Combo Manual

18 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM

IFM SU9030 Manual

13 September 2025
IFM

IFM O2U554 Manual

13 September 2025
Speco Technologies

Speco Technologies HTi70TM Manual

13 September 2025
QSC

QSC RMXa Manual

13 September 2025
Tineco

Tineco Floor One S2 Series Manual

13 September 2025
Tineco

Tineco Floor One S3 Breeze Manual

13 September 2025
Tineco

Tineco Floor One S5 Steam Manual

13 September 2025
Osram

Osram VX500-CB Manual

13 September 2025
Zelmer

Zelmer ZTS7990 Manual

13 September 2025
Osram

Osram VX250-SP Manual

13 September 2025