Hunter 23852 Manual
Hunter
Ventilator
23852
Læs gratis den danske manual til Hunter 23852 (4 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Hunter 23852, eller vil du spørge andre brugere om produktet?
Side 1/4
Installation in concrete ceiling
CAUTION:
For concrete mounting, the drilled hole must be recommend-
ed by the manufacturer of the anchor (this is usually marked
on the anchor) and must be drilled at least 1/2" deeper than
the length of the anchor.
The holes must be made with a suitable carbide-tipped
masonry drill bit.
The anchors must be new and unused.
The concrete ceiling must be sound and free of cracks or
voids in the vicinity of the mounting holes.
The anchors must be set in flush with the surface of the
concrete.
The bracket screws must never be backed out. If the bracket
screws can be turned easily (by hand), do not hang fan.
Installation
Drill holes 2" deep in concrete ceiling to receive 1/4" x 11
/2"
expansion shield anchor, “Rawl No. 1055” or equal. (Not fur-
nished.) Install shield in holes, observing all cautions above.
Proceed with the installation of the fan per the basic installa-
tion instructions.
The Inside Story
Oil is constantly pumped up the spiral groove to lubricate the
rotor and shaft. The oil is returned to the reservoir where the
bearings are submerged in a bath of oil.
This unique lubrication system is built into all Original Hunter
Ceiling Fans. That’s one reason Hunters last so long. And why
we can offer a Limited Lifetime Warranty.
Fill in the blanks below for your record.
Serial number
Model number
Date purchased Date installed
Dealer/store name where purchased
4
41121-01 9/95
Trouble shooting guide
Problem Probable Cause Solution
1. Nothing 1. Power turned 1. Turn power on or
happens; off or fuse replace fuse.
blades do blown.
not rotate.* 2. Loose wire 2. Loosen canopy.
connections Check all
or wrong connections (turn
connections. power off while
checking).
3. Pull chain 3. Pull switch cord.
switch not
“on”.
4. Reversing 4. Slide reversing
switch in switch either up or
center. down.
* Note: If blades will not turn by hand, contact your nearest
service representative or dealer.
1. Noisy 1. Blade irons 1. Tighten screws until
operation. loosely snug.
screwed to
rotor.
2. Blade 2. Tighten.
screwed
loosely to
blade iron.
3. Blade cracked. 3. Replace all 4 blades.
Contact dealer.
4. Canopy 4. Lower canopy.
contacting
ceiling.
5. No oil or low 5. Check oil level.
oil level.
1. Excessive 1. Unbalanced 1. Rebalance (See
wobbling blades. Step 7D).
2. Inadequate 2. Relocate fan.
blade
clearance.
3. Loose blades 3. Tighten all screws.
or blade irons.
4. Fan not 4. Turn power off.
secure on Support fan very
hanger carefully. Loosen
assembly. canopy and hang
correctly.
1.
2.
3.
4.
5.
6.
A.
B.
HUNTER FAN COMPANY
25 00 FRISCO AVENUE
M E MP H I S , T N 3 8 1 1 4
®
Fig. 18
Hanger
Bracket Bracket
Power
Leads
Used With
Light Kit
Canopy
Set Screw
Oil Filler Hole
Oil Return
Rotor
Field
Windings Oil Reservoir
Bearing Nut
Switch Housing Cover
Bushing Pin
Ground Screw
Pipe Nipple (Std.)
Shaft
Cast Iron
Fan Housing
Cast Metal
Lower
Cover
Spiral
Groove
Bearings
Switch Housing
Pull Chain
Switch
expansion
shield anchor
set flush with
ceiling (anchor
not furnished)
Concrete ceiling
Bracket
(Furnished with fan)
Fig. 17
The installation of your Hunter Ceiling Fan
NOTE TO INSTALLERS: Please leave this manual with the
owner.
Tools needed:
• Pliers • 11/64" bit
• Flat blade screwdriver • 3 wire connectors
• Phillips screwdriver • 4" x 11/2" standard octagon
• Electric drill electrical outlet box
• 3/8" Socket wrench
Step 1: Pre-installation
Select installation site: Normally this is near the center of
the room, often replacing a light fixture. Make certain that
ample clearance is left for the rotating fan blades. For maxi-
mum efficiency, no obstruction (walls, posts, etc.) should be
within 24" of the tips of the blades (see Fig. 1). Mounting
site should also meet the precautions listed in Step 3.
Fan mounting height: Your Hunter fan comes with the proper
hardware to hang the fan from a standard 8 foot ceiling so
the fan blades will be 12" from the ceiling and approximately
7 feet from the floor (see Fig. 1).
NOTE: On vaulted ceilings, up to 45° pitch, you may want to
use the Hunter Vaulted Ceiling Mounting Kit.
Step 2: Inspect fan
Unpack the fan carefully to avoid any damage to com-
ponents.
CAUTION: NEVER LIFT THE MOTOR BY THE WIRES.
L E T M OT O R R E S T IN T H E C A R T ON L I N E R F OR
PROTECTION.
Check the sack parts.
Step 3: Installation of ceiling mounting hardware
CAUTION: YOUR HUNTER CEILING FAN WEIGHS UP TO 50
LBS. THE FOLLOWING PRECAUTIONS MUST BE TAKEN FOR
SAFETY AND TO ENSURE THAT YOUR FAN IS SECURELY
MOUNTED TO THE CEILING.
• When inspecting or preparing installation site where wiring
is available, make sure electricity is “off” at fuse box or
circuit breaker panel.
• All wiring must meet local and national codes.
• Do not mount directly to an unsupported ceiling or to an
electrical outlet box.
• The wood joist chosen for mounting the fan must be
sound and of sufficient size. In no case, should it be
smaller than standard 2" x 4" lumber.
Secure a metallic outlet box 4" x 11/2" or 4" x 1/2" deep to
2 x 4 cross brace between two ceiling joists as shown in
Figure 3. The outlet box must be recessed in the ceiling by
1/16" minimum. Secure the outlet box to the cross brace by
drilling (2) pilot holes no larger than the minor diameter of
the woodscrews ( 5/64") and use two #8 x 11
/2" woodscrews
and washers. Use the innermost holes for securing the box.
Orient the box so the outermost holes are aligned with the
2 x 4 brace. The outermost holes will be used in Step 3B.
CAUTION: Do not use a lubricant on screws.
SINCE 1 8 8 6
®
A.
B.
A.
A.
B.
INSTALLATION INSTRUCTIONS FOR
HUNTER ORIGINAL CEILING FANS
1
41121-01 9/95 ©1993 HUNTER FAN CO.™
CAUTION:
Read this entire instruction manual thoroughly before
beginning installation and SAVE THESE INSTRUCTIONS.
To avoid possible shock, BE CERTAIN ELECTRICITY IS
SHUT OFF AT MAIN PANEL BEFORE WIRING. Always
turn power off at main panel before servicing your fan or
installing accessories.
All wiring must be in accordance with national and local
electrical codes. If you are unfamiliar with wiring, you
should use a qualified electrician.
To reduce the risk of personal injury, install the fan only
to the building structure according to these instructions,
and use only the hardware supplied.
NEVER REST THE FAN ON THE SWITCH HOUSING. As
you prepare the fan for installation, let the motor rest in
the liner in which it was packed.
Be sure to put full contents of oil tube in fan according to
instructions.
If this fan is used as a replacement for an Original Old-
Tyme non-reversible fan, it must be installed per
instructions included with this fan. DO NOT HANG ON
SINGLE “J” HOOK. Failure to follow these instructions
could result in fan falling.
To reduce the risk of noise do not use a solid-state
speed control with this fan. Use Hunter controls only.
Do not use an abrasive cleaner on the fan. A mild
detergent will clean and restore most units to their
original beauty.
1.
2.
3.
4.
5.
6.
7.
8.
84" min. to floor
24" clearance
Fig. 1
Oil
Rubber Bushing
with Pin
Canopy Screws
Blade Screws
Blade Assembly Screws
Bracket Screws
Hanger Bracket Assembly
Pipe Nipple
in Motor Carton
Bracket
Fig. 2
12" minimum
Produkt Specifikationer
| Mærke: | Hunter |
| Kategori: | Ventilator |
| Model: | 23852 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Hunter 23852 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ventilator Hunter Manualer
19 August 2025
18 August 2025
18 August 2025
18 August 2025
16 August 2025
16 August 2025
16 August 2025
16 August 2025
28 Marts 2025
12 Januar 2025
Ventilator Manualer
- Orion
- Jocel
- Baseline
- Concept
- Havsö
- Izzy
- Hikoki
- Wentronic
- DeLonghi
- PAX
- Kunft
- Rovus
- Hom'Y
- Kambrook
- Cotech
Nyeste Ventilator Manualer
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025