Hunter Classic Original 23855 Manual

Hunter Ventilator Classic Original 23855

Læs gratis den danske manual til Hunter Classic Original 23855 (4 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Hunter Classic Original 23855, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Installation in concrete ceiling

CAUTION:

For concrete mounting, the drilled hole must be recommend-

ed by the manufacturer of the anchor (this is usually marked

on the anchor) and must be drilled at least 1/2" deeper than

the length of the anchor.

The holes must be made with a suitable carbide-tipped

masonry drill bit.

The anchors must be new and unused.

The concrete ceiling must be sound and free of cracks or

voids in the vicinity of the mounting holes.

The anchors must be set in flush with the surface of the

concrete.

The bracket screws must never be backed out. If the bracket

screws can be turned easily (by hand), do not hang fan.

Installation

Drill holes 2" deep in concrete ceiling to receive 1/4" x 11

/2"

expansion shield anchor, “Rawl No. 1055” or equal. (Not fur-

nished.) Install shield in holes, observing all cautions above.

Proceed with the installation of the fan per the basic installa-

tion instructions.

The Inside Story

Oil is constantly pumped up the spiral groove to lubricate the

rotor and shaft. The oil is returned to the reservoir where the

bearings are submerged in a bath of oil.

This unique lubrication system is built into all Original Hunter

Ceiling Fans. That’s one reason Hunters last so long. And why

we can offer a Limited Lifetime Warranty.

Fill in the blanks below for your record.

Serial number

Model number

Date purchased Date installed

Dealer/store name where purchased

41121-01 9/95

Trouble shooting guide

Problem Probable Cause Solution

1. Nothing 1. Power turned 1. Turn power on or

happens; off or fuse replace fuse.

blades do blown.

not rotate.* 2. Loose wire 2. Loosen canopy.

connections Check all

or wrong connections (turn

connections. power off while

checking).

3. Pull chain 3. Pull switch cord.

switch not

“on”.

4. Reversing 4. Slide reversing

switch in switch either up or

center. down.

* Note: If blades will not turn by hand, contact your nearest

service representative or dealer.

1. Noisy 1. Blade irons 1. Tighten screws until

operation. loosely snug.

screwed to

rotor.

2. Blade 2. Tighten.

screwed

loosely to

blade iron.

3. Blade cracked. 3. Replace all 4 blades.

Contact dealer.

4. Canopy 4. Lower canopy.

contacting

ceiling.

5. No oil or low 5. Check oil level.

oil level.

1. Excessive 1. Unbalanced 1. Rebalance (See

wobbling blades. Step 7D).

2. Inadequate 2. Relocate fan.

blade

clearance.

3. Loose blades 3. Tighten all screws.

or blade irons.

4. Fan not 4. Turn power off.

secure on Support fan very

hanger carefully. Loosen

assembly. canopy and hang

correctly.

HUNTER FAN COMPANY

25 00 FRISCO AVENUE

M E MP H I S , T N 3 8 1 1 4

Fig. 18

Hanger

Bracket Bracket

Power

Leads

Used With

Light Kit

Canopy

Set Screw

Oil Filler Hole

Oil Return

Rotor

Field

Windings Oil Reservoir

Bearing Nut

Switch Housing Cover

Bushing Pin

Ground Screw

Pipe Nipple (Std.)

Shaft

Cast Iron

Fan Housing

Cast Metal

Lower

Cover

Spiral

Groove

Bearings

Switch Housing

Pull Chain

Switch

expansion

shield anchor

set flush with

ceiling (anchor

not furnished)

Concrete ceiling

Bracket

(Furnished with fan)

Fig. 17

The installation of your Hunter Ceiling Fan

NOTE TO INSTALLERS: Please leave this manual with the

owner.

Tools needed:

• Pliers • 11/64" bit

• Flat blade screwdriver • 3 wire connectors

• Phillips screwdriver • 4" x 11/2" standard octagon

• Electric drill electrical outlet box

• 3/8" Socket wrench

Step 1: Pre-installation

Select installation site: Normally this is near the center of

the room, often replacing a light fixture. Make certain that

ample clearance is left for the rotating fan blades. For maxi-

mum efficiency, no obstruction (walls, posts, etc.) should be

within 24" of the tips of the blades (see Fig. 1). Mounting

site should also meet the precautions listed in Step 3.

Fan mounting height: Your Hunter fan comes with the proper

hardware to hang the fan from a standard 8 foot ceiling so

the fan blades will be 12" from the ceiling and approximately

7 feet from the floor (see Fig. 1).

NOTE: On vaulted ceilings, up to 45° pitch, you may want to

use the Hunter Vaulted Ceiling Mounting Kit.

Step 2: Inspect fan

Unpack the fan carefully to avoid any damage to com-

ponents.

CAUTION: NEVER LIFT THE MOTOR BY THE WIRES.

L E T M OT O R R E S T IN T H E C A R T ON L I N E R F OR

PROTECTION.

Check the sack parts.

Step 3: Installation of ceiling mounting hardware

CAUTION: YOUR HUNTER CEILING FAN WEIGHS UP TO 50

LBS. THE FOLLOWING PRECAUTIONS MUST BE TAKEN FOR

SAFETY AND TO ENSURE THAT YOUR FAN IS SECURELY

MOUNTED TO THE CEILING.

• When inspecting or preparing installation site where wiring

is available, make sure electricity is “off” at fuse box or

circuit breaker panel.

• All wiring must meet local and national codes.

• Do not mount directly to an unsupported ceiling or to an

electrical outlet box.

• The wood joist chosen for mounting the fan must be

sound and of sufficient size. In no case, should it be

smaller than standard 2" x 4" lumber.

Secure a metallic outlet box 4" x 11/2" or 4" x 1/2" deep to

2 x 4 cross brace between two ceiling joists as shown in

Figure 3. The outlet box must be recessed in the ceiling by

1/16" minimum. Secure the outlet box to the cross brace by

drilling (2) pilot holes no larger than the minor diameter of

the woodscrews ( 5/64") and use two #8 x 11

/2" woodscrews

and washers. Use the innermost holes for securing the box.

Orient the box so the outermost holes are aligned with the

2 x 4 brace. The outermost holes will be used in Step 3B.

CAUTION: Do not use a lubricant on screws.

SINCE 1 8 8 6

INSTALLATION INSTRUCTIONS FOR

HUNTER ORIGINAL CEILING FANS

CAUTION:

Read this entire instruction manual thoroughly before

beginning installation and SAVE THESE INSTRUCTIONS.

To avoid possible shock, BE CERTAIN ELECTRICITY IS

SHUT OFF AT MAIN PANEL BEFORE WIRING. Always

turn power off at main panel before servicing your fan or

installing accessories.

All wiring must be in accordance with national and local

electrical codes. If you are unfamiliar with wiring, you

should use a qualified electrician.

To reduce the risk of personal injury, install the fan only

to the building structure according to these instructions,

and use only the hardware supplied.

NEVER REST THE FAN ON THE SWITCH HOUSING. As

you prepare the fan for installation, let the motor rest in

the liner in which it was packed.

Be sure to put full contents of oil tube in fan according to

instructions.

If this fan is used as a replacement for an Original Old-

Tyme non-reversible fan, it must be installed per

instructions included with this fan. DO NOT HANG ON

SINGLE “J” HOOK. Failure to follow these instructions

could result in fan falling.

To reduce the risk of noise do not use a solid-state

speed control with this fan. Use Hunter controls only.

Do not use an abrasive cleaner on the fan. A mild

detergent will clean and restore most units to their

original beauty.

84" min. to floor

24" clearance

Fig. 1

Oil

Rubber Bushing

with Pin

Canopy Screws

Blade Screws

Blade Assembly Screws

Bracket Screws

Hanger Bracket Assembly

Pipe Nipple

in Motor Carton

Bracket

Fig. 2

12" minimum

Produkt Specifikationer

Mærke:	Hunter
Kategori:	Ventilator
Model:	Classic Original 23855

Har du brug for hjælp?

Hvis du har brug for hjælp til Hunter Classic Original 23855 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator Hunter Manualer

Hunter Spring Mill 51732 Manual

19 August 2025

Hunter Milstream 50735 Manual

18 August 2025

Hunter Brazos 52375 Manual

18 August 2025

Hunter Yuma 51453 Manual

18 August 2025

Hunter Lawndale Manual

16 August 2025

Hunter Presto Manual

16 August 2025

Hunter Gilrock Manual

16 August 2025

Hunter Zayden Manual

16 August 2025

Hunter Dempsey 59216 Manual

28 Marts 2025

Hunter Nova Manual

12 Januar 2025

Ventilator Manualer

Nyeste Ventilator Manualer

Grunkel MET-H16 Industrial Manual

14 September 2025

Grunkel SKYWIND-42BT Manual

13 September 2025

Grunkel TF-I45W Manual

13 September 2025

Create Air Mist Manual

13 September 2025

Antari AF-3X Manual

13 September 2025

MPM MWP-32 Manual

13 September 2025

Grunkel BreezeCraft FAN-165R Manual

13 September 2025

Be Cool BC18STTIDC Manual

11 September 2025

NuTone QTXN110HL Manual

10 September 2025

NuTone 744LEDNT Manual

10 September 2025