I3International Ax65W Manual

I3International Overvågningskamera Ax65W

Læs gratis den danske manual til I3International Ax65W (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om I3International Ax65W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CAMERA PARTS AND DEFINITIONS

3MP Infrared Outdoor IP Dome Camera w/ White Light Ax65W

Thank you for purchasing i3 International’s Annexxus 65W indoor/outdoor 3MP IP dome

camera with built-in white light. Your camera is equipped with a motorized vari-focal

3-10.5mm lens. The lens can be controlled through camera’s Web Interface in Internet

Explorer, through SRX-Pro Server/Remote or through Video Pilot Client. Built-in white light

settings can be congured only through camera’s Web Interface in Internet Explorer.

SAFETY

When installing your Ax65W camera be sure to avoid:

• excessive heat, such as direct sunlight or heating appliances

• contaminants such as dust and smoke

• strong magnetic elds

• moisture and humidity

• areas with mechanical vibrations

• uorescent lamps or objects that reect light and unstable light sources

• temperatures below -40° C (-40° F) and above 50° C (122° F).

POWER

This camera accepts AC24V and PoE+ power. Maximum power consumption: 25W.

Ensure the supplied voltage meets the power consumption requirements of this camera

before powering the camera on. Incorrect voltage may cause irreparable damage to the

video camera and will effectively void the camera warranty.

CLEANING

• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,

dry cloth to remove nger prints or dust from the dome cover.

• Use a blower to remove dust from the lens.

• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may

damage the surface nish.

SERVICING

To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the

camera. Refer servicing to qualied personnel only.

PACKAGE CONTENTS

Ensure that the items received match those listed on the order form and the packing slip.

In addition to this manual and a fully assembled camera, the dome camera packing box

includes:

A. Standard RJ45 Connector p1-x2

B. Round Head Screw (Tapping Type) w/ O-ring p1-x4

C. Plastic Anchor x4

D. 3ft network cable x1

E. Surface Mount template x1

F. Flush Mount template x1

G. Security torx bit x1

H. Long Machine type screws p1-x3

(for Flush Mounting with back box installations)

i3-TRNG-CAMS-Ax65W-QSG.indd

Rev. 171130

1. Back box. Camera’s back box comes with six (6) 90% pre-drilled hole dimples.

For surface mounting, complete drilling a minimum of two (2) holes.

2. Camera module / second housing.

3. Tilt bracket with locking screw

4. Inner liner / Shroud. Inner liner is attached to the camera module but can be

partially detached for easier lens adjustment.

5. IR board

6. Screws securing the dome bubble housing to camera module (x3, silver)

7. Dome bubble housing / Dome cover

8. Lexan bubble

9. 3/4” waterproof rubber plug. For best waterproof performance, use a network

cable 5mm or more in diameter. To maintain IP67 waterproof rating, use sealant

on the threads during installation. If using the side conduit hole, replace the

rubber plug with the metal plug from the side conduit.

10. 3/4” side conduit hole with metal plug. If using the side conduit hole, remove

the metal plug and use it instead of the rubber plug in the top conduit hole. To

maintain IP67 waterproof rating, use sealant on the threads during installation.

11. Six (6) 90% pre-drilled hole dimples. Complete drilling a minimum of two (2) for

surface mounting.

12. Reset/Default pin-hole button. Press for 1 second to reboot the camera.

Press for 6 seconds to restore camera settings to factory defaults.

13. Micro SD Card slot for on-camera video storage. (microSD card sold separately)

14. Mini USB port. Manufacturer use

only

15. Screws attaching camera module to the back box (x3, silver)

16. Screws to engage locking arms (x2, black)

Scan this QR code or visit ftp.i3international.com to view and

download the full User Manual for this camera. Also available for

download is the AnnexxusConfigurationTool or ACT program

used to locate and congure your cameras with your SRX-Pro

software. This program is already installed in SRX-Pro v3.3.3.69

and higher. Please contact our Technical Support team if you have

any questions or concerns regarding camera installation or you

require software services or support. Technical support can be

reached by email at: support@i3International.com or by

phone toll free 1.877.877.7241.

QR Code to Complete

User Manual / ACT

Lens Direction

GUIDE PATTERN

Cut Line

Camera Outline

Quick Start Guide

147 mm (5¾”)

68 mm (2.67”)

94 mm (3.7”)

158 mm (6¼”)

63 mm (2.5”)

84 mm (3.3”)

I/O CONNECTORS

Ax65W IP Dome Camera

QUICK START GUIDE

1.866.840.0004

www.i3international.com

Canada 780 Birchmount Road, Unit 16,

Scarborough, ON, M1K 5H4

1. Use the provided security Torx key to

loosen three silver screws securing

the dome bubble housing to camera

module (#6). Do not completely

remove the screws from the dome

bubble. Set the dome bubble aside.

2. Next, loosen three silver screws

attaching camera to the back box

(#15).

3. Remove camera’s back box and set

aside.

Once the camera’s back box has been removed, the Ax65W input/output connectors will be

revealed on the camera’s module, including RJ45 Ethernet/PoE+ connector, AC24V power

port and Audio/PIR/WLED connectors.

1. Audio Input/Output, PIR Input, Power to external PIR (no more than 2.0W), Power to

external White LED light (no more than 6.8W). Ax65W is compatible with i3 Mo-1

microphones. Note: If no Ext. WLED or PIR is used, Mo-1 microphone can be powered

directly from an otherwise unused WLED 12VDC or PIR 12VDC port.

2. AC 24V Port. Connect AC 24V power supply.

3. RJ45 Ethernet Connector / PoE+. Connect RJ45 network cable for Ethernet/Internet

connectivity. PoE+ (Power over Ethernet+) is supported.

Caution: Do not apply power until the camera is properly and securely mounted.

4. Orange LED. Flashing orange LED indicates data transmission between the camera

and the Internet.

5. Green LED. Solid green LED indicates a current live connection.

DISASSEMBLING THE CAMERA

U.S.A 4450 Witmer Industrial Estates Unit 4

Niagara Falls, NY 14305

FLUSH MOUNTING w/LOCKING ARMS

Note: Based on installation location and surface type, supplied screws and anchors may

not be adequate. This method is suitable for indoor drywall and T-bar installations only.

See complete manual for additional mounting options.

1. Use the Flush Mounting Template to cut a hole

in the mounting surface.

2. Disassemble the camera. Remove camera’s

back box and set aside. It will not be used in

this type of installation.

3. Insert the microSD card into the microSD slot

on the camera module (if using).

4. Insert the camera into the cut hole in the surface.

5. Feed all cables through the opening in the

mounting surface and connect to the camera. Do

not apply power until the installation is complete.

6. Use a Phillips screwdriver to turn two black-colored

screws on the camera module clockwise to engage

the locking arms. Tighten the arms securely

against the mounting surface.

7. Adjust the lens angle by rotating and panning the

camera lens base. Lift off the camera liner for

easy lens position adjustment. Do not over-rotate

the camera lens beyond the stop point to avoid

damage to the camera.

8. Once the desired view is achieved, replace camera liner until it snaps back into place.

9. Replace the camera’s dome bubble on top of the camera module. Use the red dots on

both modules for easy alignment.

10. Use the supplied Torx bit to re-tighten 3 silver screws securing the dome bubble

housing to the camera module.

4 5

Rev. 171130

Audio

Power to

Ext. WLED

≤ 6.8W

Au/I

GND

Au/O

WLED

12VDC

PIR/I

PIR

12VDC

GNDGND

CONNECTING CAMERA TO i3 SRX-PRO SERVER

Camera’s default IP address: 192.0.0.16.

Camera’s default Subnet mask address: 255.255.255.0.

Change your Annexxus camera’s default IP Address:

1. Close SRX-Pro Server software by pressing Alt+Shift+Ctrl+F4.

2. Change the IP address of the onboard NIC (LAN) of your SRX-Pro Server (or

of NIC1 if your SRX-Pro Server has two onboard NIC cards) to 192.0.0.XXX to

match the default IP range of your Annexxus IP camera.

3. Connect your Annexxus camera to i3 SRX-Pro Server (see diagram above).

4. Restart SRX-Pro Server software. Log in and go to the Setup -> IP Camera

tab.

5. Click ACT Config Tool icon. If your NVR does not have

Annexxus Conguration Tool, download and install it from

http://i3international.com/download website.

6. In ANNEXXUS Conguration Tool window, a list of active network cameras will

be displayed. Select your desired camera in the list.

7. Enter the new IP address and Subnet Mask of the camera in the Device(s)

Communication Update area and click Update. The new camera IP address

must match the

original

range of your SRX-Pro LAN or NIC1 card. E.g. If

your original SRX-Pro Server’s IP address was 192.138.10.122, change your

Annexxus camera’s IP address to 192.138.10.XXX.

Remember:

Annexxus Cameras cannot share an IP address, each camera

requires its own unique IP address.

8. Wait a few moments for a “Success” message in the Result eld.

9. Repeat Steps 7-8 for all detected Annexxus cameras in the ACT.

10. Change the IP address of the NIC back to its original setting (reverse Step 2).

Ensure you can connect to your camera using its new IP Address:

11. Open an Internet browser window and enter the new IP Address you have just

assigned to your Annexxus camera in Step 7.

12. Enter the default camera User Name and default Password in the pop-up login

window.

13. Annexxus camera interface will be displayed in the Internet Explorer window.

You should be able to see the camera image on the screen.

If you do not see the camera image on the screen, call i3 International

technical support team for troubleshooting tips: 1.877.877.7241

Add your Annexxus camera to IP Camera tab in SRX-Pro Server:

14. Ensure that the latest version of GiPi updater is installed on your SRX-Pro

Server. Latest GiPi available from http://i3international.com/download

Note:

SRX-Pro must be closed while GiPi updater is installed. After GiPi

updater installation, start i3 SRX-Pro Server software again.

15. Log In and go to the Setup -> IP Camera tab.

16. Click the Search & Add button to display connected Annexxus cameras.

17. Select the detected camera in the list and click Select.

18. In the

Select IP Camera

window, enter the default camera User Name and

Password, then click Add. Selected camera will be added to the IP Camera

list.

19. Assign the IP camera to the SRX-Pro video channel in the Ch In. column.

20. To enable motorized lens’ auto focus feature, go to Hardware tab and select

i3 GiPi from the PTZ Camera Type drop-down menu for the corresponding

channel.

Your Annexxus camera is now connected to SRX-Pro Server and is ready to record.

Change resolution and frame rate for the Annexxus camera in the IP Camera tab

menu or via Web Setup.

i3 SRX-Pro Server

LAN

Via Gigabit Switch

Connection Type 1:

(Camera requires AC power):

Connection Type 2:

i3 SRX-Pro Server

Audio

Out

Power to

PIR

≤ 2.0W

PIR

WHITE LED (WLED) LIGHT SETTINGS

Your camera comes equipped with the built-in white LED light, that can be automatically

activated whenever motion or human activity is detected by the camera. Built-in white light

can also be activated in response to the triggered PIR connected to the camera.

External Whilte Light (no more than 6.8W) can be connected directly to the camera and be

activated in response to the same events as the built-in WLED.

See complete manual for instructions.

Produkt Specifikationer

Mærke:	I3International
Kategori:	Overvågningskamera
Model:	Ax65W

Har du brug for hjælp?

Hvis du har brug for hjælp til I3International Ax65W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera I3International Manualer

I3International Veo17 Manual

31 August 2024

I3International Ax63Z Manual

31 August 2024

I3International Ax78R Manual

31 August 2024

I3International Ax65W Manual

31 August 2024

I3International Ax62 Manual

31 August 2024

I3International Ax51B Manual

31 August 2024

I3International i3F416U Manual

31 August 2024

I3International Ax68R Manual

31 August 2024

I3International Ax62C Manual

31 August 2024

I3International Ax40W2 Manual

31 August 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Speco Technologies O4LB2 Manual

9 Oktober 2025

Vaddio ZoomSHOT 20 SE AVBMP Manual

9 Oktober 2025

Speco Technologies O8VB3 Manual

9 Oktober 2025

Caliber HWC202PT Manual

9 Oktober 2025

Speco Technologies N8NSP6TB Manual

8 Oktober 2025

Speco Technologies O5D1G Manual

8 Oktober 2025

Speco Technologies O4TDD1M Manual

8 Oktober 2025

Speco Technologies ZIPT471 Manual

8 Oktober 2025

Caliber HWC 404 Manual

8 Oktober 2025

Speco Technologies O4BLP2M Manual

8 Oktober 2025