Ibanez RGIR28FE Manual

Ibanez Guitar RGIR28FE

Læs gratis den danske manual til Ibanez RGIR28FE (4 sider) i kategorien Guitar. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Ibanez RGIR28FE, eller vil du spørge andre brugere om produktet?

Side 1/4
Our congratulations and deepest thanks on
making Ibanez your choice of instrument.
Ibanez standards are second to none.
All Ibanez instruments are set up
to our strict quality control standards
before shipping.
The purpose of this manual is to explain
how to maintain your instruments finish
and to keep your guitar playing
as well as it did when it left our factory.
INSTRUCTION MANUAL
• M A I N T E N A N C E •
STRINGS AND TUNING MACHINES
If strings become dirty, discolored, or produce a dull sound or buzz,
replace the strings with new ones. For best results we recommend
replacing one string at a time, this will help to avoid removing the string
tension from the neck. When replacing strings with different gauge
strings, it may be necessary to adjust the truss rod tension. (We
recommend only qualified technicians perform this.) Instruments that
have tremolo systems installed may need to be adjusted after string
replacement as changes in string tension can cause the tremolo to raise
or lower. Please follow the instructions below for your particular model.
The strings should be tightly wound on to the
tuning machines from top to bottom with 2 to 3
string wraps around the post. In the case of
unwound guitar strings, the ends of the strings
should be prepared as shown in the diagram to
prevent unintentional slippage from the posts.
In the case of tuning machines, where the string
end s are
i n s e r t e d
int o t he
posts, the
string can be cut to length in
advance using a pair of string
cutters.
If the tuning machines are sealed
gear units, they are self-
lubricating types. The set screws
for the tuning knob are adjustment
screws that can be tightened with
a small Philips head screwdriver to
increase the tension.
*The use of coarse strings may lead to
buzzing and sound distortion. Using
strings that have twists or kinks may
cause buzzing or decreased sustain.
Make sure that the new strings ar e
smoot h an d fr ee f r om an y d e f ect s
before installing.
1
3
2
Ibanez s t eel s t ring
guitars and basses are
equi p p e d wit h
adjustable truss rods.
The purpose of a truss
ro d i s t o adjust the
ne ck to co unt e r act
string tension. There
are many reasons for
truss rod adjustments.
One of t h e most
frequent reasons is changing string gauges or tuning pitch which can
affect string tension. String tension changes may affect the string height
and cause fret buzz or notes that don’t ring true.
To adjust the truss rod,
locate the truss rod nut and
ad j ust it by i nsert i ng the
correct wrench into the nut
and tightening (clockwise) or
loosening (counter clockwise)
the rod. Truss rod tension
can be meas ure d by
installing a capo at the first
fret the holding the strings down at the fret position where the neck joins
the body. Insert a thickness gauge between the string and the fret at the
8th fret. There should between 0.3mm to 0.5mm clearance. That
clearance is referred to as “neck relief.” Too much neck relief can cause
the neck to have higher action in the middle of the neck causing poor
intonation and uncomfortable playability. No neck relief can cause fret
buzz.
*Appropriate care must be taken w hen adjusting the neck and we recommend only qualified
technicians perform this procedure.
LOOSEN
TIGHTEN
LOOSEN
TIGHTEN
LOOSEN
TIGHTEN
8th fret
NECK


Produkt Specifikationer

Mærke: Ibanez
Kategori: Guitar
Model: RGIR28FE

Har du brug for hjælp?

Hvis du har brug for hjælp til Ibanez RGIR28FE stil et spørgsmål nedenfor, og andre brugere vil svare dig