Ibanez SA360QM Manual

Ibanez Guitar SA360QM

Læs gratis den danske manual til Ibanez SA360QM (2 sider) i kategorien Guitar. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Ibanez SA360QM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTRUCTION MANUAL

• E L E C T R I C G U I T A R S •

w i t h L O C K I N G S Y S T E M

E L E C T R O N I C S

SWITCH FUNCTIONS

Ibanez Instruments are unique in the simplicity and versatility of our

switching systems. Each model was designed to allow the maximum

amount of useful pickup positions with the simplest operations.

Neck Center Bridge

RG, S, JEM, UV : Split-5 RG, S : Classic-5

Neck Center Bridge

JS900 : Standard-3

Neck Center Bridge

JS1000

Humbucking is parallel connected.

JS1000 : HIGH PASS FILTER SWITCH

The push/pull switch on the volume control in

the up position engages the high pass filter

system. This setting allows the volume to be

rolled back without losing the high frequencies.

CONTROLS

Tone

Volume

5way Pickup Selecter

Volume

w/High Pass On/Off Sw.

3way Pickup Selecter

Tone

w/Coil Tap On/Off Sw.

5way Pickup Selecter

Volume

1V, 1T JS1000

PGM

does not work when Coil Tap Sw. is “ON”

This is to certify that the aforementioned equipments fully conform to

protection requirements of the following EC council directives.

DIRECTIVES : 89/336/EEC Electromagnetic compatibility

DISTRIBUTED BY

B R I D G E I N F O R M A T I O N

STRING GAUGES

All guitars are set up at the factory with light gauge 009”- 042” strings

(7-string 009”- 054”). Different gauges of strings can result in the need

for string height, neck curvature, tremolo spring and intonation

readjustments.

Ibanez guitars feature four styles of locking tremolos. To identify which

tremolo is used on your guitar, locate the logo stamped either on the

bridge plate or the bridge tremolo block.

*Both Lo-Pro Edge and Edge tremolos have the “Edge” logo on the tremolo blocks.

*Adjustment of the 7-string tremolo is the same as the corresponding 6-string tremolo.

ADJUSTMENT

Lo-Pro Edge / Edge / Lo-TRS / TRS101

In the case of locking tremolos, replace the

strings one by one. Removing all the old

strings at once will release the tension on

the tremolo and change the tremolo angle

“up-pull.” Loosen the Pressure pad screw

(D) on the locking nut and loosen the string

to be replaced. Loosen the String stopper

screw (F) and remove the string from the

saddle. Cut off the ball end of new string as shown on the illustration and

insert the cut side of new string between the saddle and the String

holder block. Tighten the String stopper screw (F) and tune the string.

After checking the intonation, tighten the Pressure pad screw (D) on the

locking nut.

TRS505

In the case of TRS505 tremolo, replace the strings one by one. Removing

all the old strings at once will release the tension on the tremolo and

change the tremolo angle “up-pull.”

Loosen the Pressure pad screw (D) on the

locking nut and loosen the string to be

replaced. Remove the string through the

String holder hook (G). Thread new string

through the String holder hook (G) and tune

it. After checking the intonation, tighten the

Pressure pad screw (D) on the locking nut.

The tremolo springs adjust the tremolo

angle by tightening or loosening the tremolo

tension. To adjust tremolo angle, locate the

adjustment screws in the rear tremolo

cavity. The tremolo system when in tune

should sit parallel to the surface of the

guitar.

If the tremolo system is not sitting parallel to

the surfac e of the guitar, remove the

tremolo cavity cover plate and tighten the

Tremolo tension adjustment screws (H) if the tremolo is forward dumped.

Loosen the screws (H) if the tremolo is up-

pulled. Retune the strings to the proper pitch

and check the angle.

Edge and Lo-Pro Edge tremolos have the

Block Lock System to lock the tremolo springs

on the tremolo block. Remove the Block Lock

when replacing the springs. Choose the

number and placement of the tremolo springs

according to the string gauge and the tremolo

angle as follows.

Loosen the Pressure pad screw (D) on the locking nut and loosen the

string to be adjusted. Loosen the Saddle lock screws (E) on the saddle to

be adjusted and adjust the saddle forward or backward.

Tighten the Saddle lock screw (E) and tune the string. After rechecking

the intonation, tighten the Pressure pad screw (D).

On the base plate there are two holes for each Saddle lock screw (C).

These allow the user to change string gauges while allowing the

maximum saddle movement. If the intonation cannot be adjusted

because the saddle needs to be set back further, remove the intonation

screw and insert it into the hole located further back on the bridge plate.

LO-TRS

LO-PRO EDGE

(B) (E)

(A) (F)

LOCKING NUT (D)

TREMOLO ARM

Edge / Lo-Pro Edge

The tremolo arm can be inserted and removed very

easily. Insert the tremolo arm into the arm socket

and firmly push down until the arm snaps into

place. Both bushings should be completely hidden.

The rotation torque of the arm can be adjusted by

removing the bushings. To

further reduce the torque,

remove both bushings. To

replace the bushings, open

the new bushings at the split section and snap

them into place on the arm.

*After some time and use, it may impossible to secure

the arm even when both bushings are in place. If this

happens, replace the arm bushings with new ones.

Lo-TRS / TRS101 / TRS505

Insert the tremolo arm into the arm socket

and turn it clockwise until it stops. The

rotation torque of the arm can be adjusted by

turning the arm counterclockwise.

Lo-TRS and TRS tremolos are equipped with

a arm stop position screw located on the

bottom of the tremolo block and can be

adjusted by tightening the screw.

FINE TUNING

After locking the top lock, fine tuning the instrument can be done by

turning the fine tuning screws (A).

*To allow maximum fine tuning adjustment, it is recommended that the fine tuners be

set to the middle position before locking the nut.

STRING HEIGHT

The height adjustment of the tremolo can be raised or

lowered by adjusting the pivot studs(B) that the tremolo

mounts on. These are located at either side of the front

of the bridge. Clockwise lowers the tremolo and counter

clockwise raises the tremolo.

In the case of Edge and Lo-Pro Edge tremolos, the

Pivot studs(B) are locked internally by the Stud lock

screws(C). Always loosen the Stud lock screws (C)

before tightening the Pivot studs(B). After adjusting the

string height, tighten the Stud lock screws(C).

INTONATION

REPLACING THE STRINGS

TREMOLO SPRING

(A)

(B) (E)

TRS505

(B) (E)

(A)

(F)

TRS101

EDGE

(B/C) (E)

(A) (F)

(B/C) (E)

(A)

(F)

(C)

(G)

(H)

(H) (H)

Produkt Specifikationer

Mærke:	Ibanez
Kategori:	Guitar
Model:	SA360QM

Har du brug for hjælp?

Hvis du har brug for hjælp til Ibanez SA360QM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Guitar Ibanez Manualer

Ibanez SR370E Manual

2 September 2024

Ibanez SR300E Manual

2 September 2024

Ibanez AS73G-NT Manual

25 August 2024

Ibanez Premium SR1805E Manual

25 August 2024

Ibanez SR400QM Manual

25 August 2024

Ibanez RG852LW Manual

25 August 2024

Ibanez AEG10NII Manual

25 August 2024

Ibanez RGIR28FE Manual

25 August 2024

Ibanez RC320M Manual

25 August 2024

Ibanez SA360QM Manual

25 August 2024

Guitar Manualer

Nyeste Guitar Manualer

Behringer Analog Delay BM-14M Manual

1 Oktober 2025

Harley Benton Single Cut Manual

30 September 2025

Bugera 1960 Manual

14 September 2025

Zoom B1X Four Manual

11 September 2025

Line 6 Pad Go Manual

11 September 2025

Vertex Tone Secret Manual

5 September 2025

Fender Vintera '50s Stratocaster Manual

4 September 2025

Fender Player Jaguar Bass Manual

4 September 2025

Fender Jim Root Jazzmaster V4 Manual

4 September 2025

Fender Player Plus Nashville Telecaster Manual

3 September 2025