Icom i703 Manual

Icom Modtager i703

Læs gratis den danske manual til Icom i703 (112 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Icom i703, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/112

HF/50 MHz

ALL MODE TRANSCEIVER

i703

INSTRUCTION MANUAL

FOREWORD

Thank We understand that you have a choice of many

different radios in the market place. We want to take a

couple of moments of your time to thank you for mak-

ing the IC-703 your radio of choice, and hope you

agree with Icom’s philosophy of “technology first.”

Many hours of research and development went into

the design of your IC-703.

FEATURES

❍

DSP features (AF DSP; UT-106

DSP UNIT

required

some version)

❍

All mode capability covering 160–6 m

❍

9.0–15.87 V operation

❍

Compact with detachable front panel

❍

±0.5 ppm of high frequency stability

❍

Built in antenna tuner

❍

Simple band scope function

IMPORTANT

READ THIS INSTRUCTION MANUAL

CAREFULLY before attempting to operate the

transceiver.

SAVE THIS INSTRUCTION MANUAL. This

manual contains important safety and operating in-

structions for the IC-703.

EXPLICIT DEFINITIONS

RWARNING RF EXPOSURE! This device emits

Radio Frequency (RF) energy. Extreme caution should be

observed when operating this device. If you have any

questions regarding RF exposure and safety standards

please refer to the Federal Communications Commission

Ofﬁce of Engineering and Technology’s report on Evalu-

ating Compliance with FCC Guidelines for Human Radio

Frequency Electromagnetic Fields (OET Bulletin 65).

RWARNING HIGH VOLTAGE! NEVER attach an

antenna or internal antenna connector during transmis-

sion. This may result in an electrical shock or burn.

RNEVER apply AC to the [DC13.8V] receptacle on the

transceiver rear panel. This could cause a ﬁre or damage

the transceiver.

RNEVER apply more than 16 V DC, such as a 24 V

battery, to the [DC13.8V] receptacle on the transceiver

rear panel. This could cause a ﬁre or damage the trans-

ceiver.

RNEVER let metal, wire or other objects touch any in-

ternal part or connectors on the rear panel of the trans-

ceiver. This may result in an electric shock.

NEVER expose the transceiver to rain, snow or any liquids.

AVOID using or placing the transceiver in areas with tem-

peratures below –10°C (+14°F) or above +60°C (+140°F).

Be aware that temperatures on a vehicle’s dashboard can

exceed 80°C (+176°F), resulting in permanent damage to

the transceiver if left there for extended periods.

AVOID placing the transceiver in excessively dusty envi-

ronments or in direct sunlight.

AVOID placing the transceiver against walls or putting

anything on top of the transceiver. This will obstruct heat

dissipation.

Place unit in a secure place to avoid inadvertent use by

children.

During mobile operation, DO NOT operate the transceiver

without running the vehicle’s engine. When the trans-

ceiver’s power is ON and your vehicle’s engine is OFF,

the vehicle’s battery will soon become exhausted.

Make sure the transceiver power is OFF before starting

the vehicle. This will avoid possible damage to the trans-

ceiver by ignition voltage spikes.

During maritime mobile operation, keep the transceiver

and microphone as far away as possible from the magnetic

navigation compass to prevent erroneous indications.

BE CAREFUL! The rear panel will become hot when op-

erating the transceiver continuously for long periods.

BE CAREFUL! If a linear ampliﬁer is connected, set the

transceiver’s RF output power to less than the linear am-

pliﬁer’s maximum input level, otherwise, the linear ampli-

ﬁer will be damaged.

Use Icom microphones only (supplied or optional). Other

manufacturer’s microphones have different pin assign-

ments, and connection to the IC-703 may damage the

transceiver.

Beat signals may be heard on some frequencies.

These will occur as a result of circuit construction.

For U.S.A. only

Caution: Changes or modiﬁcations to this transceiver, not

expressly approved by Icom Inc., could void your authority

to operate this transceiver under FCC regulations.

PRECAUTION

WORD DEFINITION

RRWARNING Personal injury, ﬁre hazard or electric

shock may occur.

CAUTION Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No

risk or personal injury, fire or electric

shock.

Produkt Specifikationer

Mærke:	Icom
Kategori:	Modtager
Model:	i703

Har du brug for hjælp?

Hvis du har brug for hjælp til Icom i703 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Icom Manualer

14 Oktober 2024

5 Oktober 2024

5 Oktober 2024

5 Oktober 2024

26 September 2024

22 September 2024

20 September 2024

19 September 2024

16 September 2024

10 September 2024

Modtager Manualer

Nyeste Modtager Manualer

CYP AU-A220 Manual

30 Juli 2025

Sirus I-Amp 8.150T Manual

30 Juli 2025

AER Colourizer 2 Manual

30 Juli 2025

Sirus I-Amp 1.300T Manual

30 Juli 2025

PAC AP4-FD32 Manual

30 Juli 2025

CYP PUV-1540S-RX Manual

30 Juli 2025

ART USB Dual Pre Manual

29 Juli 2025

SSL Pure Drive Quad Manual

29 Juli 2025

SSL Pure Drive Octo Manual

29 Juli 2025

CYP PUV-1550SRX Manual

29 Juli 2025