Icom AT-140 Manual

Icom Modtager AT-140

Læs gratis den danske manual til Icom AT-140 (12 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Icom AT-140, eller vil du spørge andre brugere om produktet?

Side 1/12
2001 NEW
HF AUTOMATIC
ANTENNA TUNER
AT-140
INSTRUCTION MANUAL
AT-140_1.qxd 04.4.26 9:16 Page 1
i
2001 NEW 2001 NEW
FOREWORD
Thank you for purchasing the AT-140 HF AUTO-
MATIC ANTENNA TUNER.
The AT-140 is designed, primarily for use with Icom HF
transceivers.
Refer to your HF transceiver instruction manual for op-
eration. If you have any questions, contact your dealer.
IMPORTANT
READ ALL INSTRUCTIONS carefully and com-
pletely before using the AT-140.
SAVE THIS INSTRUCTION MANUAL. This in-
struction manual contains important safety and instal-
lation instructions.
EXPLICIT DEFINITIONS
PRECAUTIONS
RDANGER HIGH VOLTAGE! NEVER touch
the antenna terminal, ground terminal, antenna or
counterpoise while transmitting. Place the AT-140, an-
tenna and counterpoise in positions where no one can
touch them.
NEVER use without a ground connection.
NEVER transmit during internal adjustment. This may
cause an electric shock.
USE the ground terminal for ground connection.
The mounting plate is not connected internally.
DO NOT operate your HF marine transceiver without
running the boat’s engine.
AVOID using the AT-140 in areas where the temper-
ature is below –30°C (–22°F) or above +60°C
(+140°F).
Ground terminal
Mounting plate
Word Definition
RWARNING Personal injury, re hazard or electric
shock may occur.
CAUTION Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No
personal injury, re hazard or electric
shock.
SUPPLIED ACCESSORIES
The following accessories are supplied with the AT-140. Qty.
qU-bolts ……………………………………………… 2
wU-bolt plates ……………………………………… 2
eFlat washers (M6 large) ………………………… 8
rFlat washers (M6 small) ………………………… 4
tSpring washers (M6) ……………………………… 8
yNuts (M6) …………………………………………… 8
uHex head bolts (M6×50) ………………………… 4
iSelf-tapping screws (A0 6×30) …………………… 4
oWeatherproof cap ………………………………… 1
!0 4-pin/6-pin connector* …………………………… 1
!1 Connector pins* …………………………………… 4
!2 Ground cable (OPC-412) ………………………… 1
*The supplied connector and pins are differ according to ver-
sion.
q
w
e
r
t
y
u
i
o
!0 !1
!2
Icom, Icom Inc. and the are registered trademarks of Icom Incorporated (Japan) in the United States, the United King-
dom, Germany, France, Spain, Russia and/or other countries.
AT-140_1.qxd 04.4.26 9:16 Page 2


Produkt Specifikationer

Mærke: Icom
Kategori: Modtager
Model: AT-140

Har du brug for hjælp?

Hvis du har brug for hjælp til Icom AT-140 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Modtager Icom Manualer

Icom

Icom IC-M15 Manual

14 Oktober 2024
Icom

Icom IC-4008E Manual

5 Oktober 2024
Icom

Icom AT-140 Manual

5 Oktober 2024
Icom

Icom IC-25H Manual

5 Oktober 2024
Icom

Icom IC-T7H Manual

26 September 2024
Icom

Icom IC-M600E Manual

22 September 2024
Icom

Icom IC-PS25 Manual

20 September 2024
Icom

Icom IC-A22 Manual

19 September 2024
Icom

Icom IC-T81A Manual

16 September 2024
Icom

Icom IC-745 Manual

10 September 2024

Modtager Manualer

Nyeste Modtager Manualer