Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely
before using this product.
1-1-32 Kamiminami, Hirano-ku,
CAUTION: Shorter battery life could occur if the battery
is left fully charged, completely discharged, or in an
excessive temperature environment (above 50°C (122°F))
for an extended period of time. If the battery pack must
be left unused for a long time, it must be detached from
the transceiver after discharging. You may use the battery
pack until the remaining capacity is about half, then keep it
safely in a cool and dry place at the following temperature
–20°C ~ +50°C (–4°F ~ +122°F) (within a month)
–20°C ~ +40°C (–4°F ~ +104°F) (within three months)
–20°C ~ +20°C (–4°F ~ +68°F) (within a year)
BE SURE to replace the battery pack with a new one
approximately ve years after manufacturing, even if it still
holds a charge. The inside battery material will become
weak after a period of time, even with little use. The
estimated number of times you can charge the battery is
between 300 and 500. Even when the battery appears to
be fully charged, the operating time of the transceiver may
•Approximately ve years have passed since the battery was
•The battery has been repeatedly charged.
The battery cells may deteriorate and swell due to their
characteristics if used in an environment and conditions
such as: frequently charged, recharged immediately after
full charge, used or saved in a hot place, or charged
by methods other than the instructions. If the battery
pack swells, it has reached the end of its life due to
deterioration. Replace it with a brand new one.
RDANGER! NEVER charge the battery pack in areas
with extremely high temperatures, such as near res or
stoves, inside a sun-heated vehicle, or in direct sunlight.
In such environments, the safety/protection circuit in the
battery will activate, causing the battery to stop charging.
RWARNING! NEVER charge the transceiver during a
lightning storm. It may result in an electric shock, cause
a re or damage the transceiver. Always disconnect the
power adapter before a storm.
RWARNING! NEVER charge or leave the battery in the
battery charger beyond the specied time for charging. If
the battery is not completely charged by the specied time,
stop charging and remove the battery from the battery
charger. Continuing to charge the battery beyond the
specied time limit may cause a re, overheating, or the
RWARNING! Occasionally observe the battery pack
condition while charging. If any abnormal condition occurs,
discontinue using the battery pack.
RWARNING! NEVER insert the transceiver (battery
attached to the transceiver) into the charger if it is wet or
soiled. This could corrode the battery charger terminals or
damage the charger. The charger is not waterproof.
RCAUTION: NEVER charge the battery outside of the
specied temperature range: BC-214N and BC-219N
(16˚C ~ 40˚C (60.8˚F ~ 104˚F)). Otherwise, the charging
time will be longer, but the battery will not reach a full
charge. While charging, at a point after the temperature
goes out of the specied range, the charging will
SAVE THESE INSTRUCTIONS— These instructions contain
basic operating instructions for the IC-F52D/IC-F62D.
This instruction sheet includes some functions that are
usable only when they are preset by your dealer. Ask your
Personal death, serious injury or an
Personal injury, re hazard or electric
CAUTION Equipment damage may occur.
Recommended for optimum use. No risk
of personal injury, re or electric shock.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
•Force majeure, including, but not limited to, res,
earthquakes, storms, oods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
•The use of Icom transceivers with any equipment that is
not manufactured or approved by Icom.
Icom and the Icom logo are registered trademarks of Icom
Incorporated (Japan) in Japan, the United States, the United
Kingdom, Germany, France, Spain, Russia, Australia, New
Zealand, and/or other countries.
AMBE+2 is a trademark and property of Digital Voice Systems
word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
Icom Inc. is under license.
All other products or brands are registered trademarks or
trademarks of their respective holders.
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION: Changes or modications to this transceiver,
not expressly approved by Icom Inc., could void
your authority to operate this transceiver under FCC
This device complies with Part 15 of the FCC Rules.
Operation is subject to the condition that this device does
not cause harmful interference.
Company Name: Icom America Inc.
Address: 12421 Willows Road NE, Kirkland,
800-USA-ICOM (800-872-4266)
Monday – Friday 7 AM to 5 PM PST
CLEAN THE TRANSCEIVER THOROUGHLY IN A BOWL
OF FRESH WATER after exposure to saltwater, and dry
it before operating. Otherwise, the transceiver’s keys,
switches, and controllers may become unusable, due to
salt crystallization, and/or the charging terminals of the
battery pack may corrode.
NOTE: If the transceiver’s waterproof protection appears
defective, carefully clean it with a soft, damp (fresh water)
cloth, then dry it before operating. The transceiver may
lose its waterproof protection if the case or connector
cover is cracked or broken, or the transceiver has been
Contact your Icom distributor or your dealer for advice.
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed
solely for use within this Communications Equipment.
The user of this Technology is explicitly prohibited from
attempting to extract, remove, decompile, reverse
engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form.
#8,359,197 and #7,970,606.
RDANGER! NEVER short the terminals of the battery
pack. Shorting may occur if the terminals touch metal
objects such as a key, so be careful when placing the
battery packs (or the transceiver) in bags, and so on.
Carry them so that shorting cannot occur with metal
objects. Shorting may damage not only the battery pack,
but also the transceiver.
RDANGER! NEVER use or charge Icom battery packs
with non-Icom transceivers or non-Icom chargers. Only
Icom battery packs are tested and approved for use with
Icom transceivers or charged with Icom chargers. Using
third-party or counterfeit battery packs or chargers may
cause smoke, re, or cause the battery to burst.
RDANGER! NEVER operate the transceiver near unshielded
electrical blasting caps or in an explosive atmosphere.
RWARNING! NEVER operate the transceiver with a
headset or other audio accessories at high volume levels.
The continuous high volume operation may cause a
ringing in your ears. If you experience the ringing, reduce
the volume level or discontinue use.
RWARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention
— anything less could result in an accident.
CAUTION: DO NOT modify the transceiver. The
specications may change and then the transceiver may
not comply with the requirements of required regulations.
The transceiver warranty does not cover any problems
caused by unauthorized modication.
CAUTION: DO NOT carry the transceiver by holding the
CAUTION: DO NOT operate unless the exible antenna,
battery pack are securely attached to the transceiver.
Conrm that the antenna and battery pack are dry before
attaching. Exposing the inside of the transceiver to dust or
water can cause serious damage to the transceiver.
CAUTION: DO NOT use harsh solvents such as benzine
or alcohol when cleaning. This could damage the
equipment surfaces. If the surface becomes dusty or dirty,
wipe it clean with a soft, dry cloth.
CAUTION: DO NOT operate the transceiver if it becomes
hot after continuously transmitting for long periods of time.
This may damage the transceiver.
DO NOT place or leave the transceiver in direct sunlight or
in places with temperatures below –30°C (–22°F) or above
+60°C (+140°F). The basic operations of the transceiver
are guaranteed within the specied operating temperature
range. However, the Liquid Crystal Display may not operate
correctly, or show an indication in the case of long hours of
operation, or after being placed in extremely cold areas.
NEVER place the transceiver in an insecure place to avoid
inadvertent use by unauthorized persons.
BE CAREFUL! The transceiver meets IP67* requirements
for dust-tight and waterproof protection. However, once the
transceiver has been dropped, dust-tight and waterproof
protection cannot be guaranteed due to the fact that
the transceiver may be cracked or the waterproof seal
* Only when the BP-290 or BP-294, exible antenna, and
the connector cover or the optional speaker microphone
Even when the transceiver power is OFF, a slight current
still ows in the circuits. Remove the battery pack from the
transceiver when not using it for a long time. Otherwise,
the installed battery pack will become exhausted, and will
need to be recharged or replaced.
MAKE SURE to turn OFF the transceiver power before
connecting the supplied or optional equipment.
Operate the transceiver that complies with your local laws
Depending on countries and/or regions, transceiver’s
output power and/or operations on specic frequencies
may be restricted to avoid interferences with existing radio
Misuse of Li-ion batteries may result in the following
hazards: smoke, re, or the battery may rupture. Misuse
can also cause damage to the battery or degradation of
RDANGER! NEVER NEVER solder the battery terminals, or
modify the battery pack. This may cause heat generation,
and the battery may burst, emit smoke or catch re.
RDANGER! NEVER place or leave battery packs in
areas with temperatures above 60°C (140°F). High
temperature buildup in the battery cells, such as could
occur near res or stoves, inside a sun-heated vehicle,
or in direct sunlight for long periods of time may cause
the battery cells to rupture or catch re. Excessive
temperatures may also degrade the battery pack’s
performance or shorten the battery cell’s life.
RDANGER! NEVER strike or otherwise impact the battery
pack. Do not use the battery pack if it has been severely
impacted or dropped, or if the pack has been subjected to
heavy pressure. Battery pack damage may not be visible
on the outside of the case. Even if the surface of the
battery does not show cracks or any other damage, the
cells inside the battery may rupture or catch re.
RDANGER! NEVER expose the battery pack to rain,
snow, seawater, or any other liquids. Do not charge or
use a wet pack. If the pack gets wet, be sure to wipe it dry
RDANGER! NEVER place or leave battery packs near
re. Fire or heat may cause them to rupture or explode.
Dispose of used battery packs in accordance with local
RDANGER! NEVER let uid from inside the battery get
in your eyes. This can cause blindness. Rinse your eyes
with clean water, without rubbing them, and immediately
RWARNING! NEVER put the battery pack in a microwave
oven, high-pressure container, or in an induction heating
cooker. This could cause a re, overheating, or cause the
battery cells to rupture.
RWARNING! NEVER use the battery pack if it emits an
abnormal odor, heats up, or is discolored or deformed. If
any of these conditions occur, contact your Icom dealer or
RWARNING! NEVER use deteriorated battery packs.
RWARNING! NEVER Iet uid from inside the battery cells
come in contact with your body. If it does, immediately
CAUTION: DO NOT use the battery pack out of the
specied temperature range for the transceiver (–30°C
~ +60°C (–22°F ~ +140°F)) and the battery itself (–20°C
~ +60°C (–4°F ~ +140°F)). Using the battery out of its
specied temperature range will reduce its performance and
battery cell’s life. Please note that the specied temperature
range of the battery may exceed that of the transceiver. In
such cases, the transceiver may not work properly because
it is out of its operating temperature range.
SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic
energy while transmitting. This radio is designed
for and classied as for “Occupational Use Only.”
This means it must be used only during the
course of employment by individuals aware of
the hazards, and the ways to minimize such hazards. This
radio is NOT intended for use by the “General Population”
in an uncontrolled environment. This radio has been tested
and complies with the FCC and IC RF exposure limits
for “Occupational Use Only”. In addition, your Icom radio
complies with the following Standards and Guidelines with
regard to RF energy and electromagnetic energy levels
and evaluation of such levels for exposure to humans:
•FCC KDB Publication 447498 D03, Evaluating Compliance
with FCC Guidelines for Human Exposure to Radio
Frequency Electromagnetic Fields.
•American National Standards Institute (C95.1-2019), IEEE
Standard for Safety Levels with Respect to Human Exposure
to Electric, Magnetic, and Electromagnetic Fields, 0 Hz to
•American National Standards Institute (C95.3-2021),
IEEE Recommended Practice for Measurements and
Computations of Electric, Magnetic, and Electromagnetic
Fields with Respect to Human Exposure to Such Fields, 0 Hz
•The antennas, batteries, belt clips, speaker-microphone,
and other accessories that are listed in “OPTIONS” on the
INSTRUCTIONS sheet, are authorized for use with this
product. Use of accessories other than those specied may
result in RF exposure levels exceeding the FCC and IC
requirements for wireless RF exposure.
•Health Canada Safety Code 6 - Limits of Human Exposure to
Electromagnetic Energy in the Frequency Range from 3 kHz
To ensure that your expose to RF
electromagnetic energy is within the FCC and
IC allowable limits for occupational use, always
adhere to the following guidelines:
DO NOT operate the radio without a proper antenna
attached, as this may damage the radio and may also
cause you to exceed FCC and IC RF exposure limits. A
proper antenna is the antenna supplied with this radio by
the manufacturer or an antenna specically authorized by
the manufacturer for use with this radio.
DO NOT transmit for more than 50% of the total radio use
time (“50% duty cycle”). Transmitting more than 50% of
the time can cause FCC and IC RF exposure compliance
requirements to be exceeded. The radio is transmitting
when the LED indicator lights red. You can cause the radio
to transmit by pushing the “PTT” switch.
ALWAYS keep the antenna at least 2.5 cm (1 inch) away
from the body when transmitting, and only use the Icom
belt-clips listed in “OPTIONS” of the INSTRUCTIONS
sheet when attaching the radio to your belt, or other
place, to ensure FCC and IC RF exposure compliance
requirements are not exceeded.
The information listed above provides the user with the
information needed to make him or her aware of RF
exposure, and what to do to assure that this radio operates
within the FCC and IC RF exposure limits of this radio.
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF
energy that can possibly cause interference with other
devices or systems. To avoid such interference, turn o
the radio in areas where signs are posted to do so. DO
NOT operate the transmitter in areas that are sensitive to
electromagnetic radiation such as hospitals, aircraft, and
Occupational/Controlled Use
The radio transmitter is used in situations in which persons
are exposed as a consequence of their employment,
provided those persons are fully aware of the potential for
exposure and can exercise control over their exposure.
•Some accessories are not supplied, or the shape is dierent,
depending on the transceiver version.
•Conrm both battery sliding locks are locked in place, when
attaching the battery to the transceiver. Both sliding locks
make a ‘click’ sound when locked.
DAbout the Status indicator
•Lights white, then blinks red, yellow, and green when
turning ON the transceiver.
•Lights red while transmitting.
•Lights green while receiving a signal, or when the
DAbout the Multi-connector
Connects to an optional speaker microphone or headset.
CAUTION: DO NOT use the transceiver without the
connector cover or the optional microphone attached.
The transceiver meets IP67 requirements for dust-tight
and waterproof protection only when the connector cover
or the optional microphone is attached.
DAbout the Software key functions
Your dealers can assign the Software key functions to the
Hereby, Icom Inc. declares that the
versions of IC-F52D and IC-F62D which
have the “CE” symbol on the product,
comply with the essential requirements of
the Radio Equipment Directive, 2014/53/
EU, and the restriction of the use of certain hazardous
substances in electrical and electronic equipment
Directive, 2011/65/EU. The full text of the EU declaration
of conformity is available at the following internet address:
https://www.icomjapan.com/support/
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds
you that in the European Union, all electrical
and electronic products, batteries, and
accumulators (rechargeable batteries) must
be taken to designated collection locations at
the end of their working life. Do not dispose
of these products as unsorted municipal waste. Dispose of
them according to the laws in your area.
To obtain the UKCA Declaration of Conformity, please
contact Icom UK Limited by email at info@icomuk.co.uk or
alternatively call + 44(0) 1227 741741.
Battery pack Belt clip Connector cover
