Imou Cube PoE Manual

Imou Kamera Cube PoE

Læs gratis den danske manual til Imou Cube PoE (3 sider) i kategorien Kamera. Denne vejledning er vurderet som hjælpsom af 66 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 33.5 anmeldelser. Har du et spørgsmål om Imou Cube PoE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Installing Camera

Make sure the mounting surface is strong enough to hold at least

three times of the device weight.

Expansion Bolt

Camera

About the Guide

- This quick start guide is for reference only. Minor difference might

be found in user interface.

- All the design and software here are subject to change without

prior written notice.

- All trademarks and registered trademarks mentioned are the

properties of their respective owners.

- Please visit our website or contact your local service engineer for

more information.

- If there is any uncertainty or controversy, please refer to our final

explanation.

Alarm Input/output

The camera can connetct to external alarm input/outpiut device

through digital input/output.

Device collects different states of alarm input port when the input

signal is idling and being grounded.

Device collects logic "1" when input signal is connecting to +3V to

+5V or idling.

Device collects logic "0" when input signal being grounded.

Mode A: Level application. Alarm outputs high and low level, and the

alarm outlet is OD, which requires external pull-up resistance (10K

Ohm typical) to work. The maximum external pull-up level is 12V,

maximum port current is 300mA and the default output signal is high

level (external pull-up voltage). The default output signal switches to

low level when there is alarm output (As long as the operating current

below 300mA, the output low level voltage is lower than 0.8V).

Step 1

Step 2

Connect alarm output device to the alarm output end of the I/O

port. The alarm output is open-drain output, which works in the

following modes.

Mode B: Switch application. Alarm output is used to drive

external circuit, the maximum voltage is 12V and the maximum

current is 300mA. If the voltage is higher than 12V, please use

an additional electric relay.

Step 3

in alarm setting.

The alarm input in the web interface is corresponding to the alarm

input end of the I/O port. There will be high level and low level

alarm signal generated by the alarm input device when alarm

occurs, set the input mode to "NO" (default) if the alarm input

signal is logic "0" and to "NC" if the alarm input signal is logic "1".

The alarm output in the web interface is corresponding to the

alarm output end of the device, which is also alarm output end of

the I/O port.

Loosen the adjust knob and adjust the camera to a

proper surveillance position as needed.

Secure the adjust knob to fix the camera.

Note: Step 1

Step 2

Step 3

Step 4

Step 5

Drill screw holes on the mounting surface as the

positioning map shows, and then put in the expansion

bolts.

Attach the camera pedestal to the mounting

surface with the self-tapping screws.

Connect the cable and start the camera.

Connecting

Connect alarm input device to the alarm input end of the I/O port.

See the following picture.

Adjust Knob

Self-tapping Screw

Mounting Surface

Positioning Map

Produkt Specifikationer

Mærke:	Imou
Kategori:	Kamera
Model:	Cube PoE

Har du brug for hjælp?

Hvis du har brug for hjælp til Imou Cube PoE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kamera Imou Manualer

Imou Cell PT Lite Manual

8 Januar 2025

Imou Ranger Dual 6MP Manual

14 December 2024

Imou Ranger Dual 8MP Manual

14 December 2024

Imou Ranger Dual 10MP Manual

14 December 2024

Imou Cruiser SC 5MP Manual

11 December 2024

Imou Cruiser SC 3MP Manual

11 December 2024

Imou IPC-T22A Manual

14 September 2024

Imou Cell Go Manual

9 September 2024

Imou Cell Go Full Color Manual

5 September 2024

Imou Cell 3C Manual

3 September 2024

Kamera Manualer

Nyeste Kamera Manualer

17 September 2025

16 September 2025

16 September 2025

16 September 2025

9 Juni 2025

Overmax Camspot 4.8 Manual

9 Juni 2025

Overmax Camspot 4.0 PTZ Manual

8 Juni 2025

Vemer EasyEye.NOW Manual

2 April 2025

Rollei HD-30 Manual

29 Marts 2025

Rollei Security Cam 1080p Manual

29 Marts 2025