Indesit IN2IE14CNP80 Manual
Indesit
Opvaskemaskine
IN2IE14CNP80
Læs nedenfor 📖 manual på dansk for Indesit IN2IE14CNP80 (4 sider) i kategorien Opvaskemaskine. Denne guide var nyttig for 4 personer og blev bedømt med 3.9 stjerner i gennemsnit af 2.5 brugere
Side 1/4
ENQuick Guide
1
CONTROL PANEL
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories:
For information on comparative EN testing conditions, please send an email to the following address:
dw_test_support@europeanappliances.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Values given for programmes other than the eco programme are indicative only. The actual time may vary depending on many factors such as temperature
and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor
calibration. The sensor calibration can increase program duration up to 20 min.
PROGRAMS TABLE
1 2 43
5
1. ON-OFF / Reset button with indicator light
2. Program selection button / Push&GO
3. Salt rell indicator light
4. Program indicator lights
5. START/Pause button with indicator light
Program Programs description
Drying
phase
Duration
of wash
program
(h:min)
*)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
1.
Eco 50°- Eco program is suitable to clean normally soiled tableware, that for this
use, it is the most ecient program in terms of its combined energy and water
consumption, and that it is used to assess compliance with the EU Ecodesign le-
gislation.
4:30 12.0 0.95
2.
Intensive 65° - Program recommended for heavily soiled crockery, especially
suitable for pans and saucepans (not to be used for delicate items).
2:30 16.0 1.50
3.
Mixed - 55° Mixed soil. For normally soiled dishes with dried food residues. 2:25 16.0 1.35
4.
Fast&Clean 28’
45° -
Program to be used for half load of lightly-soiled dishes with
no dried food residues. Does not have drying phase.
-
0:28 9.0 0.60
5.
Push&GO - 50° Everyday wash and dry cycle that ensures great cleaning perfor-
mance in a short time without the need to pre-treat dishes.
1:25 11.5 1.10
PUSH&GO
Push&GO button (P) is an easily distinguishable button that allows you direct access to the Push&GO program, a wash and dry cycle that ensures great
cleaning performance in a short time. You don’t have to worry which program to choose, Push&GO cycle will do the work for you.
To select Push&GO program, switch on appliance, press only button for 3 seconds (corresponding indicator lights up) and close the door within 4 seconds.P
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher and must be
lled when the SALT REFILL indicator light in the control panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Only the rst time you do this: ll the salt reservoir
with water.
3. Position the funnel (see gure) and ll the salt reservo-
ir right up to its edge (approximately 1 kg); it is not
unusual for a little water to leak out.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get into
the container during the wash program (this could damage the water so-
ftener beyond repair).
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle to avoid corrosion.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently
pre-
venting scale buildup on heater, contributing also to better cleaning
eciency.
This system regenerates itself with salt, therefore it is required to rell
salt container when empty.
Frequency of regeneration depends on water hardness level setting - regen-
eration takes place once per 5 Eco cycles with water hardness level set to 3.
Regeneration process starts in nal rinse and nishes in drying phase, be-
fore cycle ends.
• Single regeneration consumes: ~3.5L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid
dispenser A should be lled when when the dark
optical indicator on the dispenser door becoC-
mes transparent.
NEVER pour the rinse aid directly into the
appliance tub.
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device . Introduce the D
detergent into the dry dispenser only. Place the amount of detergent for E
pre-washing directly inside the tub.
Usage of detergent not designed for dishwashers may cause malfunc-
tion or damage to the appliance.
D
E
A
C
FIRST TIME USE
More information in the Daily Reference Guide on website.
THANK YOU FOR BUYING AN INDESIT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.indesit.com/register
PLEASE SCAN THE
QR CODE ON YOUR
APPLIANCE IN
ORDER TO HAVE
MORE DETAILED
INFORMATION
Before using the appliance carefully read Safety and Installation Instructions.
After installation, please remember to remove all transport protection parts from
the dishwasher.
2
UPPER RACK
(loading example for the
upper rack)
Load delicate and light
dishes: glasses, cups, saucers,
low salad bowls.
LOWER RACK
(loading example for the
lower rack)
For pots, lids, plates, salad
bowls, cutlery etc.. Large
plates and lids should ide-
ally be placed at the sides
to avoid interferences with
the spray arm.
FOLDABLE
FLAPS
WITH AD-
JUSTABLE
POSITION
CUTLERY BASKET
The basket is equipped with top
grilles for improved cutlery arrangement.
The cutlery basket should be positioned only at the front of the lower rack.
Knives and other utensils with sharp edges must be placed in the
cutlery basket with the points facing downwards or they must be po-
sitioned horizontally in the tip-up compartments on the upper rack.
More information in the Daily Reference Guide on website.
LOADING THE RACKS
CLEANING AND MAINTENANCE
CAPACITY: 14 standard place-settings
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher does
not ll the water.
All LEDs are
blinking rapidly
No water in the water supply or the tap is
closed.
Make sure there is water in the water supply or the tap running.
The inlet hose is bent.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwa-
sher and reboot.
The sieve in the water inlet hose is clogged;
it is necessary to clean it
After having carried out the verication and cleaning, turn o and turn on the
dishwasher and restart a new program.
Dishwasher nishes
the cycle prematurely.
Drain hose positioned too low or siphoning
into home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check
for siphoning into home sewage system, install air admittance valve if necessary.
Air in water supply. Check water supply for leaks or other issues letting air inside.
Detergent leaks.
Depends on the liquid detergent used and
can be emphasized in case of delay option
is activated.
Small leaks will not cause machine malfunction and can be avoided by changing
liquid detergent type or using tablets.
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues
please contact authorized After-sales Service which contact details can be found in the warranty booklet. Spare parts will be available for a period
of either up to 7 or up to 10 years, according to the specic Regulation requirements.
TROUBLESHOOTING
CLEANING THE FILTER ASSEMBLY CLEANING THE SPRAY ARMS
1
A
2
A
B
3
C
4
In case you nd foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
The lower spray arm may
be removed by pulling it
upwards.
Please scan on your product in order to have more detailed information. the QR code
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.indesit.eu and parts-selfservice.europeanappliances.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-
sales Service, please state the codes provided on your product‘s identication plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model
identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
IEC 436
:
Produkt Specifikationer
| Mærke: | Indesit |
| Kategori: | Opvaskemaskine |
| Model: | IN2IE14CNP80 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Indesit IN2IE14CNP80 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Opvaskemaskine Indesit Manualer
10 Juni 2025
20 Februar 2025
24 Januar 2025
15 Januar 2025
15 Januar 2025
14 Januar 2025
30 December 2025
11 Oktober 2024
22 September 2024
17 September 2024
Opvaskemaskine Manualer
- Opvaskemaskine Jolly
- Opvaskemaskine Fisher Paykel
- Opvaskemaskine Koenic
- Opvaskemaskine Valberg
- Opvaskemaskine Trieste
- Opvaskemaskine PKM
- Opvaskemaskine Cecotec
- Opvaskemaskine Telefunken
- Opvaskemaskine Eurolux
- Opvaskemaskine Sôlt
- Opvaskemaskine Equator
- Opvaskemaskine WhiteLine
- Opvaskemaskine Becken
- Opvaskemaskine ELIN
- Opvaskemaskine Flavel
Nyeste Opvaskemaskine Manualer
11 Juni 2025
11 Juni 2025
10 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
8 Juni 2025