Integra HD-BRX1 Manual

Integra Ikke kategoriseret HD-BRX1

Læs gratis den danske manual til Integra HD-BRX1 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 75 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 38 anmeldelser. Har du et spørgsmål om Integra HD-BRX1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

HDBaseT Receiver

F1711-0SN29355998

* 2 9 3 5 5 9 9 8 *

Instruction Manual

HDB-RX1

1 Screw hole for wall attachment: Fix with the supplied screw for wall

attachment when installing on a wall.

2 12V 1A INPUT jack: When connecting to a device that does not

support Power over Cable

(PoC, refer to the back cover)

, connect the

supplied AC adapter.

3 Power indicator: Lights when the power of this unit is on.

4 HDBaseT jack: Use an Ethernet cable to connect to the HDBaseT

OUT jack on one of our AV receivers to receive video signals, audio

signals, control signals, etc.

• As they are covered with a seal when shipped, remove it when you

use the jack.

• Use one of the following Ethernet cables to connect.

ｰWhen using Power over Cable (PoC, refer to the back cover)

Cat6 (Category 6) cable: AWG23 cable or better, 50 m or less in

length

Cat5e (Category 5e) cable: AWG24 cable or better, 45 m or less in

length

ｰWhen not using Power over Cable (PoC, refer to the back cover

Cat6 (Category 6) cable: AWG23 cable or better, 100 m or less in

length

Cat5e (Category 5e) cable: AWG24 cable or better, 90 m or less in

length

• It is recommended to use shielded single Ethernet cable.

• Do not connect this port to the Ethernet ports of network devices.

5 HDMI OUT jack: Transmit video signals and audio signals with a HDMI

cable connected to a monitor such as a TV or projector.

6 ACTIVE/SERVICE switch: Use in the "ACTIVE" position. ("SERVICE"

is for servicing)

7 RS232 port: Used when connecting to a home control system.

• Use a straight cable.

8 IR IN/OUT jacks: Used when connecting to a multiroom remote control

kit.

• Refer to the instruction manual of the IR receiver for the types of

cables required for connection.

 

 



Part Names

 HDMI

Supported

Deep Color, x.v.Color™, LipSync, 3D, 4K 60 Hz, Extended

Colorimetry (sYCC601, Adobe RGB, Adobe YCC601),

Content Type, HDR

HDCP

Revision 1.4, 2.2

Maximum Video Resolution

4k 60 Hz (YCbCr 4:4:4)

 Output jacks

HDMI OUT : 1

 Other jacks

HDBaseT IN : 1

RS232 : 1 (Path through)

IR IN : 1 (Path through)

IR OUT : 1 (Path through)

 General

Power Supply

AC 100 - 240 V, 50/60 Hz

Power Consumption

11.2 W (AC adaptor)

Dimensions (W × H × D)

205 mm × 35 mm × 89 mm

8-1/16" × 1-3/8" × 3-1/2"

Weight

0.45 kg (1 lb)

• Specifications and features are subject to change without

notice.

• We will not accept responsibility for damage arising from the

connection of equipment manufactured by other companies.

189

205

Unit : mm

What’s in the Box













Main unit (1)



AC adaptor (1)



Cushions (4)



Screws for wall attachment (4)



Label for HDBaseTTM cable (2)



Label for AC adaptor cord (2)

Instruction Manual (this document)





The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo

are trademarks or registered trademarks of HDMI Licensing LLC in the United States

and other countries.

HDBaseT

TM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

ll other trademarks are the property of their respective owners.

Wheninstallingontheoor

When installing on the floor, use the supplied cushions to

help prevent damage to the floor.

 When installing on a wall

Fix this unit with the supplied screws for wall attachment

when installing on a wall.

• Do not attach to the ceiling.

• After attaching, check that the fitting is secure. We accept

no responsibility for damage or injury that arises due to

incorrect attachment.

Printed in Malaysia

Installation Basic& Connections

• Use an Ethernet cable to connect the HDBaseT

TM OUT jack on one of the following of our AV receivers to the HDBaseT jack on this unit to transfer video, audio, and control signals.

(DRX-4/DRX-5/DRX-7/DRX-R1/DRC-R1/DRX-7.1/DRX-R1.1/DRC-R1.1, and models supporting HDBaseT

TM OUT sold in 2018 and thereafter)

• When using one of our AV receivers that supports Power over Cable (PoC), it is also possible to supply this unit with power over the Ethernet cable.

Cushions

Screws for wall

attachment

 RS232 Connections

This is an example of connecting to a home control system with an RS232 cable.

Also read the instruction manual supplied with the connected device.

 IR Connections

This is an example of connection to an IR receiver.

Also read the instruction manual supplied with the connected device.

Home control system TV, etc.

RS232 cable RS232 cable

AV Receiver Ethernet cable