Intellinet 508728 Manual

Intellinet Ikke kategoriseret 508728

Læs gratis den danske manual til Intellinet 508728 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Intellinet 508728, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Installation Manual
Type：
：
：
：：NDR DIN rail power supply（
（
（
（（Series：
：
：
：：NDR-75, 120, 240, 480）
）
）
））
NDR-75-12 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 12V 6.3A
NDR-75-24 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 24V 3.2A
NDR-75-48 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 24V 1.6A
NDR-120-12 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 12V 10A
NDR-120-24 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 24V 5A
NDR-120-48 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 48V 2.5A
NDR-240-24 INPUT: 100-240VAC 2.8A 50/60Hz OUTPUT: 24V 10A
NDR-240-48 INPUT: 100-240VAC 2.8A 50/60Hz OUTPUT: 48V 5A
NDR-480-24 INPUT: 100-240VAC 5.3A 50/60Hz OUTPUT: 24V 20A
NDR-480-48 INPUT: 100-240VAC 5.3A 50/60Hz OUTPUT: 48V 10A
Introduction
NDR is a DIN rail power supply series with an economical price and slim design. Like other Mean Well’s DIN series,
they can be mounted on a TS35 Standard DIN rail.
Installation
（ ）1 Always allow good ventilation clearances, 5mm left and right, 40mm above and 20mm below, around the unit
in use to prevent it from overheating. Also a 10-15 cm clearance must be kept when the adjacent device is a
heat source.
（ ）2 The appropriate mounting orientation for the unit is vertical, the input terminals at the bottom and output on
the top. Mounting orientations other than that, such as upside down, horizontal, or table-top mounting, is not
allowed.
（ ）3 Use copper wire only, and recommended wires are shown as below.
AWG 18 16 14 12
Rated Current of
Equipment (Amp) 7A 10A 15A 20A
Cross-section of
Lead(mm2 ) 0.8 1.3 2.1 3.3
Note: Current each wire carries should be de-rated to 80% of the current suggested
above when using 5 or more wires connected to the unit.
Make sure that all strands of each stranded wire enter the terminal connection and the screw terminals are
securely fixed to prevent poor contact. If the power supply possesses multi-output terminals, please make
sure each contact is connected to wires to prevent too much current stress on a single contact.
（ ）4 Use wires that can withstand temperatures of at least 80°C, such as UL1007.
（ ）5 Recommended wire strapping length is 5mm (0.197”).
（ ）6 Recommended screwdriver is 3mm, slotted type.
Installation Manual
3
12
4
（ ）7 The recommended torque setting for terminals is shown as below.
Model I/P O/P
NDR-75 6.9 kgf-cm (6 Lb-in) 6.9 kgf-cm (6 Lb-in)
NDR-120 7.5 kgf-cm (6.5 Lb-in) 7.5 kgf-cm (6.5 Lb-in)
NDR-240 7.5 kgf-cm (6.5 Lb-in) 7.5 kgf-cm (6.5 Lb-in)
NDR-480 10.35 kgf-cm (9 Lb-in) 10.35 kgf-cm (9 Lb-in)
（ ）8 Suggested fuse and maximum number of the PSUs that can be connected to a circuit breaker at 230V are shown
as below.
Model Fuse Circuit breaker
C16 D16
NDR-75 T3.15A/L250V 6 13
NDR-120 T4A/L250V 5 10
NDR-240 T5A/L250V 4 10
NDR-480 T8A/L250V 3 5
（ ） ：9 Mounting Instruction
Mount as shown in figure only, with input terminals down, or else sufficient cooling will not be possible.
Admissible DIN rail TS35/7.5 or TS35/15 ：
For rail fastening：
（ ）a Tilt the unit slightly rearwards.
（ ）b Fit the unit over top hat rail.
（ ）c Slide it downward until it hits the stop.
（ ）d Press against the bottom for locking.
（ ）e Shake the unit slightly to check the locking action.
（ ）10 For other information about the products, please refer to www.meanwell.com for details.
Warning / Caution !!
（ ）1Risk of electrical shock and energy hazard. All failure should be examined by a qualified technician. Please do
not remove the case of the power supply by yourself!
（ ）2Risk of electric arcs and electric shock (danger to life). Connecting both the primary and the secondary sides
together is not allowed.
（ ）3Risk of burn hazard. Do not touch the unit in operation and shortly after disconnection!
（ ）4 Risk of fire and short circuit. The openings should be protected from foreign objects or dripping liquids.
（ ）5 Only install the unit in a pollution degree 2 environment (Note.1).
（ ）6 Please do not install the unit in places with high moisture or near the water.
"Click"

Produkt Specifikationer

Mærke: Intellinet
Kategori: Ikke kategoriseret
Model: 508728

Har du brug for hjælp?

Hvis du har brug for hjælp til Intellinet 508728 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Intellinet Manualer

Intellinet

Intellinet 791274 Manual

7 Juni 2025
Intellinet

Intellinet 791267 Manual

6 Juni 2025
Intellinet

Intellinet 791342 Manual

31 Maj 2025
Intellinet

Intellinet 714136 Manual

31 Maj 2025
Intellinet

Intellinet 791335 Manual

31 Maj 2025
Intellinet

Intellinet 772211 Manual

31 Maj 2025
Intellinet

Intellinet 713696 Manual

31 Maj 2025
Intellinet

Intellinet 715584 Manual

31 Maj 2025
Intellinet

Intellinet 790789 Manual

31 Maj 2025
Intellinet

Intellinet 715430 Manual

31 Maj 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet

Planet XGPN-100 Manual

15 Juni 2025
Proficook

Proficook PC-EKA 1283 Manual

15 Juni 2025
OmniMount

OmniMount OBSP8 Manual

15 Juni 2025
Levenhuk

Levenhuk FS10 Manual

15 Juni 2025
Vestil

Vestil PM4-2148-LP Manual

15 Juni 2025
ElectriQ

ElectriQ STRV-W1-B Manual

15 Juni 2025
Adler

Adler AD 4521 Manual

15 Juni 2025
AMX

AMX HydraPort HPX-AV102 Manual

15 Juni 2025
Hughes & Kettner

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025
Hughes & Kettner

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025