Interlogix TX-E721 Manual

Interlogix Bevægelsesdetektor TX-E721

Læs gratis den danske manual til Interlogix TX-E721 (4 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Interlogix TX-E721, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

P/N - 1 4 466 5305 • Rev A • 11APR17 /

TX-E721 Fresnel Lens Pet Immune PIR

Description

This is the Installation Sheet for the TX-E721 Fresnel Lens Pet Immune PIR

A motion sensor (passive-infrared or PIR) detects movement within a

speciﬁc area by sensing the infrared energy emitted from a body as it

moves across the sensor’s field of view. When this motion is detected, the

sensor transmits an alarm signal to the control panel.

Figure 1 Pet Immune SAW PIR Motion Sensors :

Use these motion sensors to protect locations where door/window sensors

are impractical or not needed. For example, use a motion sensor to protect

large areas or open ﬂoor plans. Motion sensors also provide backup

protection for door/window sensors.

The Pet Immune -E721 utilizes advanced signal processing, a new TX

custom designed lens, and a new custom designed sensing element. The

combination of these improvements provides false alarm immunity for pets

with a combined weight of up to 40 pounds while still providing superior

human catch performance.

These wireless motion sensors include the following features:

• 35 by 40 ft. (10.6 m by 12 m) coverage area.

• Three minute transmitter lockout time after an alarm that helps extend

battery life.

• Cover-activated tamper

• Supervisory signals transmitted every 64 minutes to the control panel.

• Sensor low battery reports (trouble) to the control panel.

• Field-selectable sensitivity options.

Installation

Installation Guidelines

• Temporarily place the sensor in its intended mounting location.

Program and ﬁnal test the sensor before permanently mounting it.

• If possible, locate sensors within 100 ft. (30.5 m) of the panel. While a

transmitter may have a range of 500 ft. (152 m) or more out in the

open, the environment at the installation site can have a signiﬁcant

eﬀect on transmitter range. Sometimes a change in sensor location

can help overcome adverse wireless conditions.

• The recommended mounting height is 7 1/2 ft.

• Position the sensor to protect an area where an intruder would be most

likely to walk across the detection pattern See Figure 2.

Figure 2: Overhead Detection Path

• Mount the motion sensor on a rigid surface which is free from

vibrations.

• Do not mount the sensor near duct work or other large metallic

surfaces which may aﬀect the RF signals (see RF Testing). Actual

acceptable transmitter range should be veriﬁed for each installation.

• Mount the sensor permanently on a ﬂat wall or in a corner. Do not set it

on a shelf.

• Windows should be closed in any area which has an armed motion

sensor.

• The sensor must be incline-mounted at a mounting height of 7.5 ft. See

Figure 3.

Figure 3: Wall Mount Options

• Room temperature must be kept between 60° and 120°F (16° and 49°

C).

• Position the sensor so it faces a solid reference point, like a wall.

Programming

Refer to the panel documentation for information on programming the

sensor into the panel.

To Trip the Sensor

1. Set the panel to program mode.

2. Proceed to the Learn Sensors menu.

2 4 -E721 PET Immune PIR Motion Detector Installation Sheet/ TX

3. Remove the PIR from its mounting plate (activating the tamper switch).

4. Select the appropriate sensor group and number.

5. Exit the panel’s programming mode.

6. Return the PIR to its mounting plate.

Final Testing

Final testing should be done to verify radio signal integrity and conﬁrm

control panel programming and response. The actual transmitter range can

be determined by performing a sensor test as follows:

1. With the PIR temporarily mounted at its intended location, remove the

PIR from its mounting plate and activate the tamper switch to start the

walk test mode.

2. Replace the sensor in its mounting plate.

3. Place the control panel in Sensor test mode. Move across the

detection pattern until the sensor’s LED turns on. STOP your motion.

4. Listen for the appropriate system response. Refer to the speciﬁc panel

installation manual for details on system response. If the system does

not respond as expected, proceed to the section. “ ”Troubleshooting

Mounting

The sensors must be incline-mounted on a wall surface or incline-mounted

in a corner at a mounting height of 7.5 ft. (2.5 m).

To Mount the Sensor

1. Remove the mounting plate by depressing the button on the top of the

sensor body. With the opposite hand pull the mounting plate away from

the body of the sensor.

2 Punch out the mounting holes that best ﬁt your application. See Figure

3 for wall mount options.

3. See Figure 4 to determine which knockouts to use when mounting the

motion sensor. Use the outside 4 holes for corner mounting, or the

inside 4 holes for surface mounting.

Figure 4: PIR Mounting Plate Knockouts

4. Mark the location of the required holes on the mounting surface.

5. Use wall anchors and screws to secure into place. Attach the sensor to

the mounting plate.

6. When testing is completed the PIR can be securely attached to its

mounting plate by screwing the smallest enclosed screw into the hole

at the top of the mounting plate.

Setting the Sensitivity

The PIR has two sensitivity settings (standard and high sensitivity). The

sensor is set to standard sensitivity at the factory. This sensitivity is

preferred for most applications and provides the best immunity to false

alarms.

Note: If the shorting jumper is not used or is placed incorrectly, the sensor

defaults to standard sensitivity.

Figure 5: Sensitivity Pin Locations

CAUTION: High sensitivity should only be used in environments where

the room temperature is very stable.

ATTENTION: La haute sensibilité ne doit être utilisée que dans des

environnements où la température ambiante est très stable

1. Remove the mounting plate by depressing the button on the top of the

sensor body. With the opposite hand pull the mounting plate away from

the body of the sensor.

2. Locate the sensitivity pins directly above the battery when looking at

the back of the PIR

3. To change to high sensitivity, move the shorting jumper to the pair of

pins that are closer to the left side of the PIR

4. Walk test the PIR to verify the sensitivity.

The diﬀerence between the two settings are indicated in Figures 6 and

7.below.

Figure 6: Standard Sensitivity Setting

Figure 7: High Sensitivity Setting

Produkt Specifikationer

Mærke:	Interlogix
Kategori:	Bevægelsesdetektor
Model:	TX-E721

Har du brug for hjælp?

Hvis du har brug for hjælp til Interlogix TX-E721 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Interlogix Manualer

Interlogix TX-E721 Manual

24 Juli 2024

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Optex AX-200TF Manual

10 August 2025

10 August 2025

10 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

Vemer Muvy DUO Manual

4 August 2025

Theben thePassa P360 KNX UP Manual

3 August 2025

Theben theRonda P360 DALI-2 HCL UP Manual

3 August 2025