Intermatic RC2163BFE Manual

Intermatic Fjernbetjening RC2163BFE

Læs gratis den danske manual til Intermatic RC2163BFE (2 sider) i kategorien Fjernbetjening. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Intermatic RC2163BFE, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Because of our commitment to continuing research and improvements, Intermatic Incorporated reserves the right to make changes, without notice, in the specifications and material
contained herein and shall not be responsible for any damages, direct or consequential, caused by reliance on the material presented.
INTERMATIC INCORPORATED, SPRING GROVE, IL 60081-9698
http://www.intermatic.com
158AS11682
RC2000 SERIES
REMOTE CONTROLS
INSTALLATION
OPERATION &
SERVICE MANUAL
Model: RC2163FE Control Center / Model: RC2163BFE Control Panel
REMOTE OPERATED CONTROLS FOR POOL - SPA COMBINATIONS
In Rainproof (Type 3R) Enclosure Suitable for Pool/Spa Equipment Control and for Direct Connection of Underwater Lights
ELECTRICAL RATING: 20 A Resistive - 120V or 240V, 1.5 HP - 120V, 3 HP - 240V, DPST
LOW VOLTAGE: 24V - 40 VA Maximum
Many of today’s pools and spas utilize the advantages of a
single electrical control panel, containing all the necessary
components for the safe, cost effective and automatic
operation of a pool or spa.
Model RC2163FE is designed to operate the shared
equipment, like the filter pump, filter and the heater of a
Pool-Spa combination safely from the spa side or other
remote location.
The 24 hour timer turns ON the filter pump and
automatically filters and, if set, heats the pool water on a
daily schedule. In addition, the control provides a 120 volt
and a 24 volt output for a switching device (a toggle switch,
a timer or a radio receiver) installed at a convenient remote
location in order to turn ON the pump, the heater and rotate
the valves thus allowing the water to circulate in the spa.
The Control also features a three position selector switch
for the heater.
The Control also has terminals to accept a number
of options like the freeze or heater protection accessories.
Model RC2163BFE is the same as the one described
above, except it is built into an 8 circuit 100 Amp.
sub-panel.
The Control coordinates the operation of the various
equipment according to the following table:
Sequence 1 Sequence 2
EQUIPMENT POOL MODE SPA MODE
Filter Pump Timer Controlled ON - Continuously
Heater If selected, Water Temperature Water Temperature
is as Set by Pool Thermostat is as Set by Spa Thermostat
Valves Set to Pool Circulation Set to Spa Circulation
1
DANGER! To Reduce the Risk of Injury:
...do not permit small children to operate the control or use the Pool/Spa unless they are closely supervised at all times.
...test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA! Contact a service technician.
...always disconnect electricity before servicing this Control or the equipment connected to it. THIS CONTROL IS NOT TO BE
USED AS A POWER DISCONNECT.
READ, FOLLOW & SAVE THIS INSTRUCTION MANUAL
GENERAL INFORMATION
4
WIRING DIAGRAM RC2163FE
Single Thermostat Heater
Dual Thermostat Heater
1. Connect two 18 gauge wires in
with Heater’s Selector SERIES
Switches.
2. Connect one of the wires to
terminal “C” and the other to
terminal “L”. INSTALL JUMPER
BETWEEN TERMINALS
“L” AND “H”.
3. Leave heater switch in position.ON
1. Connect three 18 gauge wires in
with Heater’s Selector PARALLEL
Switches.
2. Connect the wire from central post
(Common) of heater switch to
terminal “C”, High to “H” and
Low to “L”.
3. Leave heater switch in position.OFF
120V Pump NEUTRAL WHITE and NEUTRAL - Connect to lead pump .
Connect 120V. line to lead and lead to pump terminal.BLACK BLUE LOAD
Cap and leads.RED YELLOW
ONE YEAR LIMITED WARRANTY
If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace
it, at its sole option, the unit free of charge. This warranty applies only to the original purchaser and is not transferable. This warranty does not apply
to: (a) damage caused by accident, abuse, mishandling, dropping, acts of God, or any negligent use; (b) units which have been subject to unauthor-
ized repair, opened, taken apart, or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the
product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you. This warranty gives you specific legal
rights and you may have other rights that vary from state to state.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER
EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE
OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product,
along with proof of purchase, postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/
After Sales Service, 7777 Winn Rd., Spring Grove, IL 60081-9698/815-675-7000 http://www/intermatic.com Please be sure to wrap the product
securely when mailing to avoid shipping damage.
RC2163BFE
RC2163FE
MEMORY
HOLD-UP
BATTERY
TIMER
NEUT.
LINE
120/24V.
TRANSFORMER
HEATER
SELECTOR
SWITCH
PUMP RELAY 120V.
SUPPLY
REMOTE
LOCATED
RADIO
RECEIVER
ORG
BLK
WHT
RED
BRN
24 V
SENSOR
BRN
REMOTE
LOCATED
120V SWITCHING
DEVICE*
BLK
WHT
120 VOLT
PC BOARD
24 VOLT
PC BOARD
LINE 2
LOAD 2
LOAD 1
LINE 1
240V.
SUPPLY/LOAD
CONNECTIONS
NEUT. WHITE
LINE BLACK
120V.
SUPPLY
120 VOLT
SENSOR
CONTROL
SUPPLY
*Use either the 120V or the 24V remote
sensor connection. Insulate (cap) the
other line(s).
SENSOR RELAY
24 V
SWITCH*
24 V A C
STEP TRANS S W 1
158AS11682 1 3/18/09 4:24:41 PM
INSTALLATION RC2163FE
SETTINg / OPERATINg INSTRUCTIONS
This Control can operate either a 120 volt or 240 volt, single speed pump, together with a gas heater and up to three
24 volt valve actuators. It has a 120 volt and 24 volt connection for a remote installed switching device and also has
a connection for a freeze or heater protection device to turn ON the pump if needed.
IMPORTANT: High and low voltage conductors should not occupy the same conduits or compartments.
2
1. Follow wiring diagram on Page 4 and prepare your
installation layout. Make sure only copper (solid or
 stranded),70˚Cminimumratedconductorsareused,
properly sized and suitable for the installation. Each
piece of equipment must be grounded properly.
IMPORTANT: Neutral must always be connected
to the white lead of the control.
2. Hang Control on a flat vertical surface or other
support, using hardware suitable for the purpose.
3. Prepare the necessary conduit runs, including one
for the remote - located 120 volt switching device
(switch, timer or radio receiver), underwater light(s),*
terminate them at both ends and pull-in the
conductors as specified by the installation layout.
*If this control is to be used for direct connection
to under-water lights, a Nonmetallic Hub Kit
should be used. Order 156PA13713A for a 1/2”
Kit, 156PA13714A for a 3/4” Kit or 156PA13715A
for a 1” Kit.
4. Follow wiring diagram on page 4, make LINE and
LOAD (Pump) connections in the high voltage
compartment.
Make sure the installation is securely grounded and
bonded if required.
5. Remove screw next to Heater Switch and gain
access to printed circuit (P.C.) board assembly in
low voltage compartment. Follow wiring diagram on
page 4, plug valve actuators into designated sockets
on P.C. board and make heater connections to ter-
minals 1, 2 and 3.
Place jumper between terminals L and H if heater
is single stage. See page 4 for details. Replace
P.C. board assembly.
6. If selected, install remote - located low voltage control
(Switch, or Timer). See wiring on page 4.
7. Check wiring, tightness of connections and
grounding.
Close wiring compartment and test installation.
8. Set timer, see instructions below.
SETTINg/OPERATINg INSTRUCTIONS (Continued) RC2163FE
3
To Review Program: Press TIMER key repeatedly.
When done, press CLOCK key to return to the time
of day.
To Cancel/Change Part of the Program: Press Timer
key repeatedly until the particular ON or OFF time
appears. Set new ON or OFF time.
To Override the Automatic Operation one time:
Press OVR. key to turn ON/OFF equipment.
NOTE: Timer will resume automatic operation with the
next opposite setpoint.
To Suspend Automatic Operation Permanently:
Press SELECT key to move indicator bar to the desired
ON or OFF position. Note: Timer will not resume auto-
matic operation until indicator bar is repositioned above
the word AUTO.
IMPORTANT SAFETY INSTRUCTIONS
When installing and operating this Product and other associated equipment, basic safety precautions should always be followed,
including the following:
1. Read and follow all instructions.
2. This Control must be installed by a qualified electrician, according to National and Local Electrical Codes.
3. Install this control not less than 5 feet (3 meters in Canada) from inside edge of pool and 1 foot (30 cm) above ground. USE
COPPER CONDUCTORS ONLY, rated Min. 70˚C.
4. Do not exceed the maximum ratings of individual components, wiring devices, and current carrying capacity of conductors.
5. For Control grounding, bonding, installing and the wiring of underwater lights, refer to Article 680 of the National Electrical Code or Article
68 of the Canadian Electrical Code.
6. The Control should not operate any equipment which would cause bodily injury or property damage should it be activated
unexpectedly.
READ, FOLLOW AND SAVE THIS INSTRUCTION MANUAL
Indicator LED “ON”
when connected to
power source and
contacts are closed
Display
Reset port
to cancel all
prior settings
ON/AUTO/OFF
Select Key
Function Keys
Programming Instructions
To Set or Change the Time of Day: To clear entire
memory, press key. Hold down the CLOCK key
while pressing either the HOUR or MINUTE keys.
Continue pressing until the desired number is shown.
Then simply lift finger off the CLOCK key to set.
To Set Program (ON/OFF times): Press TIMER key
once to enter into program mode. Display will show
“1 ON-- --”. Press the HOUR key and then the
MINUTE key to select the desired first ON time. Press
TIMER key once. Display will show “1 OFF -- --”.
Repeat previous step to select the desired first OFF
time. Repeat the entire sequence to complete up to
eight total ON/OFF times as desired. When program-
ming is done, press the CLOCK key then the SELECT
key repeatedly until the indicator bar is above the word
“AUTO”.
To Operate Equipment in Spa Mode:
1. Activate control.
2. After using the spa, make sure that control is
back in the POOL mode.
To Operate Heater:
Heater Selector Switch is provided to save on heating
cost during the summer months or prevent over-heat-
ing of pool water if heater is the single thermostat type.
Set switch to POOL AND SPA mode if the heater is the
DUAL thermostat type and set thermostats on heater
to the desired pool and spa water temperatures.
Set switch to SPA ONLY mode if the heater is the
SINGLE thermostat type or only the spa water needs
to be heated. Set switch to OFF if no heater operation
is needed.
ENCLOSURE DETAILS
TROUBLESHOOTINg
Symptom Possible Cause(s) Corrective Action
Control will not operate Defective remote control Replace remote control
in SPA mode Defective relay Replace relay
Blown fuse Replace fuse
Timer is not turning Defective timer Replace timer
pump ON/OFF for Defective relay Replace relay
daily filtration Timer is set to ON/OFF Set timer to AUTO
No program in memory Set program - see instructions
Dead battery Replace battery
Valve actuators(s) is/are Frozen valve Check/Lubricate valve
not working Defective actuator Replace actuator
Loose connection Check connections
Blown fuse Replace fuse
Pump inoperative Open circuit breaker Check power supply
Defective relay Change relay
Defective pump Check pump
RC2163BFE RC2163FE
158AS11682 2 3/18/09 4:24:42 PM

Produkt Specifikationer

Mærke: Intermatic
Kategori: Fjernbetjening
Model: RC2163BFE

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic RC2163BFE stil et spørgsmål nedenfor, og andre brugere vil svare dig


Fjernbetjening Intermatic Manualer

Intermatic

Intermatic RC-LRSR-WH Manual

30 Januar 2025
Intermatic

Intermatic RC613L Manual

30 Januar 2025
Intermatic

Intermatic RC613R Manual

30 Januar 2025
Intermatic

Intermatic RC2163BFE Manual

30 Januar 2025
Intermatic

Intermatic RC2343PT Manual

30 Januar 2025
Intermatic

Intermatic RC613 Manual

30 Januar 2025
Intermatic

Intermatic RC939 Manual

30 Januar 2025

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Philips

Philips Prestigo SRU8010 Manual

15 August 2025
Philips

Philips CP0118 Manual

14 August 2025
Renkforce

Renkforce RF-PLP-202 Manual

14 August 2025
Renkforce

Renkforce RF-5253052 Manual

14 August 2025
Renkforce

Renkforce RF-WRC-300 Manual

14 August 2025
Renkforce

Renkforce RF-PLP-200 Manual

14 August 2025
One For All

One For All EazyClean URC 9290 Manual

13 August 2025
One For All

One For All URC 2781 Manual

13 August 2025
One For All

One For All Digital 5 URC 7557 Manual

12 August 2025
Chamberlain

Chamberlain CH382C Manual

12 August 2025