Intermatic WP1030MXD Manual

Intermatic Ikke kategoriseret WP1030MXD

Læs gratis den danske manual til Intermatic WP1030MXD (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Intermatic WP1030MXD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

WP1000MX SERIES

WEATHERPROOF RECEPTACLE COVERS

FOR EXTRA-DUTY APPLICATIONS

Single-gang horizontal

Model WP1010HMXD

Single-gang vertical Model

WP1010MXD, WP1250MVXD and

WP3110MXD

A grounding wire is provided for all models. The mounting screw that holds the receptacle or light switch should pass through the ring terminal on the end of the wire.

Double-gang Model WP1030MXD and

WP1250MXD

This double-gang cover is designed for installation on double-gang junction

boxes. If installing on a non-metallic junction box, you will need to use the

grounding wire (as shown on the Optional Grounding illustration). If the junction

box is non-metallic, a separate ground will need to be run and connected to

the grounding wire by cutting and removing the spade terminal, stripping

the ground wire and making a pigtail connection. Also note for single-gang

installation you will need to purchase an Intermatic insert model #WP101 for

duplex receptacle or WP102 for GFCI application.

The insert for model WP1030MXD and WP1250MXD may be oriented for

horizontally or vertically mounted receptacles and is designed for double duplex

or double GFCI applications.

This die cast cover can be used outdoors or in other wet locations when cover

is closed (protects receptacles while in-use for unattended applications).

The cover is UL Listed, rated Type 3R and meets National Electrical Code

requirements covered by Article 406.9 (B)(1).

Contents

The following items are included:

• Weatherproof cover/base - pre-assembled.

• Universal insert for duplex receptacles (model WP1030 includes a double

duplex insert)

• Universal insert for GFCI receptacles (model WP1030 includes a double GFCI

insert)

• Gasket with slits for mounting screws

• Baggie assembly with mounting hardware

Models

The instructions cover these models:

WP1010MXD, WP1250MVXD, WP3110MXD

Single-gang vertical mounting only

WP1010HMXD

Single-gang horizontal mounting only

WP1030MXD, WP1250MXD

double-gang, 2 device installation

Installation

Follow the steps listed below, while referring to the illustrations for your

particular model.

1. If installation is being done on an existing receptacle(s), remove the

existing cover and discard.

2. The mounting screws that hold the receptacle or GFCI to the junction box

can be removed. Do not remove the receptacle wiring connections.

3. Select the correct insert for your application and press into base.

4. Locate the gasket as required for the installation. The gasket can be

temporarily held to the back of the base/insert assembly using the

mounting hardware provided. The receptacle cover should be installed on a

smooth, flat, non-porous surface.

To ensure a weatherproof seal on irregular surfaces such as brick or cedar

siding, a 1/4" bead of non-hardening silicon caulk compound (neoprene,

urethane or polyurethane type) should be placed between the weather-

proof receptacle gasket and the mounting surface.

5. Mount the base/insert assembly and the receptacle(s) to the junction box

using two of the long screws provided (do not over-tighten).

To ensure weatherproof protection, the cover must be installed so that the

hinge points are located at the top.

6. If mounting to an outdoor junction box or FS box, use the remaining long

screws, 2 or 4 screws as required, to further secure the cover and insert

assembly to the junction box. Note that holes are located in the insert for

mounting to an FS box or any standard single-gang box. For specially

designed junction boxes, holes should be carefully drilled to line up with

the holes in the box to accommodate mounting.

7. Be sure all screws are secure but not over-tightened. Install the remaining

1 or 2 short screws into the receptacle(s) as required.

8. A hasp is provided to allow for padlocking the cover if desired.

FOR BEST PROTECTION FROM RAIN OR HUMIDITY, BE SURE TO ROUTE THE

CORDS THROUGH THE CORD OUTLETS IN THE COVER AND PRESS THE COVER

FIRMLY UNTIL IT SNAPS CLOSED OVER THE HASP.

Cover may be removed for ease of mounting and then reattached.

Optional Grounding

(Single gang

installation)

Optional

Grounding

WARNING

• Disconnect power at the circuit breaker(s) or disconnect switch(es) before

installing or servicing.

• KEEP COVER CLOSED when used in wet locations.

Risk of Fire or Electric Shock

NOTICE

• If using a power screwdriver, be careful not to over-tighten the screws

in the junction box and/or the electrical device to prevent stripping the

threads.

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	Ikke kategoriseret
Model:	WP1030MXD

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic WP1030MXD stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Intermatic Manualer

Intermatic EK4536 Manual

12 November 2025

Intermatic LC4521C Manual

11 November 2025

Intermatic OP2GY24 Manual

8 November 2025

Intermatic OP2BK24 Manual

6 November 2025

Intermatic WP1010HMXD Manual

6 November 2025

Intermatic WP1250MXD Manual

5 November 2025

Intermatic OP2BK18 Manual

4 November 2025

Intermatic WP1030MXD Manual

4 November 2025

Intermatic OP5BK24 Manual

4 November 2025

Intermatic OP5GY24 Manual

4 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Televés NevoSwitch 714609 Manual

21 December 2025

Reznor UBZ-30 Manual

21 December 2025

Delta RP31845 Manual

21 December 2025

Duravit L-Cube LC624204040 Manual

21 December 2025

WAC Lighting LTK-725 Manual

21 December 2025

IFM EBF026 Manual

21 December 2025

IFM PG1405 Manual

21 December 2025

WAC Lighting HT2 Manual

21 December 2025

Vevor QYP72IN Manual

20 December 2025

WAC Lighting H-1023F Manual

20 December 2025