Jabsco 37010-1096 Manual

Jabsco Toilet 37010-1096

Læs gratis den danske manual til Jabsco 37010-1096 (4 sider) i kategorien Toilet. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Jabsco 37010-1096, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Model 37010-Series

ELECTRIC MARINE TOI LET

Push Button Operation

FEATURES

• White Vitreous China Bowl Available in Two Sizes

• Baked enamel seat & cover -

soft close seat option available on regular bowl models

• Flexible Impeller Flush Pump

• Permanent Magnet Type Motor, Fully Enclosed, with

Stainless Steel Shaft

• High Capacity Waste Macerator and Bowl discharge Pump

• Built-in Back Flow Preventer

•

Corrosion resistant material for marine use

ARIATIONS

MODEL NUMBER DESCRIPTION

37010-3092 Compact Bowl 12V

37010-3094 Compact Bowl 24V

37010-4092 Regular Bowl 12V

37010-4192 Regular Bowl 12V, Soft Close Seat/Lid

37010-4094 Regular Bowl 24V

37010-4194 Regular Bowl 24V, Soft Close Seat/Lid

INSTALLATION

The Jabsco electric toilet may be installed above or below

the waterline. Flush pump is self-priming with a vertical lift

up to 4 feet; discharge macerator pump can operate

against a vertical head up to 4 feet (1.2m).

Inlet and outlet seacocks should be easily accessible and

be positive shut off valves. If seacocks cannot be con ve -

nient ly operated from toilet location, install suitable shut off

valves for inlet and discharge connections.

Base assembly may be moved 90° to accommodate con -

nec tions and provide accessibility for servicing.

Surface where toilet is mounted should be flat to prevent

distortion of toilet base.

PLUMBING CONNECTIONS - Connect inlet hose using

3/4" (19mm) ID hose. Make sure all inlet connec-tions

are airtight and free of sharp bends or restrictions.

Do not connect the toilet to the vessels

potable water for its source of supply. To do so can result in

contamination of potable water supply. If fresh water is pre-

ferred for flushing, provide a separate fresh water tank to

supply water to the toilet only.

DO NOT CONNECT INLET HOSE TO A PRESSURIZED

WATER SYSTEM.

Flood hazard. If toilet is installed below the

waterline or may be below the waterline at any

angle of heel or trim, it must be installed with

properly positioned vented loops. Failure to do

so can result in flooding which can cause loss

of property and life.

WARNING

CAUTION

Connect 1" (25mm) or 1-1/2" (38mm) hose to

discharge hose to discharge port (Adaptor 98023-0080 is

included to convert discharge port to 1-1/2"ID hose),

and make suitable connection to holding tank

orother discharge system. Avoid sharp bends or

restrictions.For above waterline installations, a check

valve may haveto be instal-led in the flush water intake

line to ensure rapidpump priming. To retain water in

bowl, make a loop in the dischar ge line about 8 inches

(200mm) above base of bowl.

If the toilet is, or can be, below waterline at any normal(in-

cluding static) attitude of vessel heel and/or trim, a 3/4"

(19mm) Vented Loop Fitting must be installed in the

length of hoseconnecting the flushing pump to the inlet

seacock. TheVented Loop Fitting must be positioned so it

remains at least 8" (200mm)* above the waterline at all

angles of heel and trim.In some installations when a

vented loop is installed in theintake hose, the flushing

pump primeability and flow char-acteristics are reduced

and may adversely affect toiletfunction. To restore

pump performance, connect a solenoid valve

(Jabsco No. 37068- 000) to the vent air inlet to 2

inter-rupt the air supply during the flush cycle. The

brass port ofthe solenoid valve (remove plastic filter if

attached)shouldbe connected to the vent inlet with

3/16" hose and thesole-noid wired in parallel with the

toilet motor. See diagram below.

ELECTRICAL CONNECTIONS - Select a location for

the switch and instruction plate, making sure wire leads

from both the toilet and power source can be routed to

the switch. Ensure the panel where installing switch is no

more than 1" thick. Drill a 5/8" mounting hole and install

switch and instruction plate. Use stranded copper wire of

the correct size (determined from the electrical specifi-

cations chart) to connect one side of the switch to the

positive power source. An appropriate size fuse or equiv-

alent circuit breaker (determined from electrical specifi-

cations chart) must be installed in the positive power

lead within seven inches of the power source. Connect

the other side of the switch to the orange (positive) motor

lead. Connect the black (negative) motor lead to the neg-

ative side of the battery or grounded buss bar.

NOTICE: Correct motor polarity (orange to positive,

black to negative) is important. Reverse polarity can

damage motor and void warranty. Full voltage at the

motor is required to properly operate the Electric Toilet.

The toilet must be wired in a circuit independent of all

other accessories.

ELECTRICAL SPECIFICATIONS

AMP FUS E WIRE SI ZE PER FEET OF RU N*

V OLTA G E DRAW S IZE 0'-10' 10'-15' 15'-25' 25'-40' 40'-60'

12 Vdc 16 25 #12 #10 #10 #8 #6

24 Vdc 8 15 #16 #14 #12 #10 #10

* Length of run is total distance from power source to product and back to ground.

OPERATING INSTRUCTIONS

Make sure inlet and outlet seacocks are all open; push button

to operate. Operate until bowl is completely flushed and

discharge pump has scavenged water from bottom of bowl.

The Jabsco electric marine toilet will provide years of trou-

blefree service if properly used. It will handle waste and toi-

let tissue. It will NOT handle rags, sanitary napkins or hard

solid objects.

If bowl does not pump out and begins to fill, partially close

inlet valve until bowl is cleared and completely pumped

out. Then operate for a few seconds with both valves open

to clear entire toilet and discharge system. For maximum

safety, when toilet is not in use or vessel is unattended,

close both the inlet and discharge seacocks.

To drain for winter lay-up, close inlet valve and operate for

a few seconds until all water is pumped out.

After long periods of non-use, toilet and pump may dry out.

To ease initial start-up, put about one quart of water in bowl

and let stand awhile before initial use.

DISASSEMBLY

Disconnect pumping inlet and discharge hoses. Remove

four screws, Key No. 25, pull out com plete motor, pump

and macerator assembly. If assembly does not slide out

easily, push forward and pull back sharply several times to

free macerator housing from base.

Remove discharge port, Key No. 12, and joker valve.

Unscrew chopper plate, Key No. 14, by turning counter -

clock wise, facing plate. Prevent shaft from turning by plac-

ing screwdriver in discharge port and locking centrifugal

impeller blade. Remove macerator housing. Loosen

impeller set screw and slide impeller off motor shaft.

Remove four flathead screws and two washers, Key Nos.

20, 21, & 22. Remove the plastic wear plate, Key No. 23,

with sealing sleeve, Key No. 19, and gasket, Key No. 26.

Slide pump assembly off motor shaft. Replace all worn or

damaged parts, clean remaining parts.

ASSEMBLY

Press seal into body with lip facing impeller; be careful

not to cock seal in bore. Install pump body on motor and

position on register. Lubricate impeller bore with pump

grease and install impeller. Position the gasket against

the body and install the wearplate ensuring the two plas-

tic sealing washers are under the heads of the top and

bottom screws. NOTE: The current plastic wearplate

supercedes the earlier brass wearplate and with it the

stainless steel wearplate is no longer used. Slide the

rubber sealing sleeve on the motor shaft and push it into

its recess in the wearplate. Relocate centrifugal impeller

on shaft, about 1/8" from the wearplate, and tighten set

screw. Place macerator housing over shaft and centrifu-

gal impeller, put lock washer on end of shaft and screw

chopper plate on shaft and tighten. Install O-ring in O-

ring groove in wearplate surface, a little grease will help

hold in place, make sure inside body surfaces are clean,

line up slot in base with key on macerator housing, slide

pump assembly into base and tighten with the four

screws. Turn motor on for one or two seconds to be sure

centrifugal impeller is free.

WARNING

!Flood hazard. Close inlet and outlet

seacocks prior to disassembling toilet.

Failure to do so can result in flooding

which can cause loss of property and life.

37068-0000

SOLENOID

Produkt Specifikationer

Mærke:	Jabsco
Kategori:	Toilet
Model:	37010-1096

Har du brug for hjælp?

Hvis du har brug for hjælp til Jabsco 37010-1096 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Toilet Jabsco Manualer

Jabsco 37010-1096 Manual

12 August 2024

Jabsco 29120-2000 Manual

25 Juli 2024

Jabsco 29090-2000 Manual

29 November 2022

Toilet Manualer

Nyeste Toilet Manualer

Thetford SK220 Manual

2 Oktober 2025

Thetford SK260 Manual

2 Oktober 2025

Liberty Pumps Ascent II-RSW Manual

16 September 2025

Liberty Pumps Ascent II Manual

16 September 2025

PolyJohn PJN3-1007 Manual

27 August 2025

PolyJohn PJN3-1122 Manual

27 August 2025

PolyJohn PJG3-1013 Manual

26 August 2025

PolyJohn PJG3-1004 Manual

26 August 2025

PolyJohn PL01-1000 Manual

26 August 2025

PolyJohn PJN3-1008 Manual

25 August 2025