Jabsco 29120-2000 Manual

Jabsco Toilet 29120-2000

Læs gratis den danske manual til Jabsco 29120-2000 (5 sider) i kategorien Toilet. Denne vejledning er vurderet som hjælpsom af 54 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 27.5 anmeldelser. Har du et spørgsmål om Jabsco 29120-2000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Models 29090-2000

29120-2000

MANUAL MARINE TOILET

FEATURES

• Easy to clean white ceramic bowl

• Sturdy wood seat with durable baked enamel finish

• Forward angled pump for easy operation

• Convenient top-mounted dry bowl selector

• Reversible pump mounting for right or left hand

installation

• External seal housing/rod guide for easy replacement

• Extra large seal housing allows piston rod assembly to

be removed without removing valve cover

• Smooth external surfaces with skirted base to maintain

cleanliness

• Base of pump and valve cover are skirted to conceal

gasket/flap valves

• Triadic full-flow joker valve to avoid accidental blockage

• Multi-angle discharge port for versatility of plumbing

connection

VARIATIONS AVAILABLE

MODEL NO. DESCRIPTION

29090-2000 Compact Size Bowl & Seat

29120-2000 Household Size Bowl & Seat

SPECIFICATIONS

Inlet port – 3/4"

Disharge port – 1-1/2"

Weight – compact bowl: 26 lb

large bowl: 32 lb

APPLICATION

The Jabsco Manual toilet is designed to meet the require-

ments of onboard marine applications. It may be installed

above or below the waterline. If the toilet is, or can be,

below the waterline at any normal (including static) attitude

of vessel heel and/or trim, a 3/4" Vented Loop Fitting must

be installed in a length of hose that connects the flushing

pump to the rear of the bowl. The vented Loop Fitting

should be positioned so it remains about eight inches or

more above the waterline at all angles of heel and trim. If

the toilet is plumbed to an overboard discharge, the

discharge hose must also include a Vented Loop Fitting.

(See WARNING.) The toilet may be plumbed so waste is

Models 29090-2000 & 29120-2000

discharged to holding tank, directly overboard (where

permitted by law) or into a certified waste treatment device.

For installation versatility, the pump assembly may be

positioned on the left or right hand side of the bowl. Its

multi-angle discharge port will allow routing of discharge

hose in almost any direction for ease of installation and

neat appearance.

The toilet is available with either a compact china bowl to fit

restrictive areas or a large bowl with household size seat

assembly for maximum comfort. Its forward angled double

action pump with convenient top mounted dry bowl selector

is easy and natural to operate. It is self-priming with a dry

suction lift of up to 3 feet (1 meter) and a discharge head to

9 feet (3 meters). A full-flow triadic joker valve resists

blockage while providing positive back-flow prevention.

OPERATION

Manual Marine toilets have traditionally been somewhat

cumbersome and confusing to operate and maintain. The

Jabsco toilet has been designed with user convenience in

mind. The pump assembly is angled forward to provide a

natural, smooth stroke action. It has a top mounted wet/dry

bowl selector which can be operated with the same hand

used for pumping without releasing the pump handle.

The Jabsco toilet is surprisingly easy to operate. Simply

move the wet/dry bowl selector to the wet bowl position

(left) and pump handle up and down a few times to add

some water to the bowl prior to use. After using, flush by

again pumping handle up and down (in wet bowl position)

until bowl is thoroughly rinsed and evacuated. Then move

the wet/dry bowl selector to the dry bowl position (right)

and continue pumping until only about one cup of water

remains in the bottom of bowl. Leave the wet/dry bowl

selector in the dry bowl position when toilet is not in use.

Flood hazard. If toilet is installed below the

waterline or may be below the waterline at any

angle of heel or trim, it must be installed with

properly positioned vented loops. Failure to do

so can result in ﬂooding which can cause loss

of property and life.

WARNING

Positioning and Mounting

The Jabsco Manual Toilet is assembled at the factory for

operation with the right hand. If preferred, or required by

available space, the pump and bowl may be rotated 180

degrees to provide left hand operation. To do this, remove

hose from inlet elbow (back of bowl) and rotate elbow 180

degrees. It may be necessary to remove the elbow, loosen

spud retaining nut and rotate the spud fitting so elbow will

be tight when pointing in the opposite direction. Remove,

rotate 180 degrees and reinstall both the bowl and pump

assembly. Reconnect hose to inlet elbow and the toilet is

ready for left hand operation.

The toilet must be installed on a well supported flat surface.

Ideally, if underside of mounting surface is accessible, the

toilet base should be through-bolted (using 5/16" bolts,

washers and locknuts) to the mounting surface. If the

underside of mounting surface is not accessible, the use of

5/16" lag bolts and washers is an acceptable alternative.

Before installing, position toilet in location to be installed.

Ensure there is adequate space around toilet to easily

operate pump and raise seat and lid to a fully opened

position. Seat and lid should swing open at least 110

degrees and be supported when open to avoid strain on

hinges. Ensure the base drain plug is accessible and inlet

and discharge hoses can be attached to their respective

ports without inducing significant lateral force. The

discharge elbow may be rotated (by loosening two flange

screws, rotating elbow and retightening screws) to accept

the most convenient routing of the discharge hose.

When proper installation has been established mark the

four base mounting holes on mounting surface and remove

toilet. Ensure that no wiring or plumbing is positioned under

the mounting surface which may be accidentally damaged

when the surface is drilled. Drill appropriate size holes for

fasteners being used. Mount toilet using flat washers

between head of bolts and plastic toilet base. If desired a

small bead of silicone or latex sealant may be applied

around base where it contacts the mounting surface to

prevent moisture from getting under the toilet base.

NOTICE: Do not use Polysulfide base sealants because

they may chemically attack the plastic which can result in

breakage.

Plumbing

Do not plumb the toilet to vessel’s

potable water supply. To do so can cause

water contamination that can cause illness or death.

If installing a new inlet thru-hull/seacock, ensure that it is

positioned on a part of the hull which is wetted at all

angles of heel or trim and free of water turbulence at any

hull speed. If discharging waste overboard (check legal

restrictions for overboard discharge), ensure discharge

thru-hull/seacock is both aft of and higher than the inlet

thru-hull/seacock. All inlet plumbing should be a

minimum of 3/4" ID and discharge plumbing a minimum

of 1-1/2" ID. All hose ends should be double clamped

with stainless steel hose clamps. If the toilet is above

waterline route hoses to seacocks, holding tank or

treatment device via a route as direct as possible.

However, for maximum sealing effect on the discharge

joker valve, it is recommended that the discharge hose is

looped upward about 8" above the discharge elbow

before it descends to its termination point. All bends and

elbows in plumbing should be kept to a minimum. It

should not be necessary to use any sealing compound

when attaching hoses to the inlet or discharge ports.

If the toilet is, or can be, below the waterline, at any normal

(including static) attitude of vessel heel and/or trim, a

3/4" vented loop must be installed in a length of hose

connecting the flushing pump to the rear of the bowl.The

vented loop fitting must be positioned 8" above the

waterline at all angles of heel and trim. To accomplish

this, remove the 3/4" hose supplied with toilet and

replace with a new length of hose long enough to properly

position the vented loop. If the toilet is plumbed for over-

board discharge, a 1-1/2" vented loop must be installed

in the discharge hose.The waste vented loop fitting must

also be positioned 8" above the waterline at all angles of

heel and/or trim and ideally should be located as close

to the toilet as practical. (See WARNING.)

If unfamiliar with proper plumbing requirements for

marine toilets, it is recommended that a qualified marine

plumbing technician is contacted to do the installation.

Flood hazard. If toilet is installed below the

waterline or may be below the waterline at any

angle of heel or trim, it must be installed with

properly positioned vented loops. Failure to do

so can result in ﬂooding which can cause loss

of property and life.

WARNING

!Flood hazard. Close inlet and outlet seacocks

prior to disassembling toilet. Failure to do so

can result in ﬂooding which can cause loss of

property and life.

Toilet below

the waterline

WARNING

Produkt Specifikationer

Mærke:	Jabsco
Kategori:	Toilet
Model:	29120-2000

Har du brug for hjælp?

Hvis du har brug for hjælp til Jabsco 29120-2000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Toilet Jabsco Manualer

Jabsco 37010-1096 Manual

12 August 2024

Jabsco 29120-2000 Manual

25 Juli 2024

Jabsco 29090-2000 Manual

29 November 2022

Toilet Manualer

Nyeste Toilet Manualer

Thetford SK220 Manual

2 Oktober 2025

Thetford SK260 Manual

2 Oktober 2025

Liberty Pumps Ascent II-RSW Manual

16 September 2025

Liberty Pumps Ascent II Manual

16 September 2025

PolyJohn PJN3-1007 Manual

27 August 2025

PolyJohn PJN3-1122 Manual

27 August 2025

PolyJohn PJG3-1013 Manual

26 August 2025

PolyJohn PJG3-1004 Manual

26 August 2025

PolyJohn PL01-1000 Manual

26 August 2025

PolyJohn PJN3-1008 Manual

25 August 2025