JANDY iQPUMP01 Manual

JANDY Pomp iQPUMP01

Læs gratis den danske manual til JANDY iQPUMP01 (6 sider) i kategorien Pomp. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 17 anmeldelser. Har du et spørgsmål om JANDY iQPUMP01, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
iQPUMP01
Pump Interface
Quick Start Guide
Control Panel
Auto
Quick Clean
OFF
SVC
Timed Stop
Timed Run
LAN
WANWi-Fi to Phone
iQPUMP01 Interface
This Quick Start Guide is to help you quickly install your
system. Be sure to read all WARNINGS before installation
WARNING
To prevent risk of electrical shock which can result in severe injury or death, ENSURE that the
iQPUMP01 and Pump are OFF and power to the pump is disconnected before proceeding with
installation.
WARNING
To reduce the risk of electric shock, fire or injury, service should only be attempted by a qualified pool
service professional.
This button controls the operational mode of the pump. Push
the button to toggle between Auto and Quick Clean mode. Auto
operates the pump with the settings designated by the app. Quick
Clean will override normal operation and run the pump for 30*
minutes at 3,450* RPM.
This button is used to activate or manually end a direct Wi-Fi to
Phone connection. When ON, you can connect your smart device
directly to the iQPUMP01. When OFF, the iQPUMP01 will attempt to
connect to the pool owner’s router / internet connection.
* Factory default settings - these settings can be changed in the app.
This button controls the Service Modes for the pump. Timed Stop
will keep the pump OFF for 3* hours. Timed Run turns the pump
ON to run for 3* hours at 2,750* RPM.
Helpful Hints
Invite Codes are used to allow access for other users to control the
iQPUMP01 from their own iAquaLink app
Global Pump Settings: min & max speeds, freeze protect, and other
modes such as Quick Clean, Timed Run, and Timed Stop, are only available
when directly connected to the iQPUMP01 via a connection.Wi-Fi to Phone
Master Users are, in most cases, the pool owner. A Master User can
send invitations to other iAquaLink app users to allow them to control
the pump. To claim Master User of the pump, you must be connected to
the iQPUMP01 via a Wi-Fi to Phone connection. To create or send invite
codes, the master user and the iQPUMP01 must both be connected to the
internet. After claiming “Master User”, end the “Wi-Fi to Phone” session
by pressing the button to turn the “Wi-Fi to Phone” LED off. Also ensure
the WEB (or WAN) LED is on before creating or sending an invite code.
Wi-Fi to Phone is technology inside the iQPUMP that transmits a wireless
signal directly to a Wi-Fi enabled device without using an internet
connection. The signal is activated when the Wi-Fi to phone button is
pushed. It will time out after 15 minutes of inactivity or it can also be
manualy deactivated by pushing the Wi-Fi to Phone button while it is on.
WARNING
FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and
qualifi ed in pool equipment by the jurisdiction in which the product will be installed where such state or
local requirements exist, the maintainer must be a professional with suffi cient experience in pool equipment
installation and maintenance so that all of the instructions in this manual can be followed exactly. Before
installing this product, read and follow all warning notices and instructions that accompany this product.
Failure to follow warning notices and instructions may result in property damage, personal injury, or death.
Improper installation and/or operation will void the warranty. Improper installation and/or operation can create
unwanted electrical hazard which can cause serious injury, property damage, or death. Turn off all circuit
breakers required in order to prevent the possibility of electric shock.
www.ZodiacPoolSystems.com
USA: 1-800-822-7933 | CANADA: 1-888-647-4004 | AUSTRALIA: 1800-688-552
Inviting Other Users
The iQPUMP01 allows user to be the “Master User.” The Master User can send one
invitations to other iAquaLink™ users, granting other iAquaLink account holders to
control your pump. In general, only the pool owner should be the Master User.
5.1 In the settings menu, the Master User (only) has the ability to ‘Create Invite
Code’.
NOTE: If the “Create Invite Code” button is not in the settings menu, then you are
not recognized as the ‘Master User’. To become the Master User, connect
directly to the iQPUMP01, then proceed to the settings menu, click the
Claim Master User button, and follow the on-screen directions to become
the Master User.
5.2 Write down the code displayed or click on the code to copy the code to the
clipboard of your device.
5.3 Paste the invite code into an email or text message to the individuals that
you would like to have access to the pump.
5.4 In order for invitees to utilize the code, they will fi rst need to download the
iAquaLink app. After logging in or creating a new account, use the invite
code to add the device by pressing the + or ( ) from the “My Systems”
screen.
5
ZODIAC ® is a registered trademark of Zodiac International, S.A.S.U., used under license.
All trademarks referenced herein are the property of their respective owners.
©2015 Zodiac Pool Systems, Inc. H0509400 Rev E
Zodiac Pool Systems, Inc.
2620 Commerce Way, Vista, CA 92081
1.800.822.7933 | www.ZodiacPoolSystems.com
Zodiac Pool Systems Canada, Inc.
2115 South Service Road West, Unit 3 Oakville (ON) L6L 5W2
+ 1 (888) 647-4004 | www.ZodiacPoolSystems.ca
Before Installation
1.1 Before heading to the job site, install the latest version of the iAquaLink™ app
from the Apple® App Store® or from Google Play®. The app is required to
install the iQPUMP01. Internet access will be needed if you want to connect
the iQPUMP01 to the internet, however it is not required to operate the pump.
1.2 Using the newest version of the iAqualink app installed on your mobile device,
log in to your account, or create a new account following the
on-screen instructions.
Wiring the iQPUMP01 Interface
Mount the iQPUMP01 Interface, using the two (2) screws provided, as high as
possible, and a minimum of 10ft. (3m) from any electric motor. Always mount the
device with the antenna on the right side, pointing up towards the sky.
2.1 Remove power from the pump by turning OFF any breaker which may supply
power to the pump.
2.2 Remove the motor drive service cover.
2.3 Feed the cable from the iQPUMP01 through the RS485 cable fi tting on the
pump and connect to the red RS485 connector by attaching the wires as
follows: 1-red, 2-black, 3-yellow, and 4-green.
2.4 Tighten the RS485 Cable Fitting to secure the cable. Make sure that no other
RS485 connections exist. The iQPUMP01 must be the only connected device.
2.5 Slide DIP switches 1 and 2 UP, so they are in the ON position and slide
switches 3 and 4 DOWN, so they are in the OFF position. If you have a
5-position switch, the 5th switch should be in the ON position.
2.6
Plug the RS-485 connector into the pump and reattach the motor drive service
cover.
2.7 Restore power to the pump.
Connecting the iQPUMP01 to the Internet
Connecting the pump to the internet is highly recommended, but not required
to install the iQPUMP01, or ensure daily scheduled operation. Connecting the
iQPUMP01 to the Internet allows anytime, anywhere remote control of the pump.
4.1 If you want to be able to control the pump through the Internet,
click the “Add to My Systems” button.
4.2 From the Pump Management screen, touch Settings ( for
Android users). From the settings screen select the “Wi-Fi
Settings” button. Select the pool owner’s Wi-Fi network and
enter the network password.
4.3 Push the “Wi-Fi to Phone” button on the iQPUMP01. Ensure the
“Wi-Fi to Phone” LED turns off.
4.4 After a few seconds the orange LAN LED will illuminate
indicating connection to the router. Moments later, the green
WAN (or WEB) LED light will illuminate, indicating connection
to the Internet and the iAquaLink server.
4.5 Now that the iQPUMP01 is connected to the Internet, you can
reconnect to the pump through the Web. From the menu, go
to My Devices, then select the pump named VSPUMP-_ _ _.
Rename the pump from the settings screen. This step can only
be done when connected through the Web. You are now ready
to create invites for other users to have basic acess to control
the pump.
NOTE: You can only create invites when you are the master
user. See step 3.7 and section 5 to claim master user.
iQPUMP01 Setup Using Wi-Fi to Phone
After restoring power to the pump, the Auto LED on the iQPUMP01 should turn on.
3.1 Log in to your iAqualink app on your smart device.
3.2 From the iAquaLink app menu, select “My Systems”, then
“Connect Using Wi-Fi to Phone”.
3.3 Push the “Wi-Fi to Phone” button on the iQPUMP01. Confi rm
that the “Wi-Fi to Phone” LED is illuminated on the iQPUMP01.
3.4 Go to Wi-Fi settings on your mobile device and select the
Wi-Fi network named “VSPump -_ _ _”. The last 3 digits of
the network name will be the same as the last 3 digits of the
iQPUMP01 device number (found on the white label on the side
of the iQPUMP01)
3.5 Return to the iAquaLink app. The app will say “Searching...”
and in a few moments will switch to the Pump Management
screen.
1
2
4
3
4-Position
DIP Switch 5
D
Power Wiring
Ports
Motor Drive
Service Cover
2 - BLACK
3 - YELLOW
1 - RED
4 - GREEN
RS485
Cable (22 AWG)
WARNING
To prevent risk of electrical shock which can result in severe injury or death, ENSURE that the
iQPUMP01 and Pump are OFF and power to the pump is disconnected before proceeding with
installation.
WARNING
Installing the iQPUMP01 requires internal access to the pump drive containing high voltage wiring.
To
reduce the risk of electric shock, fire or injury,
only licensed electricians, or a qualified pool professional
should attempt this installation.
WARNING
To reduce the risk of electric shock, fire or injury,
the pump must be plumbed in and bonded. All high
voltage wiring must be completed before installing the iQPUMP01.
3.6 From the Pump Management screen, you can stop the pump,
begin a custom speed cycle, or return the pump to “Auto”
mode. If these options are not available, the iQPUMP01 may be
in a service mode. A service mode can be ended by pushing the
physical Auto / Quick Clean button on the iQPUMP01.
3.7 From the Pump Management Screen, touch “Settings” ( for
Android users) button to set up the time zone, edit schedules,
min & max speeds, freeze protect, and all other modes such as
Quick Clean, Timed Run, Timed Stop, etc. Push “Claim Master
User” to become the Master User of the pump. As the Master
User, you can create invite codes to allow others to control the
pump.

Produkt Specifikationer

Mærke: JANDY
Kategori: Pomp
Model: iQPUMP01

Har du brug for hjælp?

Hvis du har brug for hjælp til JANDY iQPUMP01 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Pomp JANDY Manualer

JANDY

JANDY JCP07-3AT-S Manual

11 Januar 2025
JANDY

JANDY JCP07-3AT-N Manual

21 August 2024
JANDY

JANDY JCP07-1BD-S Manual

20 August 2024
JANDY

JANDY Stealth Manual

20 August 2024
JANDY

JANDY PlusHP Manual

20 August 2024
JANDY

JANDY VSSHP220AUT Manual

20 August 2024
JANDY

JANDY VSFHP270DV2AS Manual

19 August 2024
JANDY

JANDY JCP15-3AT-N Manual

19 August 2024
JANDY

JANDY WaterFall Manual

18 August 2024
JANDY

JANDY VS FloPro Manual

18 August 2024

Pomp Manualer

Nyeste Pomp Manualer

T.I.P.

T.I.P. Clean Jet 800 Plus Manual

12 Januar 2025
Güde

Güde INOX 100/24 Manual

11 Januar 2025
Vivaria

Vivaria Vario N-3000 Manual

11 Januar 2025
MSW

MSW -FM-N-53 Manual

4 Januar 2025
MSW

MSW -OP-56-DC Manual

4 Januar 2025
MSW

MSW -PUMP CLEAN 100 Manual

4 Januar 2025
Simpson

Simpson SCP71008 Manual

2 Januar 2025
Testo

Testo 565i Manual

1 Januar 2025
Sauermann

Sauermann Delta Manual

1 Januar 2025
Sauermann

Sauermann Omega Manual

1 Januar 2025