Jensen Elite-202 Manual

Jensen Hi-Fi system Elite-202

Læs gratis den danske manual til Jensen Elite-202 (6 sider) i kategorien Hi-Fi system. Denne vejledning er vurderet som hjælpsom af 73 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 37 anmeldelser. Har du et spørgsmål om Jensen Elite-202, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Check for damage: We know you will be eager to install your new Speakers, however, please rstly inspect

your units for any damage. If you nd a problem please contact us immediately at info@bdimports.com.au

Elite-101

Elite-202

Elite- 303

Break in Period:

Premium grade parts and materials are used in these Elite-101/202/303 products so maximum performance can be obtained in

damp and dusty environments such as wall and ceiling cavity. aer which me Bass Break In period is appx 10-20 playing hours

will improve. There is no need to limit playback volume at all during this me.

Wall cut tool

Supplied

Template

Not supplied

Philips screw driver

Stud Finder

Wall Cavity

Depth required:

Elite-101 85mm

Elite-202 62mm

Elite-303 75mm

Elite- 606

See separate manual

Glass

The -Wall / In-Ceiling Speakers Ulmate In

Step 1: Advanced Planning

Decide the placement for your speakers. Advance planning in regards to the placement of your

speakers is crical. It is imperave that the wall or ceiling cavity be free from debris, moisture,

insulaon, and any materials that are easily combusble. The mounng locaon must also be void of wall studs

or bracing in the locaon for the cutout. Adequate Wall Cavity depth (see above to allow speakers to t ush to )

the wall or ceiling surface is important. If you are unsure of the contents of the wall in which you wish to mount

the speakers, Electronic Stud Finders work very well (see FIG 1), otherwise professional installer can assist here. a

Stud Finder

FIG 1.

Congratulaons for buying the best on the planet ! In-Wall Speakers

Please read this manual carefully understanding that advanced planning is essenal.

FIG 2.

Step 4 Cung the Wall / Ceiling :

Using the appropriate wall-cung tool, blade or Stanley knife, accurately cut the hole in the wall material,

based on the correct cut-out dimension (see FIG 3) .

Step 5: Installing Speaker Leads

For Elite-101 and 202, from your Receiver run one speaker cable thru the wall/ceiling to each Le and Right speaker (see FIG 4). For

Elite- TWO303, run speaker cables thru the wall/ceiling to each Elite-303 as this model has inbuilt Centre/Le and Centre/Right

speakers as well as Le and Right. (See FIG 5 and FIG 7). In both cases, leave enough slack in wire so that it can hang out of hole.

Step 3: Template:

Use the supplied template and mark the cut-out on the wall or ceiling. To mark, simply trace with a pencil,

along perforated line (see FIG 2 Ensure your markings are level.).

Step 2: Fing Glass Grills

Fit Elite-101 grills squarely and certain 4 magnets grab and not just 2 or 3 align all 8 pins then gently press be ALL . For Elite-202/303,

Glass panel into rubber bushes. When removing, pull a lile from top, then from boom to remove evenly.

Step 7: Mounng Speakers Insert the enre speaker into the hole. Move Speaker wire away

from back of cone to avoid a possible rale. Using a Phillips head screwdriver, ghten the screws aached to

the dog clamps unl you feel Dog Clamps take grip (9~10 FULL TURNS). At this point you can see the gap

between Speaker Frame and wall/ceiling close fully. Then, See FIG 6. NIP THESE UP - DO NOT OVERTIGHTEN.

Note: If you are unable to install these speakers yourself, please contact an authorized electrician or

installaon contractor.

Matching Subwoofer : Elite- 606:

140 Was RMS, Heavy-Duty driver with 40oz magnet is perfectly matched “monster” and 2”Voice Coil

to ALL Speakers. Available in stunning -Gloss White or Black. See separate Info Manual. JENSEN Hi

Step 6: Red- -Red & Black to Black to

Connect the speaker wire from the posive (RED+) terminal on the receiver to the posive (RED+) terminal on the speaker. Connect

the negave (BLACK-) the same way to the negaves. Note: If you inadvertently reverse one of the connecons (i.e. RED to BLACK)

you will noce a severe lack of Bass from your system. This is called wiring your system “Out of Phase”. If this occurs, check the wiring

and reconnect as necessary.

Sound Sengs

Boost switch. Adjust Elite 202 / 303 Treble switches to suit your sound preference -.

If using a Subwoofer set to (+) to fully maximize performance. Note: Elite-101 has no switches but is

factory preset to Max Boost (+).

Eyeball Tweeters. You can adjust the angle of the Tweeter slightly in order to compensate for poor

mounng locaons. Do this by adjusng Tweeter casing. in any way as DO NOT touch the Tweeter

permanent damage may occur.

FIG 3.

Elite-101, 202 & 303

Once nal mounng posions are

determined, pencil and use

template (supplied) to mark the

wall and cut-out.

Template

Boost switches.

Eyeball Tweeters

Elite

606

Elite-101

Elite-202

Elite-303

JENSEN

Produkt Specifikationer

Mærke:	Jensen
Kategori:	Hi-Fi system
Model:	Elite-202

Har du brug for hjælp?

Hvis du har brug for hjælp til Jensen Elite-202 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hi-Fi system Jensen Manualer

Jensen Elite-202 Manual

1 April 2024

Jensen MS30 Manual

29 December 2023

Jensen Power 760 Manual

6 December 2023

Jensen Power 900 Manual

10 Oktober 2023

Jensen Elite-303 Manual

11 November 2022

Jensen JMS2212 Manual

24 Oktober 2022

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

Pro-Ject Head Box E Manual

30 Juli 2025

Pro-Ject Uni Box S3 Manual

30 Juli 2025

Hamilton Buhl PA-25 Manual

30 Juli 2025

SSL SQ4 Manual

29 Juli 2025

SSL ML46DB Manual

29 Juli 2025

SSL ML39USA Manual

29 Juli 2025

SSL Evolution EV2.200 Manual

29 Juli 2025

SSL Evolution EV4.400 Manual

29 Juli 2025

Panasonic SH-ALL1CP Manual

29 Juli 2025

SSL ML42B Manual

29 Juli 2025