Jensen VX7071 Manual

Jensen Navigator VX7071

Læs gratis den danske manual til Jensen VX7071 (4 sider) i kategorien Navigator. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Jensen VX7071, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

What s in the Box’

The following items are supplied

with the VX702 :1

• VX702 Head Unit1

• Trim Ring

• Hardware

• Power/Speaker Output Harness

• Remote Control

• External Microphone

• GPS Antenna

• Installation Guide

Tools and Supplies

The following tools and supplies

are needed to install the head unit:

• Torx type,  at-head and Philips

screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screw

driver, socket wrench set or other

tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

VX7021

Installation / Quick Start Guide

Complete operation manuals are

online at www.jensenmobile.com

Note: There is no operation manual in this package

Disconnect the Battery

• To prevent a short circuit, be sure t the ignition and remove the negative (-) battery cable prior to installation. o turn off

NOTE: If

the is to installed in a car head unit be equipped with an on-board drive or navigation computer, do not disconnect the

battery cable conditions, cable. If the is disconnected, computer memory may be lost. Under these the use extra

caution during installation to avoid causing a short circuit.

Replacing the Fuse

• When replacing the vehicles adio fuse always use the proper rated replacement fuse. Using a fuse with an improper ratingr

could damage the unit and cause a fi re.

ISO-DIN Installation

The is designed to t into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may head unit fi

be used with the original factory mounting brackets of some oyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to T

mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of

installation.

NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal

laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.

Using the Cosmetic Trim Ring

A cosmetic trim ring is supplied with the head unit for installation

 exibility. This unit will  t into most import dashes with little or no

modi cation to the dash board/cavity. Some US domestic vehicle

dashes will accept a Double-DIN chassis, but there is usually a

small gap between the radio and dash piece after installation is

complete. In this case, use the trim ring to conceal any gaps that

may be present.

1. Remove the existing factory radio from the dashboard or

center console mounting. Save all hardware and brackets as

they will be used to mount the new radio.

2. Remove the factory mounting brackets and hardware from the

existing radio and attach them to the new radio.

CAUTION! Do not exceed M5 X 6MM screw size. Longer

screws may damage components inside the chassis.

3. Place the radio in front of the dashboard opening so the wiring

can be brought through the . Follow thedash opening

wiring diagram carefully and make certain all connections are

secure and insulated with wire nuts or electrical tape. After

completing the wiring connections, plug the connector into

the mating socket on the rear of the chassis Turn the. unit

ON to confi rm operation (vehicle ignition switch must be

“ON”). If the unit does not operate, re-check all wiring until the

problem is corrected.

4. Mount the new radio assembly to the dashboard or center

console using the reverse procedure in step 1 above.

CAUTION! Be careful not to damage the car wiring.

NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the

unit is mounted within this limitation.

The recommended Interface SWC is the PAC control adapter SWI-RC steering wheel .

SWI-RC installation hints:

1. Set "Radio Select Switch" et the SWI-RC to position 7 Pioneer/Sony/Other .. S - " "

2. " "Programming - Use the Other radio function mapping order for Jensen branded head units.

3. When programming the SWI-RC, if a function is not supported (or not desired), then the function be skipped as perMUST

the PAC SWI-RC instructions.

4. The SWC functions also be programmed in the correct order per the PAC SWI-RC radio function mapping orderMUST

instructions.

S W C Readyteering heel ontrol (SWC)

Produkt Specifikationer

Mærke:	Jensen
Kategori:	Navigator
Model:	VX7071

Har du brug for hjælp?

Hvis du har brug for hjælp til Jensen VX7071 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Navigator Jensen Manualer

13 August 2024

7 August 2024

27 Juli 2024

27 Juli 2024

20 Juli 2024

18 Juli 2024

13 Maj 2024

24 September 2023

18 August 2023

13 Juli 2023

Navigator Manualer

Nyeste Navigator Manualer

Rand McNally OverDryve Manual

22 September 2025

Rand McNally TND 750 Manual

21 September 2025

Rand McNally RoadExplorer 70 Manual

21 September 2025

Rand McNally TND 740 Manual

20 September 2025

Rand McNally OverDryve 7 Manual

20 September 2025

Rand McNally RoadExplorer 80 Manual

20 September 2025

Rand McNally Foris Manual

20 September 2025

Rand McNally RoadExplorer 5 Manual

20 September 2025

Rand McNally IntelliRoute TND 700 Manual

20 September 2025

Rand McNally RVND 5525 LM Manual

20 September 2025