Jonard Tools HDMI-100 Manual

Jonard Tools Ikke kategoriseret HDMI-100

Læs gratis den danske manual til Jonard Tools HDMI-100 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Jonard Tools HDMI-100, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
HDMI Cable Tester (HDMI-100) - User Manual
IMPORTANT SAFEGUARDS:
• Read everything in this manual before using your HDMI-100 Cable Tester.
• When the low voltage indication appears, the 9V battery will need to be replaced. (Note: Power input to this device cannot
exceed 12VDC).
• If you do not use this tester for a long period of time, remove the battery to prevent potential leakage.
• Meets the European Union CE standards: EN61326-1:2013; EN61326-2-2:2013.
I. Function Overview:
The HDMI-100 is a professional piece of test equipment for testing 1.2V/ 1.3V/1.4V/2.0V HDMI cables. It can quickly scan and
test up to 19 wires and inform you if any connections are short circuits, open circuits, or are in the wrong order.
1. Test modes: a) Fast scan mode b) Full display mode.
2. HDMI and Mini HDMI cable can be used with this device. See below for the congurations:
a. Both ends are standard HDMI connectors (Type A- Type A)
b. Both ends are HDMI Mini connectors (Type C - Type C)
c. One end is HDMI, other end is HDMI Mini connector (Type A- Type C)
3. Low Battery Indicator: When the battery voltage is lower than 7.2V, the blue light ashes, prompting you to replace the battery.
4. Auto Shut Down: After 10 minutes without being used, the device will automatically shut down.
II. How To Use:
1. Install the 9V battery by opening the battery compartment using a small Philips head screwdriver.
2. Press the On/Off/Mode button for 0.5 seconds to power on the unit. The Power LED should illuminate a solid blue, and the
Status LED should be blinking red.
3. Insert one end of the HDMI or Mini HDMI cable into the Transmitter and the other end into the Receiver.
4. Short press the On/Off/Mode button to switch between scan and full display modes. The Status LED will be solid red for full
display mode.
a. Scan mode should be used for specic defect detection.
b. Full display mode should be used for quick alignment detection.
5. Hold the On/Off/Mode button for 2 seconds to power off the unit. It will also automatically turn off after 10 minutes.
III. How To Evaluate Results:
1. If the cable is error free:
a. Scan Mode: Each LED will synchronize one by one from 1 to 19.
b. Full Display Mode: The LED indicators of the transmitter and receiver will all illuminate.
2. If a short circuit is detected: The corresponding indicator of the transmitter will illuminate, and the corresponding indicator of
the Receiver will not illuminate.
3. If an open circuit is detected: Both the corresponding indicator of the transmitter and receiver will not illuminate.
4. If two or more lines are crossing, in wrong sequence or order: Both corresponding indicators of the transmitter and receiver
will illuminate, but they will not be synchronized.
5. The Shield LED indicates if the cable being tested has shielding or not. If the Shielded LED illuminates, the cable being tested
is shielded. If it’s ickering, the shielding may be damaged. If the LED does not illuminate, the cable does not have shielding.
IV. Maintenance and Cleaning
1. Clean the HDMI-100 as needed using a soft dry cloth.
2. Do not use cleaning agents or chemicals to clean the surface and avoid moisture when possible.
Tel 914.793.0700 | Fax 914.793.4527 | jonard.com
1. Transmitter HDMI Mini (Type C) Interface
2. Transmitter HDMI Standard (Type A) Interface
3. Transmitter Power Indicator
4. Transmitter On/Off/Mode Button
5. Transmitter Analog Status Indicator
6. Transmitter Alignment Indicator
7. Receiver HDMI Standard (Type A) Interface
8. Receiver Alignment Indicator
9. Receiver HDMI Mini (Type C) Interface
1
2
3
4
5
6
7
8
9

Produkt Specifikationer

Mærke: Jonard Tools
Kategori: Ikke kategoriseret
Model: HDMI-100

Har du brug for hjælp?

Hvis du har brug for hjælp til Jonard Tools HDMI-100 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Jonard Tools Manualer

Jonard Tools

Jonard Tools FLS-55 Manual

28 December 2024
Jonard Tools

Jonard Tools FPM-50A Manual

28 December 2024
Jonard Tools

Jonard Tools FCC-120 Manual

28 December 2024
Jonard Tools

Jonard Tools RJ11 Manual

2 December 2024
Jonard Tools

Jonard Tools FOR-3000 Manual

2 December 2024
Jonard Tools

Jonard Tools HDMI-100 Manual

18 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IOptron

IOptron iEFW-18 Manual

15 December 2025
Magliner

Magliner CooLift CTA48 Manual

15 December 2025
Epson

Epson GP-M831 Manual

15 December 2025
Prince Castle

Prince Castle EHB42F1-GMS02 Manual

15 December 2025
SkyRC

SkyRC TX58025 Manual

15 December 2025
La Crosse Technology

La Crosse Technology LTV-THP1-C1 Manual

15 December 2025
Growatt

Growatt MIN2.5-6KTL-XH2 Manual

15 December 2025
Bosch

Bosch SBH6YCX02F Manual

15 December 2025
Eurosound

Eurosound HDBT-BYOD-EX1-P Manual

15 December 2025
Milwaukee

Milwaukee MX Fuel MXF002 Manual

15 December 2025