JUNG FDBIS50 Manual

JUNG Fingeraftrykslæser FDBIS50

Læs gratis den danske manual til JUNG FDBIS50 (11 sider) i kategorien Fingeraftrykslæser. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 2 anmeldelser. Har du et spørgsmål om JUNG FDBIS50, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/11

Fingerprint system

Ref.-no.: ..BIS 50..

Operating instructions

Fingerprint system

1. Safety Instructions ............................................................................ 1

2. Device layout ..................................................................................... 2

3. Function ............................................................................................. 2

4. Operation............................................................................................ 2

4.1. Storing a master nger ................................................................. 4

4.2. Storing user fingers....................................................................... 5

4.3. Deleting the user finger................................................................. 7

4.4. Deleting all fingers ........................................................................ 7

4.5. Changing the switching output ON time ....................................... 8

5. Fitting and electrical connection..................................................... 9

5.1. Installing the device ...................................................................... 9

5.2. Start-up ....................................................................................... 10

6. Appendix .......................................................................................... 10

6.1. Technical data............................................................................. 10

6.2. Control functions – overview....................................................... 10

6.3. Accessories................................................................................. 11

6.4. Guarantee ................................................................................... 11

1. Safety Instructions

Electrical equipment must be installed and fitted by qualified

electricians only.

Failure to observe the instructions may cause damage to the device

and result in fire or other hazards.

Only for indoor use.

The device is not protected against tampering. Do not use in areas

critical with regard to safety or in combination with alarm systems.

This device is a safety class III device. Use a safety transformer as

per EN 61558 with an output voltage of 12 VDC as power supply.

For the installation and for the laying of cables observe the relevant

specications and the standards for SELV voltages.

These operating instructions are part of the product and must be

left with the final customer.

Stand: Aug-08 325 642 13

Fingerprint system

Ref.-no.: ..BIS 50..

2. Device layout

Fig. 1

(1) Design cover

(2) Indicator LEDs red, amber, green

(3) Line-oriented sensor

(4) Control button under design cover

3. Function

Designated use

• The device verifies the access authorization of persons by

comparison of their fingerprints. For this verification, the person

demanding access runs a nger over the sensor surface. If the

access authorization is confrmed, the device enables a switching

output for a preset time, e.g. to activate the opener of doors inside a

building.

• Installation in a ush-mounting box as per DIN 49073.

Recommendation: Use the deep mounting box.

Device features

• Storing capability for up to 50 user fingers

• 3 master fingers for administration purposes

• Switching output ON time adjustable between 0.5 and 10 seconds

• 3 coloured LEDs as indicators

• Stored finger data remain stored even after mains failures

• Separate power supply (accessory part) for device required

L The device uses a heated sensor. A slight temperature increase can

be felt when the finger is placed on the sensor. This temperature

increase is of no risk to the user.

The necessary operating temperature is reached 30 seconds max.

after switching on.

4. Operation

Running the finger correctly over the sensor surface

The sensor in the device works like a line scanner. When a finger is run

over the sensor surface, the device builds an image of the ngerprint

(Fig. 2) and stores it.

Produkt Specifikationer

Mærke:	JUNG
Kategori:	Fingeraftrykslæser
Model:	FDBIS50

Har du brug for hjælp?

Hvis du har brug for hjælp til JUNG FDBIS50 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fingeraftrykslæser JUNG Manualer

JUNG FDESBIS50 Manual

7 August 2025

JUNG FDALBIS50 Manual

7 August 2025

JUNG FDBIS50 Manual

6 August 2025

Fingeraftrykslæser Manualer

Nyeste Fingeraftrykslæser Manualer

Vimar ELVOX 41016 Manual

17 November 2024

Media-Tech MT5107 Manual

27 August 2024

Perfect Choice PC-181026 Manual

17 August 2024

ZKTeco ZK-DACTYSCAN84c Manual

15 August 2024

Suprema BioLite Solo Manual

13 August 2024

Hikvision DS-K1F820-F Manual

10 Juli 2023

Hikvision DS-K1201EF Manual

16 Oktober 2022