JUNG RAD A 518 WW Manual

JUNG Radio RAD A 518 WW

Læs gratis den danske manual til JUNG RAD A 518 WW (2 sider) i kategorien Radio. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om JUNG RAD A 518 WW, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Flush-mounted radio with

display RAD...

Device descripon

The Jung ush-mounted radio RAD… consists

of a display cover and a ush-mounted

power supply unit.

The display cover is used for display and

operaon. All the sengs are made using

the sensor buons. The display shows the 8

staon informaon from RDS, the me and

the current sengs.

The radio power supply unit contains the

connecons for the mains voltage, inputs

and the loudspeaker.

The radio can be operated with one or two

LSM... loudspeaker modules.

The extension input allows the radio to be

switched on or o, e.g. together with the

light.

The radio signal is obtained from the

connecon to the mains voltage. In

situaons where recepon is dicult, the

oponal cord aerial can be used.

Other audio sources can be played back

using an AUX input, e.g. using the music

centre MC..100… .

Safety information

Electrical equipment must only be installed

and assembled by qualied electricians.

Failure to comply with these instrucons

may result in damage to the device, re or

other hazards.

This product is only intended for use in dry

rooms.

These instrucons are a component part of

the product and must remain with the end

customer.

Operaon

The lower half of the cover is used for

operaon. All operaon is carried out using

8 sensor buons.

When idle, the buons and display may be

hidden, depending on the sengs.

They are reacvated when the sensor

buons are touched again.

Switch-on / Switch-o

The radio is switched on and o

here.

If the buon is pressed for 3 seconds when

the system is switched on, then the sleep

mer (fall asleep funcon) can be acvated.

Sengs

Basic conguraon of brightnesses,

alarm me, and much more.

Alarm funcons

The alarm, which has a gradually

increasing volume, is switched on

and o here.

If the buon is pressed for longer than

3 seconds, this opens the menu for seng

the alarm me.

Favourites

Preferred staons can be saved to

the Favourites or the AUX input

selected.

Operang buons

Staon search, volume seng and the

navigaon/

seng in the menu.

Brightness of display during standby

adjusts the brightness for the

standby state.

The lowest level is Night mode.

Night mode

In Night mode, the display is switched o

completely as standby.

Pressing any buon brings the display back

from Night mode.

Main menu

Aer switch-on, the staon informaon and

status line are shown in the display.

The status line provides informaon on the

selected favourites, me and alarm

operaon.

When idle, this informaon is reduced to the

me and date.

Staon selecon

The next staon is selected using the

buons.

RDS (Radio Data System)

During operaon, the display shows the

staon name and, in some cases, addional

informaon, e.g. on the current song.

If this informaon is not available, then

frequency informaon on the selected radio

staon is displayed.

Adjusng the volume

The volume is adjusted using .

Favourites

Briey pressing the buon selects the

saved favourites or the AUX input.

Cancel Select -/+ Conrm

In radio operaon, a long press of the

buon (> 3 s) adds the current staon to the

Favourites list.

Up to 8 favourites are possible.

Sengs

The submenus can be found using the

buon. The menu is operated with the

sensor buons below.

Cancel Select -/+ Conrm

Here you can select one of the following 8

submenus with the +/- buons.

With the buon you get into the

selected submenu to change required

sengs.

AUX input

When the AUX input is acvated, radio

recepon is terminated and playback comes

from the external source. If the input is

deacvated again, radio operaon will

recommence.

Alarm me

The set alarm me starts the radio with an

increasing volume.

The display and buons are previously

illuminated at full brightness.

The buons terminate any further

increase in volume.

The buon switches the alarm o.

The buon switches the funcon on and

o.

Sleepmer (Fall asleep funcon)

The Sleepmer (fall asleep funcon)

switches the radio o automacally aer

the selected period of me.

The countdown is displayed in the status

line.

Buon brightness

The brightness and switch-o behaviour of

the buons can be varied.

On switching-o, the informaon in the

display is reduced to the display of staon

name and the me.

If the system is operated again, the buons

become brighter again.

Brightness of operaonal display

The display brightness can be reduced.

Loudspeaker

During operaon, the radio switches

between stereo and mono operaon

automacally. If recepon condions are

variable, it may be wise to select connuous

mono operaon. This allows two dierent

areas to be lled with sound.

Time

Normally, the recepon of an RDS staon is

sucient to perform this seng

automacally. However, the current me

can also be set manually.

Default seng

The state as delivered is restored. In so

doing, the 8 strongest staons are saved

automacally.

Flush-mounted radio with

display RAD...

Operang instrucons

Albrecht Jung GmbH & Co. KG

Volmestrasse 1

58579 Schalksmühle

Germany

www.jung.de

We reserve the right to make technical

changes.

en_RAD_V3.docx

02/2014

0024073100

The symbol is a free trade symbol,

intended solely for the authories and does

not carry any guarantee of properes.

Guarantee

Our products are under guarantee within

the scope of the statutory provisions.

Please send the device, postage paid, to our

central Customer Service Centre, with a

descripon of the error.

ALBRECHT JUNG GMBH & CO. KG

Volmestrasse 1

58579 Schalksmühle

Germany

Telephone: +49 2355 806-0

Fax: +49 2355 806-204

kundencenter@jung.de

www.jung.de

Service Centre

Kupferstr. -17 19

44532 Lünen

Germany

Correct use

• Installaon in a ush-mounted device box

according to DIN EN 49073

(Recommendaon: Deep sockets)

• VHF recepon in the frequency range

87.5 MHz to 108 MHz

Product properes

• VHF radio with display and sensor buons

• Real glass front panel

• Stereo recepon

• Connecon terminals for two loudspeakers

• Stereo/mono switch-over

• Simple operaon

• Integrated VHF aerial

• High level of recepon quality

• Automac and manual staon search

• Storage of 8 favourites

• Switch-on with most recent staon

• Switch-on with most recent volume

• Alarm funcon

• Sleep mode

• Switch-on/switch- f using extension of

• Oponal external cord aerial

Art. no. RAD-ANT available as accessory

Mounng

The radio RAD… is designed for mounng in

ush-mounted DIN EN 49073 sockets.

The ush-mounted power supply unit

contains the connecons for the mains

voltage, loudspeaker and possibly the

extension.

The display cover is aached to the power

supply unit together with the frame.

DANGER!

Touching live parts can result in an

electric shock.

An electric shock can be fatal.

Before working, disconnect all the

appropriate cable protecon

switches. Cover live parts in the

vicinity.

Mains connecon

The radio requires a permanent mains

power connecon.

It is not allowed to use the terminals to loop

through wires.

Connecng the extension

The extension connecon is used to switch

the radio o and on using switches,

e.g. together with the light.

The extension input may only be operated

with the same phase as the radio.

Connecng an external cord aerial

The rear-side connecon for the external

aerial may only be used to connect the cord

aerial, art. no. RAD-ANT. Connecon to roof

aerials of shared aerial systems is not

permied.

To connect the cord aerial, remove the

jumper. Make sure to store the jumper for

later use of the radio without cord aerial.

Insert the aerial in the lower connecon.

Using the AUX input

The AUX input is used to connect external

sources, e.g. the music centre MC..100… .

Within the device box, all the cables carrying

low voltages (including the oponal cord

aerial) must have an insulang hose, in

order to guarantee secure isolaon.

The AUX input is selected using the

Favourites buon or in the menu.

Connecng a loudspeaker

The radio is designed for operaon with one

or two LSM... loudspeaker modules. The

connecon cable can be up to 5 m long.

Within the device box, all the cables carrying

low voltages must have an insulang hose,

in order to guarantee secure isolaon.

In normal stereo operaon, both outputs

(L+R) are used. If necessary, the receiver

switches to mono operaon automacally.

In the case of manual switch-over to mono

operaon (2 x mono), the radio can also be

used with just one loudspeaker.

The connecon of mulple loudspeakers to

each output is not permied.

Third-party loudspeakers may only be used

if their technical data is idencal to the Jung

LSM... .

Please observe the polarity.

Mounng of the power supply unit

Aer connecon of all the cables, mount the

power supply unit in the device box in the

right posion.

Mounng of the display unit

Aer the power supply unit has been

mounted in the device box, aach the

display cover, including the frame, to the

power supply unit in the right posion.

First commissioning

Switch the device on using the buon.

During rst commissioning, the 8 strongest

staons are saved automacally.

If necessary, adjust the sengs for the

loudspeakers and brightnesses.

Normally the brief recepon of an RDS

staon is sucient to set the me and date

automacally. Otherwise, the me can also

be set manually.

Technical data

Radio RAD…

Rated voltage: AC 230 V ~

Frequency: 50/60 Hz

Ambient temperature: 0 …+ 50 °C

Humidity: 15 % … 90 %

No dew formaon

Frequency range: 87.50 MHz … 108.00 MHz

Protecon rang: IP 20

Connecon: Screw terminals

1 x 2.5 mm² or 1 x 1.5 mm²

Loudspeaker connecon cable:

Twin-core cable H03VH-H, 2 x 0.75

alternavely:

-(St)- Y 2x2x0.6 mm JY

Length: max: 5 m

Loudspeaker LSM…

Rated power: 2.5 W

Impedance: 4 Ω

Frequency range: 120 ... 15000 Hz (-10 dB)

AUX input:

Impedance: 470 Ω

Input level: 1 V

Produkt Specifikationer

Mærke:	JUNG
Kategori:	Radio
Model:	RAD A 518 WW
Kode for international beskyttelse (IP):	IP20
Tænd-/slukkontakt:	Ja
Vekselstrømsindgangsspænding:	230 - 240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Produktfarve:	Hvid
Indbygget skærm:	Ja
FM radio:	Ja
Indbyggede højttaler(e):	Ja
Relativ luftfugtighed ved drift (H-H):	15 - 90 %
Tuner type:	Digital
Udgangseffekt (RMS):	2.5 W
Ethernet LAN:	Ingen
Driftstemperatur (T-T):	0 - 50 °C
Termometer:	Ingen
Integreret ur:	Ja
Frekvensområde:	120 - 15000 Hz
Impedens:	4 ohm (Ω)
Strømkilde:	Vekselstrøm
Kan monteres på væggen:	Ja
Strømkilde type:	Vekselstrøm
Antal indbyggede højttalere:	1
AUX-indgang:	Ja
Understøttede radiobånd:	FM
RDS Tuner inkluderet:	Ja
MP3-afspilning:	Ingen
Antenne type:	Intern
FM båndbredde:	87.5 - 108 Mhz
Justering af lysstyrke:	Ja
Radiotype:	Ur
Antal forudindstillede stationer:	8
Lydalarmer:	Ja
Automatisk digital indstilling:	Ja