Tubes: steel, powdered, black
Caps, handles, guides: PA, PE
Upholstery cover: Trevira CS (flame retardant)
Load capacity 1 person, 100 kg (static load)
Chair: W × D × H: 500 x 510 x 835 mm
Seat surface: 450 x 450 mmm; height: ~500 mm
Seat inclination: -4°/+2° (infinitely adjustable)
- Professional orchestra chair with upholstered seat and backrest
FEATURES AND CAPABILITIES
- The black, powder-coated base frame is made of robust 18 × 2 mm
- Upholstery and fabric (Trevira CS) are made of flame-retardant
- Extremely hard-wearing upholstery (100,000 abrasion cycles)
- With adjustable seat inclination
- With two sets of parquet protectors (a. glides, b. foot caps)
- Stackable, thus space-saving storage (up to five chairs)
Thank you for choosing this product. Please read and follow these instructions carefully. It
informs you about all important steps necessary for safe installation and operation. We
recommend that you keep them for future reference.
- Before and after using the orchestra chair, please carry out a visual inspec-
- tion and check for completeness, ease of movement, and possible damage.
- A damaged chair may initially not be used any further or only after qualified
- A maximum of five orchestra chairs may be stacked in accordance with the
- specifications for safe stacking (see Chapter 3). Stacking beyond this leads
- to instability and overloading and may therefore pose a hazard.
- Use only on suitable subfloors (i.e. ensure evenness and sufficient load-
- Careful handling maintains the functionality and longevity of the chair and
- ensures the safety of both the chair and user.
1. COMPONENTS, DIMENSIONS
The orchestra chair comes completely pre-assembled. Firstly, please carry out a
visual inspection in order to ensure that all parts are complete and, as far as
recognizable, in good order:
a Seat cushion: integrity, tight fit...
b Backrest upholstery: integrity mobility...
c Mechanics of seat inclination: movement, tight fit…
d Base frame: wobble-free stand, powder coating...
e Plastic glides: presence, alignment...
f Accessory bag (foot caps): completeness (4 pieces)…
(see enclosed instructions for installation)
The angle of inclination of the upholstered seat has an influence on the
user’s well-being and health; this should not be underestimated. This
chair makes it possible to adjust the inclination to personal requirements.
STEPLESS ADJUSTMENT OF INCLINATION
The adjustment mechanism is located underneath the seat.
2.1 Lower the rear seat (max. -2°) →
2.1.1 Turn the handle to the right
2.2 Tilt the seat forwards (max. 4°) →
2.2.1 Turn the handle to the left
3. STACK CHAIRS - up to five chairs
3.1 Before stacking, the rear seat surface of the chairs must be
3.1 completely lowered. To do this, turn the handle to the right as
3.1 far as it will go (see ). 2.1.1
3.2 A maximum of five chairs may be stacked.
3.3 The side rods on the foot tubes must be placed on the plastic
3.3 rings of the cross tubes.
3.4 If chairs are stacked incorrectly (more than five chairs, seat not lowered),
3.4 there is a DANGER OF TIPPING because of the shift in the center of gravity.
FAULT-FINDING (F) and REPAIR (R)
F: Orchestra chair tilts:
F: B: Check subfloor for suitability
F: B: Is the orchestra chair in order? (base frame, glides)
F: Stack of chairs wobbles:
F: B: Lower the seat: - turn the handle to the right as far as it will go
F: B: Observe maximum number of chairs: 5
F: B: Stack the chairs on top of each other again with care
F: B: Check the condition of the chairs
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
13435-000-55 Rev.02 03-80-977-00 11/23
