Kanto YU Passive Manual

Kanto Højttaler YU Passive

Læs gratis den danske manual til Kanto YU Passive (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Kanto YU Passive, eller vil du spørge andre brugere om produktet?

Side 1/4
Supporting your digital lifestyle
English
User Manual
YU Passive Speakers
Thank you for choosing YU Passive speakers, designed by Kanto in Canada. We recommend you
read these instructions carefully before using the speakers, and keep them for future reference.
Kanto cannot be liable for damage or injury caused by incorrect setup or use of this product.
These speakers were carefully tested and inspected during production, and before packaging
and shipping. After unpacking, please check for any damage. It is rare that a unit is damaged
during shipping, but if this happens contact your retailer immediately. You can also call Kanto
directly at 1-888-848-2643 or email support@kantoliving.com.
Introduction
What's in the Box?
YU Passive
Speakers
User
Manual
x8
Self-Adhesive
Rubber Feet
x2
2
We recommend the Kanto SP26PL and SP32PL oor stands for both the YU Passive 4" and YU Passive
5.25". For desktop use, we recommend the S4 and SP9 desktop stands for YU Passive 4", and the S6 and
SP6HD desktop stands for YU Passive 5.25".
The space between the two speakers and the distance from the listener is important. If the speakers are
positioned too close or too far apart, stereo imaging will not be fully developed.
YU Passive is designed to perform optimally positioned at least 8” from the rear wall in an average
listening room. However, it may not be possible to install the speakers in this position and since rooms
vary in shape, size, and furnishing, a certain amount of experimentation is necessary to determine the
most suitable position.
Moving the speakers very close to the rear wall will enhance the bass frequencies but will tend to reduce
soundstage depth, while moving the speakers away from the rear wall will tend to have the opposite
eect. Avoid positioning the speakers close to or in the corners of the room, as this will excite undesirable
room coupling in the low and middle frequencies. If the width of the rear wall is limited then toe-in the
speakers slightly to reduce reections. Room characteristics and positioning have a profound eect on
the performance of the speakers, so time and eort devoted to achieving the optimum positions will be
rewarded.
Setting Up Your Speakers
YU Passive 4" is rated to 70 W at 4 ohms, YU Passive 5.25" is rated to 100 W at 6 ohms.
Repeat the above procedure for connecting the remaining speaker to the RIGHT amplier channel. Make
sure that no bare wires from any of the connections touch other teminals as this could cause a short and
damage your equipment.
Conventional Connection
Amplier Requirements
Using 16-12 gauge speaker wire, connect the RED "positive" (+) terminal of one speaker to the RED
"positive" (+) terminal of your amplier's LEFT channel. Connect the BLACK "negative" (-) terminal of the
speaker to the BLACK "negative" (-) teminal of your amplier's LEFT channel.
Attention
When connecting audio cables the amplier must be turned OFF. After connecting all cables, the unit can be turned . ON
5.25”
YUP 6
100 W
6 Ω
4”
YUP4
70 W
4 Ω


Produkt Specifikationer

Mærke: Kanto
Kategori: Højttaler
Model: YU Passive

Har du brug for hjælp?

Hvis du har brug for hjælp til Kanto YU Passive stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler Kanto Manualer

Kanto

Kanto ORA4 Manual

2 Januar 2025
Kanto

Kanto REN Manual

11 December 2024
Kanto

Kanto ORA Manual

28 August 2024
Kanto

Kanto YU6 Manual

19 August 2024
Kanto

Kanto SYD Manual

18 August 2024
Kanto

Kanto YU Passive Manual

18 August 2024
Kanto

Kanto YU Manual

17 August 2024
Kanto

Kanto YU2 Manual

17 August 2024
Kanto

Kanto TUK Manual

14 August 2024
Kanto

Kanto YU4 Manual

14 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer