Katadyn REPAIR SEAL KIT PowerSurvivor 80E Manual

Katadyn Marine REPAIR SEAL KIT PowerSurvivor 80E

Læs gratis den danske manual til Katadyn REPAIR SEAL KIT PowerSurvivor 80E (9 sider) i kategorien Marine. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Katadyn REPAIR SEAL KIT PowerSurvivor 80E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

INSTALLATION INSTRUCTIONS

REPAIR SEAL KIT

PowerSurvivor 80E

Print No.: 8012825/0 Katadyn North A merica Inc. Katadyn Products Inc.

4830 Azelia Avenue North Pfäffikerstrasse 37

Minneapolis, MN 554429 U.S.A. 8310 Kemptthal  Switzerland

Tel +1 800 755 6701  Fax +1 763 746 3540 Tel +41 44 839 21 11  Fax +41 44 830 21 99

marine@katadyn.com  www.katadyn.us info@katadyn.ch  www.katadyn.ch

PURPOSE OF THE KIT

The Repair Seal Kit should be installed after 1000 hours of operation. It should be installed regardless

of whether or not there is leakage or a reduction of fresh water. Learning to perform this procedure will

ensure optimal performance of your watermaker.

NOTE: If the unit has been operating in water with silt or higher than normal salinity, the Seals will

wear somewhat faster.

Before beginning the Repair Kit procedure, note the following precautions:

1. Keep the work area clean of dirt, hair, and other contaminants.

2. Avoid scratching Pump Components when removing or replacing O-rings.

3. Never use petroleum-based lubricants on Seals and O-rings as a substitute for Silicone

Grease.

4. When installing O-rings do not roll or twist them.

NOTE: Average time to replace all seals is 1 hour. If you are performing this maintenance for the first

time, expect 3 hours.

KIT CONTENTS (See Figs. A-3 and A-4)

TOOLS REQUIRED

 Piston Seal Installation Tool – supplied with kit

 Needle-nosed pliers

 ¼-inch Allen wrench

 ½-inch open-end wrench

 11/16-inch open-end wrench

 7/8-inch open-end wrench

 ½-inch deep socket and socket wrench

 small flat-blade screwdriver

 small scissors

Disassembly:

1. Before beginning disassembly, run the watermaker and stop it when the piston shaft is at its

farthest point of travel away from the pump (toward the drive assembly). This provides enough

room for sliding the rubber boot

back toward the pump in Step 3.

2. Use the 11/16" open-end wrench

to disconnect the two high-

pressure hoses (coming from the

membrane housing) from the tube

connectors on the check valve

plate and the valve assembly.

Loosen the hose clamps and

remove the reinforced plastic

seawater intake and reject brine

hoses. See Figure R-1.

3. Use the 1/2" open-end wrench to

remove the four hex nuts securing

the pump back plate to the drive

assembly. Then pull the pump

away from the drive assembly to expose as much of the piston shaft as possible. Slide the black

rubber boot on the piston shaft toward the pump to expose the shaft coupling pin. Use a small

screwdriver or allen wrench to push the coupling pin out of the shaft. (Note: the coupling pin is a

loose fit and may fall out on its own.

Do not lose it.) Separate the pump

from the drive assembly and set the

drive assembly aside in a safe place.

Slide the black rubber boot off the

piston shaft. Move the pump to a

clean work surface for further

disassembly. See Figure R-2.

4. Remove the plastic intake hose barb

from the check valve plate. While

the pump is still bolted together, use

the 7/8" open-end wrench to just

loosen the tube fitting in the check

valve plate. Then use the 1/4" allen

wrench to remove the six sockethead

flange bolts that hold the check valve

plate to the pump body. Separate

the check valve plate from the pump

body and remove the large o-ring

(8012830) seal between them. See Figure R-2.

Produkt Specifikationer

Mærke:	Katadyn
Kategori:	Marine
Model:	REPAIR SEAL KIT PowerSurvivor 80E

Har du brug for hjælp?

Hvis du har brug for hjælp til Katadyn REPAIR SEAL KIT PowerSurvivor 80E stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Marine Katadyn Manualer

Katadyn PowerSurvivor 40E Manual

22 August 2024

Katadyn Siphon Manual

22 August 2024

Katadyn REPAIR SEAL KIT PowerSurvivor 80E Manual

22 August 2024

Katadyn PowerSurvivor 160E Manual

21 August 2024

Katadyn Bottle Manual

21 August 2024

Katadyn Micro Water Bottle Microfilter Manual

21 August 2024

Marine Manualer

Nyeste Marine Manualer

President PM 2010 WP Manual

15 Januar 2025

Rockford Fosgate PMX-8BB Manual

5 Oktober 2024

Simrad NSS Chartplotter Manual

23 September 2024

Rockford Fosgate PMX-2 Manual

21 September 2024

Rockford Fosgate T500X1br Manual

20 September 2024

Simrad NSS Manual

18 September 2024

Plastimo Echofish 300 Manual

27 August 2024

Silva S15 Manual

27 August 2024

Silva S15-N Navtex Manual

27 August 2024

IVT 8A Solar Manual

26 August 2024