Kelvinator KD12W Manual

Kelvinator Opvaskemaskine KD12W

Læs gratis den danske manual til Kelvinator KD12W (6 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Kelvinator KD12W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

.9.

.10.

Cleaning and Special Maintenance

Filter Assembly

For best performance and results, the filter assembly must be

cleaned.

The filter efficiently removes food particles from the wash water,

allowing it to be recirculated during the cycle. For this reason, it

is a good idea to remove the larger food particles trapped in the

filter after each wash cycle by rinsing the "A" semi-circular filter

and cup under running water. To remove the filter assembly, pull

on the cup handle in an upward direction. The entire filter assem-

bly (made up of the "A" semicircular filter and the "B" fine filter)

should be cleaned at least once a month. To clean the filter and

the fine filter, use a cleaning brush. Then, reassemble the filter

parts as shown in the figures below and inset the entire assem-

bly in the dishwasher, positioning in its seat and pressing

downward.

The dishwasher must never be used without the filters. Improper

replacement of the filters may reduce performance of the appli-

ance and damage dishes and utensils.

Cleaning the Spray Arms

It may happen that food particles become encrusted on the

sprayer arms and block the hole (see "Close up view [interior]"

on page 1, letters C-F ). Check the sprayer arms periodically and

clean them when needed.

It may occur that the dishwasher does not function properly or at

all. Before calling for assistance, Iet us see what can be done

first: Have you forgotten to press one of the buttons or to per-

form an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

Installation

Positioning the Appliance

Position the appliance in the desired location. The back should

rest against the wall behind it, and the sides, along the adjacent

cabinets or wall. The dishwasher is equipped with water supply

and drain hoses that can be positioned to the right or the left to

ensure correct installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them

in or out) to adjust the dishwasher, making it level. The appliance

should not be inclined more than 2 . If the appliance is level, it

will help ensure proper performance.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas) con-

nector and make sure that it is fastened tightly in place (see fig.

1).

If the water pipes are new or have not been used for an extended

period of time, let the water run to make sure that the water is

clear and free of impurities. If this precaution is not taken, there

is a risk that the water inlet can get blocked and damage the

appliance.

The connection must be made to the hot water line following the

same procedures as those for the connection to the cold water

line.

Drain Hose Connection

Insert the drain hose into a drain pipe with a minimum diameter

of 4cm, or let it run into the sink, making sure to avoid bending

or crimping it. Use the special plastic support that comes with

the appliance (see fig.2). The free end of the hose must be at a

height between 40 and 100 cm and must not be immersed in

water.

Attention:

The special plastic hose support must be solidly fastened to the

wall to prevent the drain hose from moving and allowing water to

spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for the

current in the home correspond to those on the rating plate

(located on the stainless steel inner door of the appliance) and

that the electrical system is sized for the maximum voltage on

the rating plate, insert the plug into an electrical socket which

is earthed properly (the earthing of the appliance is a safety

requirement mandated by law).

If the electrical socket to which the appliance must be connected

is not appropriate for the plug, replace the plug, rather than

using adaptors or the like as they could cause overheating and

burns.

Installation

Hot Water Connection

The water supply to the appliance can also be connected to the

house's hot water line (centralised system, heating system), as

long as it does not exceed a temperature of 60 .

In this case, the wash cycle time will be shortened by about 15

minutes and the wash efficiency slightly reduced.

MAX 100 MIN 40

ON OFF

60 60¡ª ¡ª 65¡ª 50¡ª

KD12W

fig.2

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the houses on and has sufficient pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;

- the rinse aid dosage is correct.

If, despite all these checks, the dishwasher still does not function

and/or the problem persists, contact the nearest authorised service

agent and provide them with the following information:

- the nature of the problem;

- the model type number (Mod...) and the serial number (S/N...),

which are indicated on the plate located on the side of the inner

part of the door.

Never call on unauthorised technicians and refuse to al-

low parts to be installed that are not original spare parts.

Troubleshooting

fig.1

Produkt Specifikationer

Mærke:	Kelvinator
Kategori:	Opvaskemaskine
Model:	KD12W

Har du brug for hjælp?

Hvis du har brug for hjælp til Kelvinator KD12W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Opvaskemaskine Kelvinator Manualer

Kelvinator LS KD 74/1 F Manual

15 Juli 2025

Kelvinator LS KD 74/1 Manual

15 Juli 2025

Kelvinator KD12WW Manual

15 Juli 2025

Kelvinator LS KD 74/1 G Manual

15 Juli 2025

Kelvinator KD12MM1 Manual

30 August 2024

Kelvinator KD12WW1 Manual

30 August 2024

Kelvinator KD14SS Manual

30 August 2024

Kelvinator KD12W Manual

30 August 2024

Kelvinator KD96-04S Manual

30 August 2024

Kelvinator KD12MM Manual

30 August 2024

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Proline DWP 1247 WH Manual

25 Oktober 2025

Westinghouse WSF6606XC Manual

21 Oktober 2025

Becken BBIDW5370 Manual

20 Oktober 2025

BEKO BDIN38441P Manual

15 Oktober 2025

Amica DFF61E4iISE Manual

15 Oktober 2025

Miele G 7186 SCVi AutoDos Manual

15 Oktober 2025

Siemens SF44T553EU Manual

12 Oktober 2025

Euro Appliances EDD60S Manual

11 Oktober 2025

Euro Appliances EDV604SS Manual

11 Oktober 2025

Miele G 5868 SCVi XXL Active Plus E Manual

11 Oktober 2025