Kicker 46HDR982 Manual

Kicker Hi-Fi system 46HDR982

Læs gratis den danske manual til Kicker 46HDR982 (18 sider) i kategorien Hi-Fi system. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Kicker 46HDR982, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/18
GETTING STARTED
1. Protect all painted surfaces
2. Remove seat and disconnect negative battery terminal. (Fig. 1)
a. On 2009 and later models, it will help to remove the two T40 bolts, the ECM and tray. (Fig. 2)
3. Remove windshield and outer fairing
a. Remove the six T25 fairing fasteners. (Fig. 3)
b. Remove the four turn signal fasteners and protect turn signal bodies while disassembled. (Fig. 4)
c. Disconnect both headlamps (the fairing and windshield come off as one piece.
SPEAKER REMOVAL/ INSTALLATION
4. Unplug both terminals on the left and right speakers.
5. Remove the four Phillips head fasteners that secure each speaker to the inner fairing (Fig. 5)
6. Install KICKER speakers with hardware removed in step 2 above making sure the speaker terminals are in the same location as the stock
speakers
AMP INSTALLATION
7. Remove the two 3/16” allen screws from the clutch side of the radio chassis.
8. Fasten the amplifi er bracket to the radio chassis with the hardware removed in step 1. (Fig. 6)
a. Remove any connectors that are mounted to the clutch side radio chassis and ensure the slotted hole on the amp bracket fi ts over
the front connector mounting tab.
9. Connect the electrical harness to the amplifi er. (Fig. 7)
10. Slide the connector side of the amp into the bracket ensuring that the amp body engages into the lip of the amp bracket. (Fig. 7)
11. Fasten amplifi er to the bracket with supplied hardware. (Fig. 7)
WIRE ROUTING
12. Following the color code, route the left and right side speaker wires safely to their respective speakers.
a. The throttle side speaker wires need to be routed behind the fairing hooks on the inner fairing bracket (where the main bundle of
wire is located). (Fig. 8)
13. Plug in the male ends into the stock harness, the terminals removed during speaker installation. (Fig. 9)
14. Plug the female ends onto the speaker terminals. (Fig. 9)
15. Locate the headlamp harness and remove the red cap over the Orange/White wire. If the Orange/White wire is currently in use (ex-acces-
sory lighting) unplug and connect to one of the blue wires from the Kicker harness. Plug the other blue wire from the Kicker harness into the
Orange/White wire, making sure it is fully engaged. (Fig.10)
16. Follow the proper procedure to remove the fuel tank.
17. Remove the electrical caddy lid. (Fig. 11)
18. Route the power harness on the clutch side of the frame neck, into the caddy and under the seat.
a. The power leads need to route into the inner fairing bracket where all of the other wires are entering and exiting the fairing.
b. Then they need to exit the bracket through the hole on the clutch side that is in front of the instrument cluster.
c. Lay them into the caddy area and remove the fuse during wire placement under the seat.
19. The blue lead under the seat would be used if installing a second amplifi er, but again, whether used or not, cover with heat shrink to
reduce the risk of a short. (Fig. 12)
20. Be sure to check that none of the wires will be in a bind when the steering head is turned fully to the right or the left.
96HDR982
Motorcycle Audio Kit Installation Guide for Harley Davidson®
Road Glide Motorcycles 1998–2013 (FLTR)
Package Contents:
(1) Install Guide (1) Wiring Harness (4) Black Cable Ties
(2) 5-1/4” KICKER Speakers (6) 8-32 x 1/2” Button Head Bolts (1) Amp Mounting Bracket
(1) 200W KICKER Amp (6) 8-32 Nylock Nuts (4) Black Heat Shrink
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper
procedures and torque specifi cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit may not
be compatible with some aftermarket head units.
SYSTEM SETUP
Note: KICKER recommends that the dip switches be set up as follows:
Auto turn-on - 12V Input level - HI HI-PASS - 80 Hz Input Gain control - 0  
21. Connect the battery terminals, install fuse, set gain to optimize system performance, and check audio system operation.
22. Disconnect negative battery terminal and carefully reassemble motorcycle.
23. Reconnect negative battery terminal, install seat and enjoy your KICKER audio system!
For questions, please contact KICKER Technical Support at 800-256-0808, M-F 8:00 am – 5:00 pm CST or email at support@kicker.com.
For installation videos please go to our Kicker YouTube channel.
KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 46HDR98-D-20120228
12 3 4
5 6 7 8
9 10 11 12

Produkt Specifikationer

Mærke: Kicker
Kategori: Hi-Fi system
Model: 46HDR982

Har du brug for hjælp?

Hvis du har brug for hjælp til Kicker 46HDR982 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Hi-Fi system Kicker Manualer

Kicker

Kicker 46HDTPH Manual

6 Oktober 2024
Kicker

Kicker PS42 Manual

22 September 2024
Kicker

Kicker 10PS5250 Manual

29 Juli 2024
Kicker

Kicker ZK 350 Manual

28 Juli 2024
Kicker

Kicker PS52504 Manual

28 Juli 2024
Kicker

Kicker 46HDR154 Manual

22 Juli 2024
Kicker

Kicker ZK 150 Manual

22 Juli 2024
Kicker

Kicker TRHDP Manual

18 Juli 2024
Kicker

Kicker 46HDS144 Manual

18 Juli 2024
Kicker

Kicker 46HDS962 Manual

18 Maj 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

Hamilton Buhl

Hamilton Buhl PA-25 Manual

30 Juli 2025
SSL

SSL SQ4 Manual

29 Juli 2025
SSL

SSL ML46DB Manual

29 Juli 2025
SSL

SSL ML39USA Manual

29 Juli 2025
SSL

SSL Evolution EV2.200 Manual

29 Juli 2025
SSL

SSL Evolution EV4.400 Manual

29 Juli 2025
Panasonic

Panasonic SH-ALL1CP Manual

29 Juli 2025
SSL

SSL ML42B Manual

29 Juli 2025
SSL

SSL Force F2.200 Manual

29 Juli 2025
Sony

Sony CMT-LX40i Manual

28 Juli 2025