Kicker zx 250 2 Manual

Kicker Bilradio zx 250 2

Læs gratis den danske manual til Kicker zx 250 2 (10 sider) i kategorien Bilradio. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Kicker zx 250 2, eller vil du spørge andre brugere om produktet?

Side 1/10
ZX
STEREOAMPLIFIER
ZX150.2, ZX200.2, ZX250.2
©2006 Stillwater Designs
English Version
Versión Español
Amplificador del la Serie ZX.2
Manual del Propietario
Deutsche Version
Stereoverstärker der ZX.2-Serie
Benutzerhandbuch
Version Française
Amplificateur de série ZX.2
Manuel d'utilisation
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's chassis. Adding an additional ground wire between the
battery's negative post and the vehicle chassis of this same gauge (or larger) is recommended.
Use a twisted pair of RCA (low-level)
interconnect cable to feed the audio signal
to the amplifier. Only use speaker wire
(high-level) inputs if your source unit does
not have RCA type outputs. Either input
method will provide a low-level output
signal at the RCA output, which effectively
passes the audio signal to another
amplifier or component (P.A.S.T.). Keep
the RCA cable away from factory wiring
harnesses and other power wiring. If you
need to cross this wiring, cross it at a 90
degree angle.
Install a fuse within 18” (45cm) of the
battery and in-line with the power cable
connected to your amplifier. If you ever need to remove the amplifier from the vehicle after it has been
installed, the ground wire should be the last wire disconnected from the amplifier--just the opposite as
when you installed it. See the chart below for power and ground wire size, and fusing
recommendations.
3. Configuration The following
diagrams show the most common
configurations for your Kicker ZX series amplifier.
Two Channel Operation (Stereo) These ZX amplifiers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) ZX.2 series amplifiers are capable of operating into a minimum
impedance of 4 ohms when in bridged operation. See Figure 3.
Stereo and Mono Operation Simultaneously (SAMS) The ZX.2 series amplifiers are capable of
operating into a minimum impedance of 4 ohms mono and 2 ohms per channel in stereo
simultaneously with the use of passive crossovers. See Figure 4.
INSTALLATION
ZX.2AMPLIFIER
ZX150.2 /ZX200.2 /ZX250.2
TwoChannelModels:
ZX.2SeriesAmplifier
Owner’sManual
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
__________________________
__________________________
__________________________
__________________________
SOURCE UNIT
killers trk7“on Top”
INPUT
RL
L+L- R+ R-
OUTPUT
RL
HI-LEVEL
INPUT
+ - - + OFF HI LO
XOVER
ModelZX150.2 Fuse25APowerGroundWire 8GA
ModelZX200.2 Fuse30APowerGroundWire 8GA
ModelZX250.2 Fuse40APowerGroundWire 8GA
24"
Or Less
(60cm)
Ground
+
_
+
_
R-
R+
L-
L+
Remote
Turn-On
Battery
+12V Fuse
Right Speaker
Left Speaker
18"
Or Less
Signal Out (P.A.S.T.)
(45cm)
Signal In
Minimum impedance of 2 ohms per channel in stereo operation
Remote
Turn-On
Battery
+12V Fuse
18"
Or Less
(45cm)
Minimum impedance of 4 ohms when in bridged operation
R-
R+
L-
L+
+
_
Mono
Speaker
Signal Out (P.A.S.T.)
Signal In
24"
Or Less
(60cm)
Ground
24"
Or Less
(60cm)
Ground
+
_
+
_+
_
HIGH PASS
CROSSOVER
HIGH PASS
CROSSOVER LOW
PAS S
CROSS-
OVER
Left Speaker
Right Speaker
Mono
Speaker
R-
R+
L-
L+
Remote
Turn-On
Battery
+12V Fuse
18"
Or Less
(45cm)
Minimum impedance of 4 ohms mono and 2 ohms per channel in
stereo simultaneously with the use of passive crossovers
Signal Out (P.A.S.T.)
Signal In
23
Figure 1
Figure 2
Figure 3
Figure 4
Use only one type of signal input to the amplifier,
either RCA Cable or Speaker Wire
RCA Cable
(Low-Level)
Input
Speaker Wire
(High-Level
Output)
Speaker Wire
(High-Level Input)
Left +
Left -
Right -
Right +
CONFIGURATION
RCA Cable
(Low-Level)
Output
Crossover Switch
Signal Out
(P.A.S.T.)
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.


Produkt Specifikationer

Mærke: Kicker
Kategori: Bilradio
Model: zx 250 2

Har du brug for hjælp?

Hvis du har brug for hjælp til Kicker zx 250 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Bilradio Kicker Manualer

Kicker

Kicker KX300.4 Manual

4 Oktober 2024
Kicker

Kicker IX 406 Impulse Manual

22 September 2024
Kicker

Kicker DX500.1 Manual

12 September 2024
Kicker

Kicker KX850.2 Manual

31 August 2024
Kicker

Kicker X50 Manual

23 August 2024
Kicker

Kicker zx 350 2 Manual

23 August 2024
Kicker

Kicker KX 400.4 Manual

22 August 2024
Kicker

Kicker ZX 300.1 Manual

22 August 2024
Kicker

Kicker kx 600 1 Manual

22 August 2024

Bilradio Manualer

Nyeste Bilradio Manualer