Klein Tools NCVT-2 Manual

Klein Tools Måleudstyr NCVT-2

Læs gratis den danske manual til Klein Tools NCVT-2 (8 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 67 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 34 anmeldelser. Har du et spørgsmål om Klein Tools NCVT-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

NON-CONTACT VOLTAGE TESTER

(NCVT-2) OwNER’S MANuAL

Fig. 1

Locking tab

Lengüeta de ﬁjación

Languette de

verrouillage

Probe

Punta de prueba

Sonde

Body /Cuerpo/Corps

Cap /Tapa/Capuchon

Power button

Botón de encendido

Interrupteur

Fig. 2

Gently push down on locking tab.

Empuje suavemente hacia abajo.

Appuyez doucement sur la languette de verrouillage.

AAAAAA

Fig. 4

While pushing down on tab, slide cap off body.

Mientras empuja hacia abajo sobre la lengüeta, deslice la

tapa hasta separarla del cuerpo.

Tout en appuyant sur la languette, faites glisser le capuchon

pour le détacher du corps du détecteur.

Align channel tabs on cap with slots on

tester body (one on each side of tester).

Alinee las lengüetas de canal ubicadas en la

tapa con las ranuras ubicadas en el cuerpo del

probador (una a cada lado del probador).

Alignez les languettes à proﬁlés sur le

capuchon avec les fentes du corps du dé-

tecteur (une de chaque côté du détecteur).

Slide cap onto body.

Deslice la tapa

sobre el cuerpo.

Faites glisser le capuchon

sur le corps du détecteur.

Align locking tab with cap.

Alinee la lengüeta de ﬁjación con la tapa.

Alignez la languette de verrouillage avec le capuchon.

Hold pocket-clip on cap close to tester body while sliding cap onto tester.

Sujete el clip para bolsillo ubicado en la tapa cerca del cuerpo del probador

mientras desliza la tapa sobre el probador.

Maintenez la pince-agrafe sur le capuchon à proximité du corps du détecteur

tout en faisant glisser le capuchon sur le détecteur.

Fig. 3

KLEIN TOOLS, INC.

Chicago, IL USA

www.kleintools.com

139805 Rev. 01/15 B

DuAL RANGE

MANUAL DEL USUARIO DEL PROBADOR DE TENSIÓN

SIN CONTACTOS DE INTERVALO DUAL (NCVT-2)

DéTECTEUR DE TENSION SANS CONTACT À

DOUBLE PLAGE (NCVT-2) - MODE D’EMPLOI

ENGLISH

SYMBOLS ON TESTER:

Warning. Risk of electric shock.

Risk of danger. Important information: It is important that users of this tester read,

understand, and follow all warnings, cautions, safety information, and instructions in this manual

before operating or servicing this tester. Failure to follow instructions could result in death or

serious injury.

Double Insulated.

Equipment is designed to protect against transients from the primary supply level.

(i.e. - electricity meter or overhead/ underground utility service).

OPERATING INSTRUCTIONS:

Modes of operation:

The NCVT-2 can operate as a dual range (NCVT-2 mode) or single range (NCVT-1 mode) tester. In

NCVT-2 mode, the tester will light a steady blue LED in the tip to indicate power-on and dual range

mode. In NCVT-1 mode, the tester will light a steady green LED in the tip to indicate power-on and

single range mode.

Turn unit on:

Press and hold the power button for ½ second, then release. Listen for single-beep sound and

watch for a steady green or blue LED to illuminate in the tip of the tester. The tester is now

activated and is operational. Test on known live circuit to verify tester functionality. See Silent

mode for additional power-on options.

Turn unit off:

Press and hold the power button for ½ second then release. Listen for a double-beep sound and

watch the green or blue LED turn off. The tester is now deactivated and is not operational.

System self-test:

The “power on” blue or green LED visually conﬁrms battery sufﬁciency, system integrity, and

operation/active mode. Always test on known live circuit to verify tester functionality prior to use.

Changing operation modes:

While the unit is powered on, press and hold the power button for 2 seconds. The power-on LED

will switch from blue to green or green to blue. The tester will start in whichever mode it was last

powered off in.

Checking for the presence of AC voltage:

Prior to use, test on known live circuit to verify tester functionality. Place tip of the tester near an

AC voltage and refer to the tables below for each mode:

NCVT-2 mode:

POWER-ON 12 TO 48 VOLTS AC 48 TO 1000 VOLTS AC

Audible

Single Beep Low-Pitched Pulsing Beeping Sound

High-Pitched Continuous Beeping Sound

Visual

Steady Blue LED

Blue LED Turns OFF and Red LED

Blinks (approx. 2-times per second).

Blue LED Turns OFF and Red LED

illuminates continuously.

NCVT-1 mode:

POWER-ON 12 TO 48 VOLTS AC 48 TO 1000 VOLTS AC

Audible

Single Beep No Sound

High-Pitched Continuous Beeping Sound

Visual

Steady Green LED Steady Green LED Green LED Turns OFF and Red LED

illuminates continuously.

In NCVT-2 mode, the tester will be more sensitive and will show voltage indication at a further

distance away from a high voltage source than in NCVT-1 mode. Use NCVT-1 mode in situations

where you expect the voltage source will be greater than 48V AC.

Low battery indication:

Scenario 1 – Powering on the tester: The “power on” LED in the tip of the tester changes from a

steady green or blue to a blinking green or blue and a series of beeping sounds is generated. The

tester then turns off. The unit is now deactivated and is not operational, the batteries require replace-

ment. To replace the tester batteries refer to the Maintenance section titled “Battery Replacement.”

Scenario 2 – Operating the tester: If the LED lights dim and the tone fades, the tester may require new

batteries. To replace the tester batteries refer to the Maintenance section titled “Battery Replacement.”

Auto Power Off:

After 4 minutes of non-use, the tester automatically powers off to conserve battery life. Listen for

a double-beep sound and watch the “power on” LED turn off. The tester is now deactivated and

is not operational.

Silent mode:

The tester can be operated with only visual indication of voltage. With the tester powered off, press

and hold the power button for 2 seconds then release.

MAINTENANCE:

Battery Replacement:

• Orient the tool/tester with the pocket-clip facing you.

• Gently depress the tab, Fig. 2, until you can slide the end-cap off the main body of the tester.

• Remove the batteries using caution to prevent damage or injury to the internal components.

• Replace with two 1.5V AAA or LR03 or NEDA 24A batteries.

• Place batteries into tester with the positive terminals facing the tip, Fig. 3.

• Carefully align and slide the end-cap to the body of the tester, Fig. 4. Push the cap until it is

fully seated (denoted by a clicking sound), Fig. 4.

• Note: Hold pocket-clip on cap close to tester body while sliding cap onto tester.

• Test on known live circuit to verify tester functionality.

CAT

Produkt Specifikationer

Mærke:	Klein Tools
Kategori:	Måleudstyr
Model:	NCVT-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Klein Tools NCVT-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måleudstyr Klein Tools Manualer

Klein Tools ET19 Manual

1 Januar 2025

Klein Tools NCVT-6 Manual

28 December 2024

Klein Tools ET18 Manual

21 September 2024

Klein Tools VDV211-048 Manual

21 September 2024

Klein Tools ET500 Manual

3 September 2024

Klein Tools ET510 Manual

3 September 2024

Klein Tools NCVT-3 Manual

3 September 2024

Klein Tools NCVT-2 Manual

3 September 2024

Klein Tools 45001 Manual

3 September 2024

Klein Tools HVNCVT-1 Manual

3 September 2024

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025