König TVS-KN-AVS500 Manual

König Ikke kategoriseret TVS-KN-AVS500

Læs gratis den danske manual til König TVS-KN-AVS500 (36 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om König TVS-KN-AVS500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/36

Please carefully read the following assembly,

installation and safety instructions for brackets.

Proper installation procedure should only be performed by an expert. Failure to do so

could result in serious personal injury.

This package includes all the mouting materials. Make sure that none of these parts

are missing or damaged before beginning the mounting. If there any parts missing or

damaged, please stop and contact your Brackets dealer.

Mounting Surface

• The enclosed accessories are only suitable for mounting to a ceiling or wall made of

solid concrete or wood studs. Do not install to sheet rock or wood panel.

• Make sure that the ceiling and/or wall can mount a redundant weight factor of 3 times

the total weight of the equipment you intend to support overhead or on the wall.

• Be aware of the weight of the equipment, and the potential for personal injury or damage

to the equipment if it is not adequately mounted.

General Guidelines

• Carefully determine the position you wish to mount the bracket and its distance from

the screen. For TV sets the distance should be approximately 3x screen diameter. For

projectors it is important to know the lens to screen distance (See projector speciﬁ cations

for set up).

• Attach the plate to the ceiling using all Lag Bolts as shown in the manual pages of the

model you are using.

• Warning! Tighten Lag Bolts until the wall plate is ﬁ rmly against the wall. DO NOT OVER

TIGHTEN!

• Tighten all nuts with the included wrench.

• Make sure the TV of Project bracket is mounted high enough to ensure people can

easily walk under it or walk by.

• Be sure to check you have mounted the appliance securely, so it will not fall.

• Make sure that the electric cord of the TV-Set or Projector is going straight to the

socket without hanging. In case you have spare cord, roll it and ﬁ rmly attached it to the

extension tube with tape.

• One month after installation and every six months after that, check that the TV-Set or

Projector mount is securely fastened to the wall or ceiling and that the screws and nuts

are not loosening. In case of loosening, tighten all the points that have loosend.

• For further assistance please call your local dealer or distributor shown on the invoice or

delivery note.

• Please keep the mounting instructions for later use or questions.

• Failure to do any of the above may result in failure and could be dangerous.

ENGLISH

Installation procedure

Step 1:

Invert the display and place it on a soft and ﬂ at surface. Locate the mounting points on

the back of the display.

Many LCD manufacturers conform to VESA standards. The VESA standard deﬁ nes

the physical mounting interfaces. The conforms to VESA 75/100/200/400 LCD mount

patterns.

monitors come with a random set of holes.Plasma

Note! Do not over tighten the screws. This may cause damage to the display or

bracket.

Before you begin, determine the desired mounting location.

Step 2:

Assemble the wall plate using the hardware and wrenches provided.

Note! Tighten screws uniformly to prevent distortion that might affect the assembly

process. Do not tighten with excessive force. Failure to follow these instructions may

cause excessive stress to the screws, greatly reducing their strength.

Solid concrete wall assembly: Carefully inspect the area where the LCD\Plasma\

Projector mount is to be installed. Check for any damage or loose cement.

Caution! When drilling holes in a cement wall or wooden studs, be absolutely sure there

are no water pipes or electrical wiring behind the wall. Use the wall plate to mark the

positions of the drilling holes.

Drill holes 3” deep using a (10 mm) masonry drill bit. Insert the plastic anchors into the

hole and tap ﬂ ush until the washer is even with the concrete surface. Place the back plate

onto the concrete surface and slowly tighten each nut onto its respective anchor.

Wood studs assembly:

Use a stud sensor (sold separately) to locate framing near the desired mounting position.

Note! Framing beams are typically 1-1/2”- 2” wide and spaced 16” on center. We

recommend locating more than one stud to ﬁ nd a trend in stud spacing. Using a sharp

device penetrate the drywall to identify the true center of the stud. Using the wall plate

base as a template, position the wall plate base vertically. Mark the hole position on

the wall, making sure you use the center screw holes. Use a level to check horizontal

alignment of marks.

Step 3:

For tilting models, gently pull the left and the right upper edges of the display to extend

the mount to its desired display tilting angle. Using a Phillips screwdriver, adjust the tilt

mechanism to its desired position. LCD mount models are designed to maintain their

tilting angle by using ﬁ nger tips on the back of the monitor. Keeping the display far from

the tilting mechanism, turn the Philips screw to its desired angle.

Step 4:

Once the mounting of the display is completed, you can tills move the display from side to

side to optimize the ﬁ nal position of the display. Gently slide the unit from left to right over

the steel rods on the wall plate.

Produkt Specifikationer

Mærke:	König
Kategori:	Ikke kategoriseret
Model:	TVS-KN-AVS500

Har du brug for hjælp?

Hvis du har brug for hjælp til König TVS-KN-AVS500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret König Manualer

König SAS-FIX11 Manual

20 August 2024

König ANT 117-KNL Manual

12 August 2024

König KNANIR2502B700 Manual

12 August 2024

König KNANIR2501B700 Manual

10 August 2024

König CMP-POWG41 Manual

5 August 2024

König KN-RFRO KIT Manual

4 August 2024

König SAS-ASSS300 Manual

27 Juli 2024

König SAS-DUMMYMS10 Manual

26 Juli 2024

König CSU3HDE35S100 Manual

25 Juli 2024

König CSBTTRNSM100 Manual

20 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MiVue 540 Manual

2 August 2025

Pro User PSI2000TX Manual

2 August 2025

Guede 5T Manual

2 August 2025

Navman EZY40 Manual

2 August 2025

Thule Chariot Ski kit Manual

2 August 2025

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025