Korg ToneWorks AX3B Manual
Læs gratis den danske manual til Korg ToneWorks AX3B (93 sider) i kategorien DJ udstyr. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Korg ToneWorks AX3B, eller vil du spørge andre brugere om produktet?
Side 1/93

Owner’s Manual
Manuel d’utilisation
Bedienungsanleitung


Table of Contents
Precautions ................................................................ 3
Introduction ............................................................... 4
Welcome! ......................................................................... 4
Main features ................................................................... 4
Front and rear panel .................................................. 4
Front panel ....................................................................... 4
Rear panel ....................................................................... 5
Setup ......................................................................... 5
Installing batteries ............................................................. 5
Basic connections .............................................................. 6
Example of a connection to a guitar amp ............................ 6
Example of a connection to a mixer or recorder .................. 6
Program mode ........................................................... 6
Selecting a program .......................................................... 7
Creating your sound (Edit mode) ................................. 7
Signal flow ....................................................................... 7
Selecting effects and adjusting the main parameters ............ 7
Selecting and adjusting sub-parameters .............................. 8
Saving a program (Write mode) ........................................ 8
Checking the values saved in a program (Original Value) .... 9
Bypass and Mute ....................................................... 9
Bypassing the AX3B .......................................................... 9
Muting the AX3B .............................................................. 9
Tuner ......................................................................... 9
Tuning procedure .............................................................. 9
Adjusting the tuner calibration ......................................... 10
Restoring the factory preset programs....................... 10
Troubleshooting ........................................................ 10
Specifications ........................................................... 11


3
AX3B Owner’s manual
Precautions
Location
Using the unit in the following locations can result in a malfunction.
• In direct sunlight
• Locations of extreme temperature or humidity
• Excessively dusty or dirty locations
• Locations of excessive vibration
• Close to magnetic fields
Power supply
Please connect the designated AC adapter to an AC outlet of the correct
voltage. Do not connect it to an AC outlet of voltage other than that for which
your unit is intended.
Interference with other electrical devices
Radios and televisions placed nearby may experience reception interference.
Operate this unit at a suitable distance from radios and televisions.
Handling
To avoid breakage, do not apply excessive force to the switches or controls.
Care
If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid
cleaners such as benzene or thinner, or cleaning compounds or flammable
polishes.
Keep this manual
After reading this manual, please keep it for later reference.
Keeping foreign matter out of your equipment
Never set any container with liquid in it near this equipment. If liquid gets into
the equipment, it could cause a breakdown, fire, or electrical shock.
Be careful not to let metal objects get into the equipment. If something does slip
into the equipment, unplug the AC adapter from the wall outlet. Then contact your
nearest Korg dealer or the store where the equipment was purchased.
THE FCC REGULATION WARNING (for U.S.A.)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses, and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Unauthorized changes or modification to this system can void the user’s
authority to operate this equipment.
CE mark for European Harmonized Standards
CE mark which is attached to our company’s products of AC mains operated
apparatus until December 31, 1996 means it conforms to EMC Directive (89/
336/EEC) and CE mark Directive (93/68/EEC).
And, CE mark which is attached after January 1, 1997 means it conforms to
EMC Directive (89/336/EEC), CE mark Directive (93/68/EEC) and Low Volt-
age Directive (73/23/EEC).
Also, CE mark which is attached to our company’s products of Battery oper-
ated apparatus means it conforms to EMC Directive (89/336/EEC) and CE
mark Directive (93/68/EEC).
IMPORTANT NOTICE TO CONSUMERS
This product has been manufactured according to strict specifications and
voltage requirements that are applicable in the country in which it is intended
that this product should be used. If you have purchased this product via the
internet, through mail order, and/or via a telephone sale, you must verify that
this product is intended to be used in the country in which you reside.
WARNING: Use of this product in any country other than that for which it is
intended could be dangerous and could invalidate the manufacturer’s or
distributor’s warranty.
Please also retain your receipt as proof of purchase otherwise your product
may be disqualified from the manufacturer’s or distributor’s warranty.
Company names, product names, and names of formats etc. are the trade-
marks or registered trademarks of their respective owners.
* Company names, product names, and names of formats etc. are the trade-
marks or registered trademarks of their respective owners.


4
Introduction
Welcome!
Thank you for adding the TONEWORKS AX3B Modeling Signal Proces-
sor to your r ig. Whether you’re playing live or in the studio, or practicing
with headphones, the AX3B will give you countless hours of great sounds!
To ensure a long and trouble-free relationship with your AX3B, please
read this manual carefully, and use it as directed. When you’ve finished
reading this manual, please keep it for future reference.
Main features
❑ Detailed and powerful modeling sounds delivered by Korg’s
modeling technology.
What is ?
(Resonant structure and Electronic circuit Modeling Sys-
tem) is KORG’s proprietary sound modeling technology which pre-
cisely reproduces the complex character and nature of both acoustic
and electric instruments as well as electronic circuits in real world
environments. emulates a wide variety of sound generation
characteristics including instrument bodies, speakers & cabinets,
acoustic fields, microphones, vacuum tubes, transistors, etc.
❑ 57 different modeling effect variations are built-in, and you can use
up to six different effects simultaneously (including noise reduction).
❑ You can edit all of the parameters for each effect in the four effect
categories (pre-effect, drive/amp, modulation, delay/reverb).
❑ Use these modeling effects to create your own sounds and store
them in internal memory as one of 40 user programs. In addition, 40
more programs are provided as presets for immediate use.
❑ Connect an optional Korg EXP-2 foot controller or XVP-10 expres-
sion/volume pedal, and use it as a wah pedal or volume pedal.
❑ The delay sound is preserved when you switch between programs
that have the same delay type and TIME parameter [P1] setting. Simi-
larly, the reverberation is preserved when switching between pro-
grams that have the same reverb type.
❑ A built-in auto chromatic tuner lets you tune while bypassed or muted.
Front and rear panel
This section explains the switches and connectors on the AX3B’s front
and rear panels.
Front panel
1
23
4
5
6
1. Function selector
The operation of the up/down buttons and value knob will depend on the
mode that’s chosen by this selector. You’re in Program mode when this
selector is at the [PROGRAM] position, Write mode when at the [WRITE]
position, and Edit mode when at the [PRE FX]–[DELAY/REV-PARAM]
positions.


5
AX3B Owner’s manual
2. Program/Value display
In Edit mode, this display indicates the effect type (F0–F9, d0–d5, A0–
A9, LE, nr, Cb), the parameter (P1–P4) or its setting (value).
In Write mode or Program mode, the display indicates the program num-
ber. When BYPASS/MUTE is active, the display indicates the name of
the note you’re tuning.
3. [▲(WRITE)], [▼(CANCEL)] buttons
In Effect mode, use these buttons to switch effect types or parameters.
By pressing the two buttons simultaneously, you can turn each effect
on/off. In Write mode, use these buttons to write a program.
In Program mode, you can press these buttons to increment or decre-
ment the program number in steps of 10. When you’re using the tuner,
use these buttons to adjust the calibration setting.
4. Value knob
In Edit mode, use this knob to adjust the value of a parameter. In Write
mode, you can use this knob to specify the writing-destination for the
program. In Program mode, this knob acts as the master volume.
5. Program Up switch
In Program mode, use this to select programs. The program number will
increase each time you press the switch. In Edit mode, press this to
make the parameter value appear in the program/value display. In this
case, the LED above the pedal will light, indicating that the program/
value display is showing the value of the effect parameter.
6. Program Down switch
In Program mode, use this to select programs. The program number will
decrease each time you press the switch. In Edit mode, press this to
make the effect or parameter type appear in the program/value display.
In this case, the LED above the pedal will light, indicating that the pro-
gram/value display is showing the type of effect or parameter.
Rear panel
1 2 34
1. Input jack
Connect your guitar to this jack.
2. Output jack
Connect this jack to your guitar amp or headphones.
3. Pedal jack
You can connect an optional Korg EXP-2 foot controller or XVP-10 ex-
pression/volume pedal to this jack.
A pedal connected here will function as a wah pedal if you’re using WAH
in [PRE FX], or as a volume pedal otherwise.
4. Power supply
~DC9V
You can connect an optional AC adaptor to this jack.
Setup
Installing batteries

6
1.
Slide the cover of the battery case in the direction of the arrow, and
open the cover.
Insert four separately sold AA-size alkaline batteries, being sure to
observe the correct polarity (“+” and “-” markings), and close the
battery case.
2.
When using batteries, the power will turn on when you insert a guitar
cable into the AX3B’s INPUT jack. While the power is on, the display
will indicate the program number or other information.
The power will turn off when you remove the cable from the INPUT jack.
Basic connections
Be sure to make all connections with the power turned off. If you fail to
use caution when making connections, you could damage your guitar
amp or speaker system, or cause malfunctions.
1.
Use a cable to connect the AX3B’s OUTPUT jack to your guitar
amp,mixer or recorder.
When making connections or turning on the power, lower the volume
of your amp or mixer so that you don’t hear noise
If you’re using headphones, plug them into the OUTPUT jack.
2.
Connect your guitar to the rear panel INPUT jack.
If you’re using batteries, this will turn the power on.
3.
If you’re using the optional AC adaptor, connect it to the rear panel
DC9V power supply jack, and then plug the adaptor into an AC out-
let to turn the power on.
4.
Raise the volume of your amp or mixer to the appropriate volume.
Example of a connection to a guitar amp
Bass amp
Pedal AC adaptor
to an AC outlet
Bass
INPUTOUTPUTPEDAL DC9V
Input
AX3B
Example of a connection to a mixer or recorder
Headphones
Digital recorder
AC adaptor
to an AC outlet
Bass
INPUTOUTPUT DC9V
AX3B
InputPhones
Program mode
Settings for each effect are collectively called a “program.”
The AX3B has 80 programs which 40 (01–40) of them are rewritable.
Programs 41–80 contain preset programs for immediate use.
In Program mode, you can select programs by pressing the Program


7
AX3B Owner’s manual
Down switch or Program Up switch, letting you change instantly between
sounds.
To enter Program mode, set the function selector to [PROGRAM]. (The
LEDs in the upper part of the Program Up/Down switches will light.)
Selecting a program
1.
Make sure that the function selector is set to [PROGRAM].
Make sure that the function selector is set to [PROGRAM].
In Program mode, the LEDs of both the Program Up and Program
Down switches will be lit.
When you turn on the power, you’ll be in Program mode regardless
of the position of the function selector.
2.
Turn the value knob to adjust the master volume.
If you've connected the AX3B to a guitar amp, set the master volume
to 50.
3.
Press the Program Up or Program Down switch to select a program.
The program/value display shows the number of the program you
selected.
Creating your sound (Edit mode)
Signal flow
PRE FX DRIVE/AMP CABINET
VOLUME PEDALMODDELAY / REVERB
NR
VOLUME PEDAL is available only if a pedal is connected to the PEDAL
jack.
Edit mode is when the function selector is in one of the [PRE FX]–[DE-
LAY/REV PARAM] positions.
You can change the effect type for each category ([PRE FX], [DRIVE/
AMP], [LEVEL/NR/CAB], [MOD], [DELAY/REV]), and edit the param-
eters to create your sound.
Selecting effects and adjusting the main
parameters
[PRE FX], [DRIVE/AMP], [MOD], [DELAY/REV]
To select the effect you want to use in each of the categories [PRE FX],
[DRIVE/AMP], [MOD], and [DELAY/REV], set the function selector to
the appropriate position and use the [ ] buttons.▲][▼
The program/value display will indicate a value of F0–F9 (in the case of
DRIVE/AMP, d0–d5 or A0–A9), and the LED at the top of the Program
Down pedal will light to indicate that the program/value display is show-
ing the effect type.
The effect list printed on the panel tells you the effect type that is se-
lected.
You can turn the value knob to adjust the “main” parameter for the se-
lected effect. At this time the program/value display will indicate the value
of the parameter, and the LED at the top of the Program Up pedal will
light to indicate that the program/value display is showing the parameter
value.
To turn an effect on/off, press both the [ ] and [ ] buttons simultaneously.▲ ▼
When an effect is on the effect type is shown, and when an effect is off
the display indicates “ ”.
■ Quick guide
When you select an effect, the AX3B automatically sets the parameters
of that effect to their most effective values. In other words, you can cre-
ate great sounds just by choosing an effect for each of the categories
PRE FX, DRIVE/AMP, MOD, and DELAY/REV, without having to make
detailed parameter settings.




11
AX3B Owner’s manual
❑ Are the DRIVE/AMP or PROGRAM LEVEL (LEVEL/NR/CAB) pa-
rameters be turned to a low value?
❑ Is the volume turned down for another effect?
❑ If an expression pedal is connected, is it turned down?
❑ Is the Mute function activated? Refer to “Bypass and Mute” (p.9)
and cancel the Mute function.
❑ Is the master volume turned down? Set the function selector to
[PROGRAM], and turn the value knob to adjust the master vol-
ume.
3. Effects don’t apply
❑ Could an effect be bypassed?
❑ Is the modulation “DEPTH” or the delay/reverb “MIX” set to a low
value?
❑ Is the AX3B in Bypass mode? Refer to “Bypass and Mute” (p.9)
and cancel the Bypass function.
4.
Sound connected to the guitar amp is distorted, or sounds
wrong
❑ Is the DRIVE/AMP [VOLUME] setting or the PROGRAM LEVEL
(LEVEL/NR/CAB) [LEVEL] setting raised excessively?
Specifications
Number of effects: Pre-effect types: 10
Drive/Amp Model types: 16
Cabinet Model types: 10
Modulation Effect types: 10
Delay Effect types: 5
Reverb Effect types: 5
Noise Reduction: 1
Number of programs: 80 (40 user/40 preset)
Audio input: INPUT (mono)
Audio output: OUTPUT (stereo)
Signal processing: A/D conversion: 24 bit
D/A conversion: 24-bit
Sampling frequency: 31.25 kHz
Tuner: Detection range : C0–C6
Calibration: A=438–445 Hz
Power supply: Four alkaline AA batteries (continuous use
of eight hours) or DC9V (separately sold)
AC adaptor
Dimensions (W ✕ ✕ D H): 178 ✕ ✕ 142 43 mm /
7.0 ✕ 5.6 ✕ 1.7 inches
Weight: 340 g / 11.99 oz.
Included items: Owner’s manual
Options (separately sold): DC9V AC adaptor
EXP-2 foot controller
XVP-10 expression/volume pedal
* Specifications and appearance are subject to change without notice for improve-
ment.


Sommaire
Précautions .............................................................. 13
Introduction ............................................................. 14
Bienvenue! ..................................................................... 14
Caractéristiques principales ............................................. 14
Panneau Avant et Arrière ......................................... 14
Panneau Avant ............................................................... 14
Panneau Arrière ............................................................. 15
Configuration ........................................................... 16
Installation des piles ........................................................ 16
Raccordements ............................................................... 16
Exemple de branchement à un ampli guitare ..................... 16
Exemple de branchement à une console de mixage ou d’un
enregistreur .................................................................... 16
Jouer (Mode Programme) ......................................... 17
Selectionner un programme ............................................. 17
Créez votre son (Mode Edit) ...................................... 17
Flux du Signal ................................................................ 17
Selectionner les effets et adjuster les paramètres principaux ...
17
Selectionner et adjuster les sous-paramètres ...................... 18
Sauvegarde d’un programme(Write mode) ....................... 19
Vérifiez les valeurs sauvées dans un programme (Valeur
originale) ....................................................................... 19
Bypass et Mute......................................................... 19
Bypasser l’AX3G ............................................................ 19
Muter l’AX3G ................................................................. 19
Accordeur ................................................................ 19
Procédure pour l’accord .................................................. 19
Ajustez le calibrage de l’accord .......................................20
Retour aux réglages d’usine ..................................... 20
Troubles de fonctionnement ...................................... 20
Caractéristiques ....................................................... 21


13
AX3B Manuel d’utilisation
Précautions
Emplacement
L’utilisation de cet instrument dans les endroits suivants peut en entraîner le
mauvais fonctionnement.
• En plein soleil
• Endroits très chauds ou très humides
• Endroits sales ou fort poussiéreux
• Endroits soumis à de fortes vibrations
• A proximité de champs magnétiques
Alimentation
Veuillez brancher l’adaptateur secteur spécifié sur une prise secteur à la ten-
sion appropriée. Ne branchez pas l’adaptateur sur une prise de courant dont
la tension ne correspond pas à celle pour laquelle l’appareil a été conçu.
Interférences avec d’autres appareils électriques
Les postes de radio et de télévision situés à proximité peuvent souffrir
d’interférences à la réception. Faites fonctionner cet appareil à une distance
raisonnable des postes de radio et de télévision.
Maniement
Pour éviter de les endommager, manipulez les commandes et les boutons de
cet instrument sans appliquer de force excessive.
Entretien
Lorsque l’extérieur est sale, essuyez-le avec un chiffon propre et sec. Ne
vous servez pas d’agents de nettoyage liquides comme du benzène ou du
diluant, des produits de nettoyage ou des vernis inflammables.
Conservez ce manuel
Après avoir lu ce manuel, veuillez le conserver soigneusement pour référence
ultérieure.
Évitez toute intrusion d’objets ou de liquide
Ne placez jamais de récipient contenant du liquide près de l’instrument. Si le
liquide pénètre dans l’appareil, il risque de provoquer des dommages, un
incendie ou une électrocution.
Veillez à ne pas laisser tomber d’objets métalliques dans le boîtier. Si cela se
produisait, débranchez l’adaptateur secteur de la prise de courant et contactez
votre revendeur Korg le plus proche ou le magasin où vous avez acheté
l’instrument.
Marque CE pour les normes européennes harmonisées
La marque CE apposée sur tous les produits de notre firme fonctionnant
sur secteur jusqu’au 31 décembre 1996 signifie que ces appareils répondent
à la Directive EMC (89/336/CEE) et à la Directive concernant la marque
CE (93/68/CEE).
La marque CE apposée après le 1 janvier 1997 signifie que ces appareils
sont conformes à la Directive EMC (89/336/CEE), à la Directive concernant
la marque CE (93/68/CEE) ainsi qu’à la Directive Basse Tension (73/23/
CEE).
La marque CE apposée sur tous les produits de notre firme fonctionnant
sur piles signifie que ces appareils répondent à la Directive EMC (89/336/
CEE) et à la Directive concernant la marque CE (93/68/CEE).
REMARQUE IMPORTANTE POUR LES CLIENTS
Ce produit a été fabriqué suivant des spécifications sévères et des besoins
en tension applicables dans le pays où ce produit doit être utilisé. Si vous
avez acheté ce produit sur internet, par correspondance ou/et au téléphone,
vous devez vérifier que ce produit est bien utilisable dans votre pays de
résidence.
ATTENTION: L’utilisation de ce produit dans un pays autre que celui pour
lequel il a été conçu peut être dangereuse et annulera la garantie du
fabricant ou du distributeur.
Veuillez aussi conserver votre récépissé qui est la preuve de votre achat,
faute de quoi votre produit risque de ne plus être couvert par la garantie du
fabricant ou du distributeur.
* Les noms de societes, nomsm de produits et noms de formats, etc. dans
ce manuel sont des marques de fabrique ou des mar-ques deposees de
leurs proprietaires respectifs.


15
AX3B Manuel d’utilisation
position (WRITE) et en mode d’édition lorsque le sélecteur est sur la
position [PRE FX]–[DELAY/REV-PARAM].
2. Program/Value display
En mode d’édition, l’afficheur indique le type d’effet (F0–F9, d0–d5, A0–
A9, LE, nr, Cb), les paramètres (P1–P4) ou la configuration (value). Dans
le mode Write ou Program, l’afficheur indique le numéro de programme.
Lorsque la fonction BYPASS/MUTE est activée, l’afficheur indique le
nom de la note pour l’accordage.
3. Boutons [▲(WRITE)], [▼(CANCEL)]
Dans le mode Effect, utilisez ces boutons pour commuter les types d’effet
ou les paramètres. En pressant simultanément les deux boutons, vous
pouvez activer ou désactiver les effets. Dans le mode Write, utilisez ces
boutons pour enregistrer un programme. Dans le mode Program, vous
pouvez presser ces boutons pour incrémenter ou décrémenter le
programme par pas de 10. lorsque vous utilisez l’accordeur, ces boutons
ajustent la calibration de l’accord.
En mode d’édition, utilisez le potentiomètre pour ajuster la valeur du
paramètre. Dans le mode WRITE, vous pouvez utiliser ce potentiomètre
pour spécifier la destination de mémoire d’écritures pour la mémorisation
du programme. Dans le mode Program, ce potentiomètre a la fonction
de master volume.
4. Value knob
Dans le mode Edit, utilisez ce potentiomètre pour ajuster la valeur d’un
paramètre. Dans le mode Write, vous pouvez employer ce potentiomètre
pour indiquer la destination de l’écriture du programme. En mode
Programme, ce potentiomètre a la fonction de master volume.
5. Program Up switch
Dans le mode Program, utilisez ce commutateur pour sélectionner un
programme. Le numéro de programme s’incrémentera chaque fois que
vous appuierez sur ce switch. En mode Edit, en appuyant sur ce switch
fera apparaître sur l’afficheur la valeur du paramètre du programme.
Dans se cas-ci, la LED au-dessus du switch s’allumera, indiquant sur
l’affichage la valeur du paramètre d’effet du Program/Value.
6. Program Down switch
Dans le mode Program, utilisez ce commutateur pour sélectionner un
programme. Le numéro de programme se décrémentera chaque fois
que vous appuierez sur ce switch. En mode Edit, en appuyant sur ce
switch fera apparaître sur l’afficheur le type d’effet du programme. Dans
ce cas-ci, la LED au-dessus du switch s’allumera, indiquant sur l’affichage
le type d’effet du programme.
Panneau Arrière
1 2 34
1. Prise INPUT
Raccordez votre guitare à cette prise.
2. Prise OUTPUT
Raccordez cette prise à votre amplificateur de guitare.
3. Prise pour pédale d’expression
Si vous souhaitez utiliser une pédale d’expression au pied pour com-
mander le volume ou le Wah-Wah, vous pouvez connecter une pédale
Korg optionnelle EXP-2 ou XVP-10 sur cette prise.
4. Prise d’alimentation secteur
~DC9V
L’adaptateur secteur vendu séparément peut être branché sur cette prise.




20
Si vous voulez accorder sans produire de sons, comme par exemple
lors d’un concert, vous voudrez probablement mettre l’AX3B en po-
sition Mute.
2.
Jouez une note avec votre guitare. L’écran program/value indiquera
le nom de la note la plus proche.
Le nom des notes est indiqué comme suit:
C C# D D# E F F# G G# A A# B
nom des notes
Affichage
3.
Si votre guitare est trop haute la led Program Up clignotera. Si votre
guitare est trop basse, la led Program Down clignotera. Dans d’autres
cas, un clignotement rapide indiquera que votre guitare est proche
de la note juste.
Quand l’accord est parfait, les Leds Program Up et Down clignotent
simultanément.
Ajustez le calibrage de l’accord
Quand vous allumez l’AX3B, l’accordeur interne est réglé sur la note de
référence (le LA) à 440Hz. Vous pouvez ajustez cette note de référence
dans une échelle comprise entre 438 Hz et 445 Hz.
Quand l’accordeur est actif, vous pouvez utiliser les boutons [ ] pour▲][▼
ajuster la note de référence dans une échelle comprise entre 438 Hz–
445 Hz. En faisant ainsi, l’écran program/value indiquera une valeur
comprise entre 38–45.
Quand vous éteignez l’appareil, l’ajustement du pitch que vous aurez
effectué sera éffacé. Le réglage à 440 Hz sera systématiquement rappelé.
Retour aux réglages d’usine
Voici comment retrouver les réglages d’usine de l’AX3B’s ainsi que les
programmes d’origine.
Quand vous excecutez cette fonction, tous les programmes que vous
aurez créés seront effacés et remplacés par les programmes d’usine.
1.
Appuyes simultanément sur les boutons Program Up et Down et
[▼(CANCEL)] button (3 boutons au total), Allumez l’appareil. L’écran
program/value display indiquera “ ”, et les Leds de la partie
superieure du bouton Program Up/Downvont clignoter. . vous pouvez
relacher les 3 boutons.
2.
Si vous ne voulez pas de cette opération, pressez sur le bouton
[CANCEL].
3.
Pressez le bouton [ (WRITE)] . L’écran program/value indiquera▲
“ ” et le chargement va commencer. Quand il sera complet, l’écran
indiquera “ ”, et l’AX3B entrera automatiquement dans le mode program.
Ne jamais éteindre l’appareil quand il se recharge.
Troubles de fonctionnement
Avant de suspecter une panne, veuillez s’il vous plait vérifier les points
suivants. Si vous n’arrivez pas malgré tout à résoudre le problème,
contactez votre revendeur.
1 Pas d’allumage
❑
Les piles ne sont elles pas trop faibles? Quand la capacité des piles
diminue, l’écran va clignoter “ ”. Nous recommandons de changer
les piles dès que possible. Si les piles sont vides, ôtez les
immédiatement. Laisser des piles usagées dans l’appareil peut causer
des disfonctionnements (coulage par exemple). Vous devez ôter les
piles si vous ne devez pas utiliser l’AX3B pour une longue periode.


23
AX3B Bedienungsanleitung
Vorsichtsmaßregeln
Verwendungsort
Bei Verwendung des Geräts an den folgenden Orten kann eine Fehlfunktion
auftreten.
• Im direkten Sonnenlicht
• An Orten mit extremer Temperatur oder Luftfeuchtigkeit
• An sehr staubigen oder schmutzigen Orten
• An Orten mit starker Vibration
• In der Nähe von Magnetfeldern
Stromversorgung
Schließen Sie das spezielle Netzteil an eine Netzsteckdose mit der richtigen
Netzspannung an. Schließen Sie es nicht an eine Steckdose mit einer anderen
Spannung als der für das Gerät geeigneten an.
Störungen mit anderen elektrischen Geräten
In der Nähe aufgestellte Radio- oder Fernsehgeräte können
Empfangsstörungen aufweisen. Betreiben Sie dieses Gerät immer in einem
geeigneten Abstand von Radio- oder Fernsehgeräten.
Behandlung
Um Beschädigungen zu vermeiden, betätigen Sie Schalter oder
Bedienungselement nicht mit Gewalt.
Pflege
Wenn das Äußere schmutzig wird, mit einem sauberen, trockenen Lappen
abwischen. Verwenden Sie keine flüchtigen organischen Lösungsmittel wird
Benzol, Terpentin, Reinigungslösungen oder entflammbare Poliermittel.
Die Anleitung aufbewahren
Nach dem Lesen dieser Anleitung bewahren Sie sie bitte zum Nachschlagen
auf.
Fremdkörper aus dem Gerät halten
Stellen Sie niemals Behälter mit Flüssigkeiten in der Nähe des Geräts ab.
Wenn Flüssigkeit in das Gerät eindringt, kann ein Geräteausfall, Brand oder
elektrischer Schlag verursacht werden.
Achten Sie darauf, keine Metallobjekte in das Gerät kommen zu lassen. Falls
ein Gegenstand in das Gerät eindringt, ziehen Sie das Netzteil von der
Steckdose ab. Dann wenden Sie sich an Ihren Korg-Fachhändler oder an des
Geschäft, in dem das Gerät gekauft wurde.
CE-Kennzeichen für europäische harmonisierte Standards
Das CE-Kennzeichen, dass an den mit Netzstrom betriebenen Produkten
unserer Firma, hergestellt bis zum 31. Dezember 1996, angebracht ist,
zeigt an, dass das betreffende Gerät mit der EMV-Richtlinie (89/336/EWG)
und der CE-Kennzeichen-Richtlinie (93/68/EWG) übereinstimmt.
Das nach dem 1. Januar 1997 angebrachte CE-Kennzeichen weist auf
Übereinstimmung mit der EMV-Richtlinie (89/336/EWG), CE-Kennzeichen-
Richtlinie (93/68/EWG) und Niederspannungsrichtlinie (73/23/EWG) hin.
Außerdem zeigt das CE-Kennzeichen, dass an den mit Batteriestrom
betriebenen Produkten unserer Firma angebracht ist, an dass das
betreffende Gerät mit der EMV-Richtlinie (89/336/EWG) und der CE-
Kennzeichen-Richtlinie (93/68/EWG) übereinstimmt.
WICHTIGER HINWEIS FÜR KUNDEN
Dieses Produkt wurde unter strenger Beachtung von Spezifikationen und
Spannungsanforderungen hergestellt, die im Bestimmungsland gelten.
Wenn Sie dieses Produkt über das Internet, per Postversand und/oder mit
telefonischer Bestellung gekauft haben, müssen Sie bestätigen, dass dieses
Produkt für Ihr Wohngebiet ausgelegt ist.
WARNUNG: Verwendung dieses Produkts in einem anderen Land als dem,
für das es bestimmt ist, verwendet wird, kann gefährlich sein und die
Garantie des Herstellers oder Importeurs hinfällig lassen werden.
Bitte bewahren Sie diese Quittung als Kaufbeleg auf, da andernfalls das
Produkt von der Garantie des Herstellers oder Importeurs ausgeschlossen
werden kann.
* Die ubrigen in dieser Bedienungsanleitung erwahnten Firmen-, Produkt-,
Formatnamen usw. sind Warenzeichen oder eingetra-gene Warenzeichen
der rechtlichen Eigentumer und werden ausdrucklich anerkannt.



Produkt Specifikationer
Mærke: | Korg |
Kategori: | DJ udstyr |
Model: | ToneWorks AX3B |
Har du brug for hjælp?
Hvis du har brug for hjælp til Korg ToneWorks AX3B stil et spørgsmål nedenfor, og andre brugere vil svare dig
DJ udstyr Korg Manualer
1 Februar 2025
26 Januar 2025
28 Maj 2024
23 April 2024
18 April 2024
8 April 2024
5 April 2024
1 April 2024
4 Februar 2024
11 Januar 2024
DJ udstyr Manualer
- AlphaTheta
- Gemini
- Pioneer
- DTronics
- ION
- Arturia
- Native Instruments
- König
- Denver
- Zoom
- Thomson
- RME
- Dual
- Roland
- Thorens
Nyeste DJ udstyr Manualer
16 Juni 2025
9 Juni 2025
9 Juni 2025
3 Juni 2025
30 Marts 2025
30 Marts 2025
8 Marts 2025
19 Februar 2025
18 Februar 2025
18 Februar 2025