Leisure VUN1160 Manual

Leisure Køkkenvask VUN1160

Læs gratis den danske manual til Leisure VUN1160 (4 sider) i kategorien Køkkenvask. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Leisure VUN1160, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

05/04 1978

Any machining operation will produce ﬁ ne particles of dust.

Drilling or cutting must be carried out in a well-ventilated

area.

2. Position clips over pins moulded in sink. The clips are pulled

& twisted towards the edge of the sink as shown in ﬁ g. 2.

If a clip is tight tap on with ﬂ at head screwdriver as shown in

ﬁ g. 2A and hinge

them back away

from sink edge.

3. At thi s p oin t

try the sink in

t h e c u t - o u t ,

some localised

enlargement of the hole may be necessary around the

clips.

4. Fit the tap to the sink.

5. Fit the wastes to the sink following the instructions packed

with them.

6. Fit the foam seal to the edge of the sink. Peel off the paper

backing strip and stick the seal to the recess in the sink as

shown in ﬁ g. 3. Ensure that a neat butt joint is achieved

where the ends of the seal meet.

FITTING THE SINK

1. Position the sink in the cut out.

2. Tension the ﬁ xing clips as shown

in ﬁ g. 4. Ensure that the foam

seal is carefully compressed but

do not overtighten the clips.

3. Complete the plumbing of the

hot and cold supply to the tap.

IMPORTANT

This sink has been coated with

a thin layer of protective ﬁ lm.

It is essential that the sink be

cleaned with cream cleaner (i.e. Cif Cleaner) before use.

INSTALLATION DETAILS FOR SNAP ON FIXING SYSTEM

VELSTRA & NEOSTONE SINKS

NOTE: During installation care should be taken to ensure

the sink is protected from scuffs and scratches. Straining and

overtightening of all plumbing ﬁ xtures connected to the sink

should be avoided. Installers should carefully check that the

moulding and the edges of the sink are dead level so that

water will ﬂ ow off the drainer.

PLEASE READ THOROUGHLY BEFORE

ATTEMPTING TO INSTALL SINK.

PREPARING THE WORKTOP

1. It is recommended that the inset sink is ﬁ tted to the worktop

before being permanently ﬁ xed to the cabinet.

2. Place the sink upside down on worktop. Position the sink

relative to the worktop as required, ensuring that the cabinet

framework will be clear of all parts of the sink.

With a sharp soft pencil draw round sink as accurately as

possible. See ﬁ g. 1.

3. Remove the sink and draw another line 10mm inside

the out-line of the sink top. This is the cutting line for the

aperture.

4. Drill as large a hole as possible inside the cutting line. Using

a pad saw, jigsaw or similar, cut out the aperture. At this

point we would recommend that the worktop aperture is

sealed. To do this paint over with a p.v.a. adhesive, paint,

varnish or smear with silicone sealant.

PREPARING THE SINK

1. If a taphole is required, but has not been supplied in the

sink, proceed as follows:

Decide whether the bowl is to be left or right hand when

sink is ﬁ tted. Cut the appropriate taphole into the sink

using a 35mm hole

saw (supplied with

selected product).

On the reverse side

of the sink there

is a location hole

this is to be used

for positioning the

hole saw as shown

in ﬁ g. 1A.

Before drilling please read safety instructions supplied

with hole saw.

Front face must be fully supported to prevent cracking

carefully drill out taphole.

Warning: Velstra & Neostone products include a silica ﬁ ller.

05/04 1978

ALTERNATIVE METHOD OF SEALING

VELSTRA® & NEOSTONE SINKS

1. Apply silicone sealant (not supplied) to the underside of

the sink rim, as shown in ﬁ g. 5.

2. Remove surplus sealant from around the sink using a damp

cloth.

VELSTRA AND NEOSTONE CARE INSTRUCTIONS

Congratulations on purchasing your new sink. Vel-

stra and Neostone are revolutionary sink materials

that are extremely robust and hard wearing. How-

ever both materials will beneﬁ t from a little care

and attention to ensure lasting good looks and per-

formance. Please read the following care advice

carefully.

Cleaning

For every day cleaning a damp cloth with ordinary

washing up liquid will sufﬁ ce. Heavier staining can

be removed with a cream cleaner eg. Cif on a damp

cloth. Really stubborn stains should be treated to

an overnight soaking in diluted bleach. Please do

not use abrasive powders or steel scouring pads

as they may affect the surface gloss. Do not at-

tempt to remove limescale by scraping it off, an

application of citric acid (lemon juice) should, with

the help of a stiff brush, remove any deposits. Sil-

ver streaks on the surface of the sink are caused

by aluminium utensils and are not scratches, they

can be easily removed with a cream cleaner.

Heat Resistance

Velstra and Neostone are highly resistant to ex-

tremes of temperature and will withstand hot pans

up to 230°C but avoid pans containing very hot oil

above this temperature.

Chemical Resistance

Velstra and Neostone are resistant to just about

any chemical found in the home, but be careful,

these days waste systems are made from plastic

materials which may not be. The coloured wastes

supplied as standard with the sink, are made from

a tough plastic material but these are not resistant

to some solvents, especially nail varnish remover,

acetone and nitro thinners.

Further Advice

Do not use the drainer as a chopping board. A hard

wood chopping board or polyethylene food board

is available as an optional extra.

Avoid plastic washing up bowls, they pick up ﬁ ne

particles of grit which transforms them into very

efﬁ cient grinding surfaces causing wear on your

sink. We recommend a rubber mat in this case.

20 Year Guarantee

We guarantee to replace any Velstra or Neostone

sink that breaks due to material or manufacturing

defects within 20 years from the date of purchase.

The guarantee does not cover normal wear and

tear occurring through use of the product.

For the guarantee to apply the owner must follow

the use, care and cleaning instructions provided.

Accessories and waste ﬁ ttings are not included in

this guarantee.

Produkt Specifikationer

Mærke:	Leisure
Kategori:	Køkkenvask
Model:	VUN1160
Bredde:	1160 mm
Dybde:	508 mm
Produktfarve:	Hvid
Første skål, dybde:	180 mm
Anden skål, dybde:	160 mm
Første skål, dimensioner (BxL):	408 x 424 mm
Anden skål, dimensioner (BxL):	272 x 424 mm
Antal vaskeskåle:	2 skåle
Vask, type:	Top-monteret vask
Vask form:	Rektangulær
Facon på første vask:	Rektangulær
Facon på anden vask:	Rektangulær
Vandhane, hul:	Ja
Drænebræt:	Ja
Antal huller til haner:	2
Størrelse på vandhane:	35 mm