Lincoln Electric Magnum 100SG Manual

Lincoln Electric Svejseapparat Magnum 100SG

Læs gratis den danske manual til Lincoln Electric Magnum 100SG (118 sider) i kategorien Svejseapparat. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Lincoln Electric Magnum 100SG, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/118

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

MAGNUM

100SG SPOOL GUN

OPERATOR’S MANUAL

IMT913-A

August, 2010

Safety Depends on You

Lincoln arc welding and cutting

equipment is designed and built

with safety in mind. However,

your overall safety can be

increased by proper installation ...

and thoughtful operation on your

part. DO NOT INSTALL, OPER-

ATE OR REPAIR THIS EQUIP-

MENT WITHOUT READING

THIS MANUAL AND THE

SAFETY PRECAUTIONS CON-

TAINED THROUGHOUT. And,

most importantly, think before you

act and be careful.

FORENGINE

poweredequipment.

1.a.Turntheengineoffbeforetroubleshootingandmaintenance

workunlessthemaintenanceworkrequiresittoberunning.

____________________________________________________

1.b.Operateenginesinopen,well-ventilated

areasorventtheengineexhaustfumes

outdoors.

____________________________________________________

1.c.Donotaddthefuelnearanopenflameweld-

ingarcorwhentheengineisrunning.Stop

theengineandallowittocoolbeforerefuel-

ingtopreventspilledfuelfromvaporizingon

contactwithhotenginepartsandigniting.Do

notspillfuelwhenfillingtank.Iffuelisspilled,

wipeitupanddonotstartengineuntilfumes

havebeeneliminated.

____________________________________________________

1.d.Keepallequipmentsafetyguards,coversanddevicesinposi-

tionandingoodrepair.Keephands,hair,clothingandtools

awayfromV-belts,gears,fansandallothermovingparts

whenstarting,operatingorrepairingequipment.

____________________________________________________

1.e.Insomecasesitmaybenecessarytoremovesafety

guardstoperformrequiredmaintenance.Remove

guardsonlywhennecessaryandreplacethemwhenthe

maintenancerequiringtheirremovaliscomplete.

Alwaysusethegreatestcarewhenworkingnearmoving

parts.

___________________________________________________

1.f.Donotputyourhandsneartheenginefan.

Donotattempttooverridethegovernoror

idlerbypushingonthethrottlecontrolrods

whiletheengineisrunning.

___________________________________________________

1.g.Topreventaccidentallystartinggasolineengineswhile

turningtheengineorweldinggeneratorduringmaintenance

work,disconnectthesparkplugwires,distributorcapor

magnetowireasappropriate.

SAFETY

ARCWELDINGCANBEHAZARDOUS.PROTECTYOURSELFANDOTHERSFROMPOSSIBLESERIOUSINJURYORDEATH.

KEEPCHILDRENAWAY.PACEMAKERWEARERSSHOULDCONSULTWITHTHEIRDOCTORBEFOREOPERATING.

Readandunderstandthefollowingsafetyhighlights.Foradditionalsafetyinformation,itisstronglyrecommendedthatyou

purchaseacopyof“SafetyinWelding&Cutting-ANSIStandardZ49.1”fromtheAmericanWeldingSociety,P.O.Box351040,

Miami,Florida33135orCSAStandardW117.2-1974.AFreecopyof“ArcWeldingSafety”bookletE205isavailablefromthe

LincolnElectricCompany,22801St.ClairAvenue,Cleveland,Ohio44117-1199.

BESURETHATALLINSTALLATION,OPERATION,MAINTENANCEANDREPAIRPROCEDURESARE

PERFORMEDONLYBYQUALIFIEDINDIVIDUALS.

WARNING

ELECTRICAND

MAGNETICFIELDS

maybedangerous

2.a.Electriccurrentflowingthroughanyconductorcauses

localizedElectricandMagneticFields(EMF).Welding

currentcreatesEMFfieldsaroundweldingcablesand

weldingmachines

2.b.EMFfieldsmayinterferewithsomepacemakers,and

weldershavingapacemakershouldconsulttheirphysician

beforewelding.

2.c.ExposuretoEMFfieldsinweldingmayhaveotherhealth

effectswhicharenownotknown.

2.d.Allweldersshouldusethefollowingproceduresinorderto

minimizeexposuretoEMFfieldsfromtheweldingcircuit:

2.d.1.

Routetheelectrodeandworkcablestogether-Secure

themwithtapewhenpossible.

2.d.2.Nevercoiltheelectrodeleadaroundyourbody.

2.d.3.Donotplaceyourbodybetweentheelectrodeand

workcables.Iftheelectrodecableisonyourright

side,theworkcableshouldalsobeonyourrightside.

2.d.4.Connecttheworkcabletotheworkpieceascloseas

possibletotheareabeingwelded.

2.d.5.Donotworknexttoweldingpowersource.

1.h.Toavoidscalding,donotremovethe

radiatorpressurecapwhentheengineis

hot.

ForDieselEngines:Dieselengineexhaustand

someofitsconstituentsareknowntotheState

ofCaliforniatocausecancer,birthdefects,and

otherreproductiveharm.

ForGasolineEngines:Theengineexhaustfrom

thisproductcontainschemicalsknowntothe

StateofCaliforniatocausecancer,birthdefects,

orotherreproductiveharm.

CALIFORNIAPROPOSITION65WARNINGS

FOR ENGINE

powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance

work unless the maintenance work requires it to be running.

____________________________________________________

1.b.Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame weld-

ing arc or when the engine is running. Stop

the engine and allow it to cool before refuel-

ing to prevent spilled fuel from vaporizing on

contact with hot engine parts and igniting. Do

not spill fuel when filling tank. If fuel is spilled,

wipe it up and do not start engine until fumes

have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in posi-

tion and in good repair.Keep hands, hair, clothing and tools

away from V-belts, gears, fans and all other moving parts

when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove

guards only when necessary and replace them when the

maintenance requiring their removal is complete.

Always use the greatest care when working near moving

parts.

___________________________________________________

1.f. Do not put your hands near the engine fan.

Do not attempt to override the governor or

idler by pushing on the throttle control rods

while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenance

work, disconnect the spark plug wires, distributor cap or

magneto wire as appropriate.

SAFETY

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.

KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you

purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040,

Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the

Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

WARNING

ELECTRIC AND

MAGNETIC FIELDS

may be dangerous

2.a. Electric current flowing through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and

welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health

effects which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right

side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as

possible to the area being welded.

2.d.5. Do not work next to welding power source.

1.h. To avoid scalding, do not remove the

radiator pressure cap when the engine is

hot.

For Diesel Engines: Diesel engine exhaust and

some of its constituents are known to the State

of California to cause cancer, birth defects, and

other reproductive harm.

For Gasoline Engines: The engine exhaust from

this product contains chemicals known to the

State of California to cause cancer, birth defects,

or other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNINGS

OPERATOR’S MANUAL

Produkt Specifikationer

Mærke:	Lincoln Electric
Kategori:	Svejseapparat
Model:	Magnum 100SG

Har du brug for hjælp?

Hvis du har brug for hjælp til Lincoln Electric Magnum 100SG stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Svejseapparat Lincoln Electric Manualer

Lincoln Electric Square Wave TIG 200 Manual

24 September 2025

Lincoln Electric Flextec 500X CE Manual

24 September 2025

Lincoln Electric Flextec 350X PowerConnect Manual

24 September 2025

Lincoln Electric NA-4 Manual

23 September 2025

Lincoln Electric Magnum 100SG Manual

23 September 2025

Lincoln Electric Ranger 305 G EFI Manual

23 September 2025

Lincoln Electric Flextec 650X CE Manual

23 September 2025

Lincoln Electric Tandem Cruiser Manual

8 September 2025

Lincoln Electric Power Wave Advanced Module Manual

8 September 2025

Lincoln Electric Ranger Air 260MPX Manual

8 September 2025

Svejseapparat Manualer

Nyeste Svejseapparat Manualer

Draper 53084 Manual

23 September 2025

Draper Storm Force 02516 Manual

23 September 2025

23 September 2025

23 September 2025

11 September 2025

7 September 2025

7 September 2025

Stanley Star 7000 Manual

6 September 2025

Scheppach WSE3500 Manual

1 September 2025

GYS PROTIG 250 DC TRI Manual

28 August 2025