Louroe Electronics MS-D1 Manual

Louroe Electronics Ikke kategoriseret MS-D1

Læs gratis den danske manual til Louroe Electronics MS-D1 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Louroe Electronics MS-D1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Requires Cat5e or Cat6 Cabling,

(Not Included). See wiring

CONNECTIVITY on Page 2.

WIRING REQUIREMENTS

DESCRIPTION

The MS-D1 Mute Switch is an accessory for all Louroe Digifact Audio Monitoring/Audio Surveillance Systems when

microphone muting is required remotely from any Digifact hardware with a microphone. The MS-D1 contains a built-in

rocker switch with a Green L.E.D. mounted to a single gang stainless steel face plate. It is easy to setup in any

environment using 2 pairs of Cat5e or Cat6 cabling. The MS-D1 is used to mute or disable the audio feed to any

Digifact E hardware. It disables the audio stream from processing audio in the Digifact hardware, which prevents the

operator from listening in to the microphone. The MS-D1 fits into a single gang back box (not included) for mounting, on

a flat surface or in a wall.

Select the following settings from the (Output Settings Tab), 1.) Select Trigger Source and set it to (Input 1), 2.)

Select Output Port, set it to (Digital Mute). When finished, disconnect the RJ45 cable to your Digifact Hardware, set

the MS-D1 switch to the OFF position. Follow the wiring Diagram 1A. on page 2 for all wiring connectivity between the

MS-D1 digital controlled mute switch and your Digifact hardware. Testing: 1.) Reconnect the RJ45 cable and wait for

the Digifact hardware to power-up, now set the MS-D1 to the on position, the Green L.E.D. should turn on indicating

the Digifact hardware audio stream is muted.

OPERATION

MODEL MS-D1

MS-D1, Part No. LE-831

Digital Controlled (Analog Audio) MUTE SWITCH

INSTALLATION AND OPERATING INSTRUCTIONS

6955 VALJEAN AVE, VAN NUYS, CA 91406

PH: (818)994-6498 / FAX: (818)994-6458

/ www.louroe.comtechsupport@louroe.com

Page 1 of 2

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: sales@louroe.com

(818)

LE-831-01272023-WB

The MS-D1 works with all DIGIFACT Hardware

SPECIFICATIONS OF MS-D1 MUTE SWITCH

Digital Output Voltage

UTP, Cat5e, Cat6 Distance

Switch Contact

Dimensions

Faceplate Material

5Vdc

Up to100 ft.

5A @125Vac

Weight

Shipping Weight

2.5 oz

1 lb

2 ¾ W x " 4 ½" H

303 Stainless Steel

Backbox Single gang electrical

box (not included)

Package Includes:

1 x Single Gang Stainless Steel Wall Plate with a On/Off

Rocker Switch and Green L.E.D..

2 X Stainless Steel Screws

2 X Audio Monitoring On These Premises Stickers

DIGIFACT TECHNOLOGY

Please Note!

All specifications are subject to change without notice.

INSTALLATION AND OPERATING INSTRUCTIONS (MS-D1), Part No.: LE-831

Page 2 of 2

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: sales@louroe.com

(818)

IMPORTANT NOTICE

When this equipment is used as part

of an audio monitoring system, the

law requires that the public be given

notice of AUDIO MONITORING ON

THE PREMISES.Two decal notice

stickers are included with each MS-

D1, LE-831 units when shipped.

AUDIO

MONITORING

These Premises

WARRANTY

LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.

Should a defect appear within two year (24 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.

This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS .

This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation

instructions provided by LOUROE ELECTRONICS.

Returned shipments to LOUROE ELECTRONICS shall be at customer’s expense. LOUROE ELECTRONICS will return the equipment prepaid via best way.

10 Position Digital I/O, Power Terminal Block

available on all Digifact hardware

5VDC, Max load 100ma

Digital Output (1)

Digital Output (2)

Digital Output (3)

Digital Output (4)

Digital Input (1)

Digital Input (2)

Ground