Lowrance EP-25 Speed Manual

Lowrance Marine EP-25 Speed

Læs gratis den danske manual til Lowrance EP-25 Speed (8 sider) i kategorien Marine. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Lowrance EP-25 Speed, eller vil du spørge andre brugere om produktet?

Side 1/8
1
Pub. 988-0154-451
EP-25 Speed
Electronic Sensor
Installation Instructions
This instruction sheet tells how to install your EP-25 Speed sensor and
connect it to a NMEA 2000 network using LowranceNET network
components. You must refer to your digital gauge, sonar or GPS unit's
manual for sensor operation instructions.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. You should decide where to
install all components before drilling any holes in your vessel.
Some sonar or GPS units may require a software upgrade to display
NMEA 2000 data correctly and a manual addendum describing how to
operate the sensor. You can download these free and get additional
information on the NMEA 2000 compatible LowranceNET system at
our web site, www.lowrance.com.
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending. See our web site for the latest
product status information.
The EP-25 Speed sensor.
The EP-25 consists of the paddle wheel module, a blue female locking
cable connector and the smart module. The cable length from the
Paddle wheel module
Smart module
Blue female NMEA
2000 connector
2
connector to the smart module is 18 inches (46 cm) and from the smart
module to the paddle wheel module is 10 feet (3 meters).
The smart module converts speed data from the paddle wheel to the
NMEA 2000 data format. This allows any digital gauge, sonar or GPS
unit connected to the NMEA 2000 network to display the speed.
The EP-25 Speed, like the other Lowrance Electronic Probe (EP)
sensors, is designed only for use with a NMEA 2000 Network. It must
be connected to a NMEA 2000 network or it will not function.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If you are connecting to an
existing LowranceNET network, those are all the electronic
components you need. If this is the first sensor you are connecting, you
will also need a one-time purchase of a LowranceNET Node Kit.
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2 foot (61
cm) extension cable, T connector, 120-ohm male terminator and 120-
ohm female terminator.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one refer to the "Setup and Installation of NEMA
2000 Networks, General Information" document (part number 988-
0154-172) included with your EP-25 sensor. If that document is missing
it can be downloaded free from the Lowrance web site.
Supplies are not included, unless otherwise indicated. Required supplies
for this job are: four #8 stainless steel wood screws (3/4" or 19 mm long),
high quality, marine grade above- or below-waterline sealant compound.
Recommended tools for this job include: screwdriver, drill, 1/8" (3 mm) drill
bit for pilot holes. If you want to feed the smart module or blue cable
connector through a transom or bulkhead, you will also need a 7/8" (22
mm) drill bit.


Produkt Specifikationer

Mærke: Lowrance
Kategori: Marine
Model: EP-25 Speed

Har du brug for hjælp?

Hvis du har brug for hjælp til Lowrance EP-25 Speed stil et spørgsmål nedenfor, og andre brugere vil svare dig