LYYT DIY-DW120 Manual

LYYT Ikke kategoriseret DIY-DW120

Læs gratis den danske manual til LYYT DIY-DW120 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om LYYT DIY-DW120, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DIY LED TAPE KIT CW/WW –

153.739UK User Manual

DIY LED TAPE KIT 5m Cool white & Warm White –

Introduction:

Thank you for purchasing the Lyyt DIY CW/WW LED Tape. LED tape is ideal for use on the underside of a counter tops, shelves, cupboards,

around window frames or in an alcove of a ceiling to name just a few examples.

Before starting please ensure that you have read this instruction leaflet carefully.

If you are unsure about anything please have the tape installed by a competent installer.

Contents:

1 x 5m reel of CW/WW LED tape

1 x UK power adaptor

1 x Control Box with IR remote handset

Possible required tools: Scissors, Craft knife, Soldering iron and solder, 4 core DC wire and heat shrink tube.

Step 1: Preparation

Ensure the surface you are attaching to is clear of dust and dirt. Clean thoroughly and leave to dry before fitting the tape.

Step 2: Connecting IR Controller:

Connect the 4pin connector to the control box and then to the LED tape (FIG 1). Plug in the power supply and use the IR remote control to select

the various functions (Fig 2).

Unravel the tape to check that all the LEDs are functioning correctly. If there are any faults return to your retailer without delay.

FIG 1:

FIG 2:

IR remote function

The remote control has altogether 16 different colour temperatures to choose from, with other function keys as shown below:

* Fade mode: Press once for fade on both colours. Press twice for fade on cool white. Press 3 times for fade on warm whi . te

153.739UK User Manual

Step 2: Cutting

WARNING: Disconnect from the power supply before attempting any cutting.

Measure out each section and cut with sharp scissors only at the marked 10cm intervals. Do not discard any excess tape as it can be easily

reconnected and used again (see FIG 4).

Step 3: Fitting:

Clear the area you wish to install and remove the backing paper, exposing the adhesive tape. Push tape firmly onto the surface. It is recommended

to work on 50cm sections at a time in order to ensure a professional finish. When you reach the end of your installation cut at the marked cutting

point. The tape can be terminated at highlighted 10cm cut intervals if less than 5m is required.

FIG 3:

You may also reconnect the two pieces by soldering the point connections together. The tape has 3 tracks for the DC voltage:

To re-attached use a craft knife to cut the Epoxy coating from the terminals.

Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit in the process as it will not

work.

FIG4:

WARNING: Only cut the tape on the highlighted intervals. Cutting the tape in other parts without due care will permanently damage that section of

the tape and will result in malfunction.

Points to remember when using this tape

1) Only cut the tape at the highlighted 10cm intervals.

2) Do not connect another reel and operate from a single power supply as this will seriously affect the performance.

3) Ensure you connect the correct wires otherwise the tape will not work.

4) Ensure that there are no short circuits when solderin g.

5) We recommend use heat shrink to protect the connection. of tubes

6) Check that everything operates correctly before installing.

FAQ:

Q) Can you cut a 5m tape in many of different sections then solder connect them all together?

A) Yes as long as you cut the tape at 10cm intervals highlighted.

Q) Can I connect the tape together to form a loop?

A) Yes you can as long as both sides have a sufficient power supply it is possible.

Q) Can I use the tape outdoors?

A) Yes the tape is IP65 rated. Ensure though that the terminated ends are heat shrink protected.

Q) Can I use the LED tape without a controller?

A) Yes you can but you can only have a choice cool white and/or warm white. It would be better to buy single colour tape. of

Specifications

Voltage

12Vdc

Current consumption

300mA/m

Power consumption

3.6W/m

Number of LEDs

60/m

LED Spacing

16mm

Cut intervals

10cm

Beam angle

120°

LED type

SMD3528

IP rating

IP65

Errors and omissions excepted.

Produkt Specifikationer

Mærke:	LYYT
Kategori:	Ikke kategoriseret
Model:	DIY-DW120

Har du brug for hjælp?

Hvis du har brug for hjælp til LYYT DIY-DW120 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LYYT Manualer

LYYT CLIP10-B Manual

29 August 2024

LYYT DIY-CW60 Manual

20 August 2024

LYYT PS30-24 Manual

17 August 2024

LYYT LT24560-BL Manual

16 August 2024

LYYT DIY-B60 Manual

15 August 2024

LYYT DIYH-RGB30 Manual

14 August 2024

LYYT LT12560-WW Manual

14 August 2024

LYYT PS40 Manual

14 August 2024

LYYT RGB10-F Manual

14 August 2024

LYYT LT12560-CW Manual

14 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MiVue 540 Manual

2 August 2025

Pro User PSI2000TX Manual

2 August 2025

Guede 5T Manual

2 August 2025

Navman EZY40 Manual

2 August 2025

Thule Chariot Ski kit Manual

2 August 2025

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025