LYYT DIY-PK60 Manual

LYYT Ikke kategoriseret DIY-PK60

Læs gratis den danske manual til LYYT DIY-PK60 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 21 anmeldelser. Har du et spørgsmål om LYYT DIY-PK60, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

DIY LED TAPE KIT

User Manual

DIY LED TAPE KIT - SINGLE COLOUR

Introduction:

Thank you for purchasing the Lyyt DIY LED Tape . Kit LED tape is ideal for use on the underside of a counter tops, shelves, cupboards, around

window frames or in an alcove of a ceiling to name just a few examples.

Before starting please ensure that you have read this instruction leaflet carefully.

If you are unsure about any of the installation details, please have this installed by a competent installer.

Blister Contents:

1 x Reel of LED tape

1 x UK power adap tor

Possible Required tools: Scissors, Craft knife, Soldering iron and solder, 2 core DC wire and heat shrink tube.

Step 1: Preparation

Ensure that the surface you are attaching to is clear of dust and dirt. Clean thoroughly and leave to dry before fitting the tape.

Unravel the tape and connect the power supply. Check that all the LEDs are functioning correctly and if there are any faults return to your retailer

without delay.

Step 2: Cutti ng

WARNING: Disconnect from the power supply before attempting any cutting.

Measure out each section and cut with sharp scissors at the marked 5cm intervals to achieve the perfect length. Do not discard any excess tape as

it can be easily reconnected and used again (see FIG 2).

Step 3: Fitting:

Example 1: Simple straight run.

Clear the area you wish to install the tape and remove the backing paper, exposing the adhesive tape. Push tape firmly onto the surface. It is

recommended to work on 50cm sections at a time in order to ensure a professional finish. When you reach the end of your installation cut at the

marked cutting point.

Example 2: Requires cutting:

The tape can be cut at highlighted 5cm intervals for a perfect fit.

FIG 1:

DIY LED Tape User Manual Kit

You may also reconnect the two pieces by soldering the connection together (FIG 2). The tape has two tracks for the DC voltage with points +

positive pole at the top and negative pole at the bottom. –

To reattach, use a craft knife to cut the Epoxy coating from the terminals.

Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit when making these connections,

as this will result in malfunction and possible damage to the power supply.

FIG 2:

WARNING: Only cut the tape on the highlighted intervals. Cutting the tape in other parts without due care will permanently damage that section

of the tape and will result in malfunction.

Points to remember when using this tape

1) Only use the supplied power adaptor for the length of tape in the kit

2) Only cut the tape at the highlighted 5cm intervals.

3) Do not connect another reel and operate from a single power supply as this will seriously affect the performance.

3) The top track of the tape is the + Positive pole.

4) The bottom track of the tape is the negative pole. –

5) Ensure you connect the correct wires otherwise the tape will not work.

6) Ensure that when soldering there are no short circuits

7) We recommend use heat shrink tubing to protect the connection. of

8) Check that everything operates correctly before installing.

FAQ:

Q) Can I connect different colours in a chain?

A) Yes all the LEDs draw the same power, current and have the same connection but do not exceed the full reel length.

Q) Can you cut a reel of tape into many different sections then connect them all together?

A) Yes as long as you cut the tape at 5cm intervals highlighted.

Q) I have connected two reels together off one power supply and the LEDs are dim towards the end.

A) The power adaptor is only designed to operate the reel in the kit. Anything longer will seriously affect the performance.

Q) Can I connect the tape together to form a loop?

A) Yes you can. This will even the brightness out on the LEDS across the reel length

Q) Can I use the tape outdoors?

A) Yes, the tape is IP65 rated. Ensure that the terminated ends are heat shrink protected.

Q) Can I clean the tape?

A) Yes, the tape is IP65 rated and has an epoxy coating. Just wipe down with a damp cloth regularly to ensure continuing brightness

Q) Can I replace / patch damaged tape with a new piece

A) Yes, just highlight the effected area by the 5cm intervals. Cut out the faulty section then fit in a new piece soldering the connections securely

and using heat shrink to protect the repaired connection.

Specifications

Voltage

12Vdc

Current consumption

340mA/m

Power consumption

4.08W/m

Number of LEDs

60/m

LED Spacing

16mm

Cut intervals

5cm

Beam angle

140° - 160°

LED type

SMD3528 or SMD2835

IP rating

IP65

Produkt Specifikationer

Mærke:	LYYT
Kategori:	Ikke kategoriseret
Model:	DIY-PK60

Har du brug for hjælp?

Hvis du har brug for hjælp til LYYT DIY-PK60 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LYYT Manualer

LYYT CLIP10-B Manual

29 August 2024

LYYT DIY-CW60 Manual

20 August 2024

LYYT PS30-24 Manual

17 August 2024

LYYT LT24560-BL Manual

16 August 2024

LYYT DIY-B60 Manual

15 August 2024

LYYT DIYH-RGB30 Manual

14 August 2024

LYYT LT12560-WW Manual

14 August 2024

LYYT PS40 Manual

14 August 2024

LYYT RGB10-F Manual

14 August 2024

LYYT LT12560-CW Manual

14 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MiVue 540 Manual

2 August 2025

Pro User PSI2000TX Manual

2 August 2025

Guede 5T Manual

2 August 2025

Navman EZY40 Manual

2 August 2025

Thule Chariot Ski kit Manual

2 August 2025

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025