M-Audio MK-7 Manual
M-Audio
Midi-keyboard
MK-7
Læs gratis den danske manual til M-Audio MK-7 (4 sider) i kategorien Midi-keyboard. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 18 anmeldelser. Har du et spørgsmål om M-Audio MK-7, eller vil du spørge andre brugere om produktet?
Side 1/4
EVOLUTION MK-7 MIDI KEYBOARD MANUAL
1. General Guide
KEYBOARD
BACK PANEL
1. WHEEL button
2. SELECT button
3. PITCH BEND +/- switches
4. Numeric keys
5. PROGRAM key
6. BANK LSB key
7. BANK MSB key
8. WHEEL key
9. SAVE key
10. CHANNEL key
11. OCTAVE key
12. TRANSPOSE key
13. +/- keys
14. RESET-AC key
15. GM-RESET
16. MIDI OUT Connector
For connecting directly to PC sound card game port
17. DC Jack
For connecting to AC/DC adapter. DC output 9V-1 2V, 1 50mA, centre positive.
18. POWER switch
2. Power Supply
2-1 DC Power - Batteries (not included)
This unit is powered by 6 “AA” (UM-3) size batteries. Weak batteries will result in poor performance. When
the power is getting weaker, replace the worn out batteries as follows:
1. Remove the battery compartment cover and take out the batteries.
2. Insert new batteries and make sure that the polarity is correct.
3. It is advisable to replace all 6 batteries at the same time and not to mix batteries. Alkaline batteries are
recommended for maximum performance.
2-2 AC Power
You can also use AC adapter with the following specification: 9-12V DC output, 150mA, centre positive.
Note: Do not leave the adapter plugged in for long periods of time if the unit is not in use.
3. Preparation
This unit’s MIDI OUT connector is specially for connecting to personal computers.
3-1 Using the connector(16) directly plug into PC sound card game port.
3-2 Turn on the POWER switch (18).
3-3 Turn all other equipment’s power on.
4. Setting the MIDI TRANSMIT Channel
There are 16 MIDI transmit channels available. The value is 1 to 16. Set the unit’s MIDI channel. The unit
sends all MIDI messages on this MIDI channel. Be sure to match the channel with the RECEIVE channel of
the connected equipment.
4-1 Hold down the SELECT button (2) and ...
4-2 Press the CHANNEL key (10).
4-3 Press one (or two) of the numeric keys to change the channel. Also you can use +/- keys to increase or
decrease the value.
4-4 Release the SELECT button. Now the new TRANSMIT CHANNEL is set.
Note: The default CHANNEL is 1 when power is turned on.
5. Pitch Bend
Pressing the PITCH BEND switches (3) transmits MIDI BENDER (PITCH BEND) messages to connected
equipment. This allows you to bend the pitch of sound up (or down) to personalize your performance.
5-1 To bend up the pitch:
Press υ (+) switch.
5-2 To bend down the pitch:
Press τ (-) switch.
6. Wheel Assign
Use WHEEL to transmit MIDI CONTROL CHANGES. You can select and assign 119 types of MIDI functions
(1-31, 33-95, 102-121, 128-132)
Number Functions
1-127 Standard MIDI controllers
128 Pitch Bend Sensitivity
129 Fine Tune
130 Coarse Pressure
131 Channel Pressure
132 Velocity
6-1 Hold down SELECT button (2) and ...
6-2 Press WHEEL key (8).
6-3 Press numeric keys 0-9 (4) to select a MIDI function.
6-4 Release the SELECT button. Now the MIDI function is assigned to the WHEEL.
* If the number you press is not in the range of defined numbers, it is invalid. The previous function will be
retained.
* When you assign functions 120 or 121 you should use the WHEEL button to send MIDI messages.
7. Transpose
This function allows you to shift the entire pitch of the unit in semitone units. You can transpose the pitch
by 24 half steps (12 higher, 12 lower).
7-1 Hold down SELECT button (2) and ...
7-2 Press the TRANSPOSE key (12),
7-3 Press “+” or “-” key (13) to change the TRANSPOSE value. Each time you press + or - the keyboard is
transposed an additional half step.
* Press + and - key simultaneously to reset the pitch to default
7-4 Release the SELECT button. Now the TRANSPOSE is complete.
Note: Turning the power off always resets the shifted pitch to pre-set value.
8. Octave Change
This function allows you to shift the entire pitch one octave higher or lower.
8-1 Hold down SELECT button (2) and ...
8-2 Press OCTAVE key (11),
8-3 Press "+" or "-" key (12), the entire pitch will be shifted one octave higher or lower.
Produkt Specifikationer
| Mærke: | M-Audio |
| Kategori: | Midi-keyboard |
| Model: | MK-7 |
Har du brug for hjælp?
Hvis du har brug for hjælp til M-Audio MK-7 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Midi-keyboard M-Audio Manualer
15 August 2024
15 August 2024
15 August 2024
14 August 2024
14 August 2024
13 August 2024
13 August 2024
13 August 2024
12 August 2024
10 August 2024
Midi-keyboard Manualer
- Doepfer
- Arturia
- Motu
- Novation
- Medeli
- AKAI
- Casio
- ION
- Roland
- Pinnacle
- Keith MCmillen
- Yamaha
- Studiologic
- Swissonic
- CME
Nyeste Midi-keyboard Manualer
3 Marts 2025
3 Marts 2025
15 Januar 2025
29 December 2024
12 Oktober 2024
3 Oktober 2024
3 September 2024
3 September 2024
3 September 2024
3 September 2024