Makita AN924 Manual

Makita Hæftemaskine AN924

Læs gratis den danske manual til Makita AN924 (32 sider) i kategorien Hæftemaskine. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Makita AN924, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/32

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

Pneumatic Framing Nailer

Cloueuse Pneumatica

Clavadora Neumática de

Estructuras

AN924

IMPORTANT: Read Before Using.

IMPORTANT : Lire avant usage.

IMPORTANTE: Lea antes de usar.

2 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: AN924

Air pressure 0.49 - 0.83 MPa (70 - 120 PSIG)

Nail length (L) x Shank diameter (D) x Angle L: 50 mm - 90 mm x D: 2.9 mm - 3.76 mm x 21 degrees

(L: 2″ - 3-1/2″ x D: 0.113″ - 0.148″ x 21 degrees)

Nail capacity 64 - 73 pcs.

Minimum hose diameter 8.5 mm (5/16″)

Dimensions (L x W x H) 560 mm x 117 mm x 348 mm

(22″ x 4-5/8″ x 13-3/4″)

Net weight 3.8 kg (8.3 lbs)

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications may differ from country to country.

SAFETY WARNINGS

Important safety instructions

For personal safety and proper operation and main-

tenance of the tool, read this instruction manual

carefully before using the tool.

WARNING: WHEN USING THIS TOOL, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED TO REDUCE THE RISK OF PERSONAL

INJURY, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.

Personal Protective Equipment

1. Always wear safety glasses to avoid eye injury

from dust or fasteners. The safety glasses

should conform with the requirements of ANSI

Z87.1.

WARNING:It is an employer's responsibility

to enforce the use of safety eye protection

equipment by the tool operators and by other

persons in the immediate working area.

2. Wear hearing protection to protect your ears

against exhaust noise and head protection.

Also wear light but not loose clothing. Sleeves

should be buttoned or rolled up. No necktie

should be worn.

Flammable Atmospheres

1. Do not operate tool in explosive atmospheres,

such as in the presence of ammable liquids,

gases or combustible dust.

Tool modication

1. The tool should not be modied unless autho-

rized in the tool manual or approved in writing

by the tool manufacturer.

Tool maintenance

1. Refer to the tool maintenance instructions for

detailed information on the proper mainte-

nance of a tool.

Recommended fasteners and accessories

1. Use only fasteners made or recommended by

the tool manufacturer, or fasteners that per-

form equivalently to those recommended by

the manufacturer.

2. Use only accessories made or recommended

by the tool manufacturer, or accessories that

perform equivalently to those recommended

by the manufacturer.

Inspect tool before operating to:

1. Use only power source specied in the instruc-

tion manual.

Operate the tool within the specied air pres-

sure on the tool label for safety and longer tool

life. Do not exceed the recommended max.

operating pressure. The tool should not be

connected to a source whose pressure poten-

tially exceeds 1.38 MPa (200 PSIG).

2. Never use the tool with other than compressed

air. If bottled gas (carbon dioxide, oxygen,

nitrogen, hydrogen, air, etc.) or combustible

gas (hydrogen, propane, acetylene, etc.) is

used as a power source for this tool, the tool

will explode and cause serious injury.

3. Always check the tool for its overall condition

and loose screws before operation. Tighten as

required.

4. Make sure all safety systems are in working

order before operation. The tool must not

operate if only the trigger is pulled or if only

the contact element is pressed against the

wood. It must work only when both actions are

performed. Test for possible faulty operation

with fasteners unloaded and the contact ele-

ment in fully pulled position.

5. Always check contact element as instructed in

this manual. Fasteners may be driven acciden-

tally if the safety mechanism is not working

correctly.

Produkt Specifikationer

Mærke:	Makita
Kategori:	Hæftemaskine
Model:	AN924

Har du brug for hjælp?

Hvis du har brug for hjælp til Makita AN924 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hæftemaskine Makita Manualer

Makita MAC210Q Manual

11 August 2025

8 Juli 2025

8 Juli 2025

8 Juli 2025

19 Juni 2025

18 Juni 2025

2 Oktober 2024

13 August 2024

Makita DBN600ZJ Manual

13 August 2024

Makita AN613 Manual

11 August 2024

Hæftemaskine Manualer

Nyeste Hæftemaskine Manualer

Milwaukee M12 2540-20 Manual

12 August 2025

Milwaukee M12 2458-20 Manual

12 August 2025

Black Decker BCN115 Manual

9 August 2025

DeWalt DCN660 Manual

9 August 2025

Ozito SNG-2050U Manual

9 August 2025

Hikoki N1804DB Manual

7 August 2025

Hikoki NV45AB3 Manual

4 August 2025

Hikoki NV50AH Manual

4 August 2025

Hikoki NT1850DG Manual

4 August 2025

Hilti GX-IE XL Manual

3 August 2025