Makita DBO480 Manual

Makita Ikke kategoriseret DBO480

Læs gratis den danske manual til Makita DBO480 (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 28 anmeldelser. Har du et spørgsmål om Makita DBO480, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

INSTRUCTION MANUAL

Cordless Finishing Sander

DBO480

DBO481

DBO482

ENGLISH: Original instructions

Read before use.

7 ENGLISH

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsystem.This

systemautomaticallycutso󰀨powertothemotortoextendtool

andbatterylife.Thetoolwillautomaticallystopduringoperationif

thetoolorbatteryisplacedunderoneofthefollowingconditions:

Overload protection

Whenthetoolorbatteryisoperatedinamannerthat

causesittodrawanabnormallyhighcurrent,thetoolauto-

maticallystopswithoutanyindication.Inthissituation,turn

thetoolo󰀨andstoptheapplicationthatcausedthetoolto

become overloaded. Then turn the tool on to restart.

Overheat protection

Whenthetoolorbatteryisoverheated,thetoolstops

automatically.Inthiscase,letthetoolandbatterycool

before turning the tool on again.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automatically.Inthiscase,removethebatteryfromthe

toolandchargethebattery.

Protections against other causes

Protectionsystemisalsodesignedforothercausesthatcould

damagethetoolandallowsthetooltostopautomatically.

Take all the following steps to clear the causes, when the tool

hasbeenbroughttoatemporaryhaltorstopinoperation.

Turnthetoolo󰀨,andthenturnitonagaintorestart.

2. Chargethebattery(ies)orreplaceit/themwith

rechargedbattery(ies).

3. Letthetoolandbattery(ies)cooldown.

Ifnoimprovementcanbefoundbyrestoringprotection

system,thencontactyourlocalMakitaServiceCenter.

Switch action

CAUTION: Avoid turning the tool on while it

is placed on the workpiece or on your workbench.

Itmaycausepersonalinjuryordamage.

Turning the tool on and o󰀨

Press the power/speed select button to start the tool.

The tool starts to run at its highest orbital speed.

Press the stop button to stop the tool.

1 2

Fig.3

►1. 2. Power/speed select button Stop button

Changing the tool speed

The orbital speed can be changed in two modes; high

and low. Choose either mode depending on the applica-

tion and workload.

Press the power/speed select button to switch speed

mode while the tool is running.

Fig.4

►1. Power/speed select button

Speed settings table

Speed level Orbital per minute

2 (High) 14,000 min-1 (/min)

1 (Low) 11,000 min-1 (/min)

NOTICE: If the tool is operated continuously

at low speeds for a long time, the motor will get

overloaded, resulting in tool malfunction.

NOTICE: Select an appropriate speed range for

your sanding operations to avoid overheating

and melting the workpiece. Sanding at high orbital

speedmayheatworkpieceandmeltitatthepointof

contact.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o󰀨 and the battery cartridge is removed

before carrying out any work on the tool.

Installing and removing abrasive

paper

CAUTION: Always make sure that a sheet of

abrasive paper is installed securely before use.

Thepapermayotherwisebeloosened,removed

easilyandsubjecttoslippage,resultinginuneven

sanding operation.

NOTE: Bending the paper beforehand makes attach-

ment easier.

Produkt Specifikationer

Mærke:	Makita
Kategori:	Ikke kategoriseret
Model:	DBO480

Har du brug for hjælp?

Hvis du har brug for hjælp til Makita DBO480 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Makita Manualer

29 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

Makita BL4040F Manual

6 Februar 2025

Makita MR007GZ Manual

12 Januar 2025

Makita TW010G Manual

7 Januar 2025

Makita UT002G Manual

16 December 2024

Makita UM164D Manual

16 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox Airvox SW695 Manual

15 Juni 2025

Stiga SBC 635 KD Manual

15 Juni 2025

Cleveland 36CGM300 Manual

15 Juni 2025

Gourmia GTF7970 Manual

15 Juni 2025

Planet Audio P9630B Manual

15 Juni 2025

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025

Lavex 842CD12VST12 Manual

15 Juni 2025

Marshall RCP-PLUS Manual

15 Juni 2025

Hughes & Kettner BassForce XL Manual

15 Juni 2025

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025